You need to press F1 to enter the DOS to enter the computer, and it is useless to set the CDROM from

After entering the BIOS, there is an Advanced or Boot option, just select First Boot as CDROM or ***ROM, and then F10 to save and restart.

Press F1 because the system has become a floppy drive to start, the root cause is that the motherboard battery is dead, replace it with a new battery and it's OK, press the DEL key or F2 key when starting, enter the BIOS, enter the Advanced BIOS Features, change the first boot (First) to CDROM, you can start from the optical drive, change the detection floppy disk to none By the way, set the next time.

Press F1 because the system has become a floppy drive to start, and you can turn off the floppy drive.

Turn off the floppy drive and you're good to go.

1. The battery on the motherboard is dead.

Solution: Replace the motherboard battery.

2. You have set up the floppy drive to start, but there is a problem with your floppy drive.

Solution: A. Press del to enter the BIOS at boot, boot up the boot sequence, and turn off the floppy drive to boot.

b. Turn off the detection function of the floppy drive when it is turned on

Start the computer, and then press the [DEL] button to enter the main BIOS settings interface;

Select the "Advanced BIOS Features" setting item and press the Enter key to enter;

Set "Boot Up Floppy Seek" to "disabled" to turn off boot software detection.

It takes F1 to boot up, because the floppy drive in the BIOS is turned on, and it can be turned off after entering the BIOS.

For the problem of BIOS tuning, carefully study your motherboard manual, turn off the F1, you should be using an ASUS motherboard.

It's useless to say too much and you don't understand.

Tell you the easiest way.

Remove that little battery from the motherboard. It's right in the bottom right corner of the motherboard. The round and flat kind.

Let it sit for tens of seconds. Then put it back on. See if the problem is solved.

If it hasn't been resolved. Install a system: Rainforest Wood Wind Pure Edition SP3

The BIOS battery is dead. Floppy drive turned off.

The method of combining the first and second floors is soft and hard.

Copy down the prompt on the screen to press F1.

There was an error with the system boot bootloader.

If you don't have any important data, redo the system.

If there is, remove the hard drive and hang it on another PC, set it as a slave disk, back up the data of the C drive after booting, and then hang it back and reinstall it.

Be careful when the fan sound gets louder, if the fan sound gets louder, the CPU temperature will become higher, and the computer will automatically shut down, I see that you are not a CPU relationship like this, it may be that the electronics on the motherboard are out of power, change one and take a look,

You send the string of english on the screen and help you read it.

Press F8 to enter an options menu, there are many options, but none of them have DOS, but you can go to the console and try it.

None of them can get into DOS

However, F8 can enter safe mode.

None of them can get into DOS, press F2 to do it.

Press F5 to enter safe mode.

No, it's hard to press the del key at startup.

The floppy drive is not properly set up or the motherboard battery is dead.

This is not necessarily a problem with the settings, sometimes your hardware device is loaded incorrectly, or when the BIOS battery is dead, it will appear an error prompt of pressing F1 to start, it is recommended that you copy down the error prompt, and then compare the BIOS error message below:

The above error message will be followed by "press f1 to ..."If you find that the device is loading an error after the comparison, you will enter the BIOS, and select the load default setting "load default setting" in one of the last optionsAlthough the BIOS settings are somewhat different for different versions, the option to load the default settings is generally in the last item of the BIOS settings, and it is usually in the English text above.

If there is a "CMOS battery state low", that is, the CMOS is out of power, then you have to open the case, fold off the BIOS battery, and replace it with another battery, generally 3,4 yuan can be bought, if you don't know how to change, just ask a friend of your computer to help, in fact, it is very simple to change! Good luck.

It's not that there's a problem with the DOS, it's that there's a problem with the data in the BIOS.

1. Some data is not set properly, reset it.

2. The battery is in poor contact, reinstall it.

3. The battery is out of power, so I have to try it again, heh.

4. Worst-case scenario, hardware damage!

Boot the device and press del to enter the BIOS and set the floppy drive to desable

There will be no power on pressing F1.

It's BIOS. You turn on the phone and press del.,Go in and modify whatever you want.,Change it back.。。 Then press F10, press Enter, and it's good to go after restarting.

It is likely that the floppy drive is enabled in your BIOS, and you can disable the floppy drive in the BIOS.

If not, you can try to restore the BIOS settings to its default settings, which has an option.

If it still doesn't work, then try to change the battery, it may be that the battery is dead.

If it doesn't work, hehe, you have won the lottery, you can go and buy a lottery ticket :) This situation should be that there is a problem with the circuit of your motherboard BIOS, if you don't care about changing the F1 button every time you turn on the computer, then ignore it, there is nothing else.

Boot press del to enter the BIOS and set the floppy drive to empty, and if the date and time are not set, it will also appear.

Loaded floppy drive, you can press the del key when booting, enter the BIOS, enter the first option, turn the floppy drive A or B inside, and the display is that option is turned off, save and reboot.

There is a problem with the BIOS, it is estimated that the coin cell battery on your motherboard is dead, and the problem will be solved by changing it.

There are three situations, one is the problem of the floppy drive, the second is the data cable of the hard disk, the third is the motherboard battery, and the situation that something else is not moving is that the motherboard's battery is out of power, and it is good to change it and then enter the system to set the time.

The motherboard battery is dead, right? Just change it.

You try to change the battery in the BIOS first, and then set the startup items in the BIOS interface, in the advanced options.

The battery is dead, let's get another one!

All of the above are true, but sometimes if the system is modified and f8 is disabled, you can't press it!

Restore or reinstall it, you translate this sentence and you'll know why.

Disk error! Backup the file to repair the disk.

If not, enter the BIOS to see if it is a denial of the hard drive? Reinstall the operating system, if it doesn't work, it's a problem with the hard disk.

1.Replace the motherboard electromagnetic Discharge before replacement.

2.From the Xin'an system.

3.Use the PQ tool that comes with the installation disc to specify the C drive as the main one.

The small battery on the motherboard is removed and installed two minutes later.

What system is your machine using now?,It's generally fn plus f5 and f6 There will be a sun on it.,If it's useless, don't look for the shortcut driver.,Go to the official website for the next graphics card driver and try again.。

Which key has the logo of a small sun on it? Press fn and press the little sun button at the same time to try, some are different, some are on the arrow keys, you look carefully.

You can go and install a keyboard pixie!