I connected the cable to my friend s to go online

You add a router to your friend's place, and then set it up in the router and change it to go online without dialing the number.

1.If he's talkative, tell him not to shut him up.

2.If you don't want to send someone under the fence, buy a cat yourself, about 100 or more, it's worth it for the sake of surfing the Internet.

3.There shouldn't be any other way, hehe! I'm new, please teach me more.

I'm sorry to tell you that the "cats" are turned off and can't access the Internet.

I'm sorry to tell you that the "cats" are turned off and can't access the Internet.

I'm sorry to tell you that the "cats" are turned off and can't access the Internet.

I'm sorry to tell you that the "cats" are turned off and can't access the Internet.

Immortals can't save it.

Share the monthly rent of the Internet with him equally, then he won't dare to turn it off.

You must have a cat and a router device to ensure that you can surf the Internet normally after he shuts down, provided that the cat and the router cannot be turned off!

Only to call him to keep the "cat" and the router on all the time.

It's better that way.

<> as shown in the figure, router 1 is the LAN used by user A, and a network cable (gray) is connected to the LAN port of router 2 of user B's home by connecting a network cable (gray) from LAN port 1 of router 1, and the DHCP function of router can be used in the same way as the LAN port of router 1. Here's how to set it up:

First, connect the computer to the LAN port of the slave router, and change the IP address of the slave router to a different network segment address, as long as it is not in the same network segment as the main router. For example, most router addresses are, and we just need to change from router address to one;

Then turn off the DHCP function from the router in the settings;

Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

Buy a router and buy two network cables, one long and one short, you use the long one, and the short one is used by others. The network cable on the 1st floor of the Internet is connected to the router, and he uses one for you to use when throwing out two of them. You have to see for yourself how to release the line.

There are manuals when you buy a router, and it's OK to set up the router according to the instructions above!

Even if it's wireless broadband, you can't necessarily find a signal.,But it's estimated that the signal won't be good if you use a network cable.。。。 But it's better to choose to use a network cable.,Buy a wireless router.。。。 If you can use wireless, you can use wireless, and if you can't use wireless, the wireless router can also be plugged into the network and connected to the Internet. . .

Install a router on the first floor, connect the cat's network cable to the WAN port of the router, the router has four exits (LAN port), use two exits to connect a network cable to your respective computer, and then set it on your computer, 1. Set your local connection IP to automatically obtain IP, 2. Enter the password of the Internet into the route.

Buy a wireless router, about 100 yuan.

So far away, I still recommend you to use wireless broadband.

Clear the ARP cache and take a look.

Run input cmd

arp -a carriage return.

arp -d carriage return.

Could it be a conflict of IP addresses?

Connecting a network cable outside means that the network enters the home, which is connected to the cat first and then to the router.

To pass a broadband network cable through the router, you only need to dial up the Internet through the routing after passing the network through the cat, and then connect the computer to the router and LAN port respectively.

You only need to set the router to dial-up Internet access according to the manual, and then connect the WAN port of the router with the cat's wire, and connect the LAN port of the router to the computer.

Here's the answer: I can give you an affirmative answer, the wireless signal is not transmitted through this network cable, and you are not using the wireless function.

1. Wireless signal, is an independent working mode, the working mode and wired are separated, you must use the wireless receiver to carry out wireless transmission work, 2, routing, divided into wireless routing and ordinary routing, wireless routing is on the basis of ordinary routing with more wireless transmission signal function, ordinary routing is wired signal function, and no wireless transmission function, 3, if you use a notebook, turn on wireless connection and have used wireless connection to wireless routing, And you have added a root network cable to the router, at this time you want to know which one is working, I can tell you for sure, the working principle of Windows is to give priority to wired network communication, followed by wireless, if there is a wired connection, wireless will not work.

Dear, I hope it helps you

That's right, it's just that the way to access the Internet has changed from wireless to wired.

That's right.

That is, there are two ways to transfer data between your router and your device.

It's good to plug in a network cable from his router.,Pay attention to plug it in the LAN port.,LAN ports are generally four.,Just choose just one.。

1. Network cable is indispensable for connecting to LAN. There are three types of network cables commonly found in LAN: twisted pair, coaxial cable, and optical cable. A twisted pair is a data transmission line that consists of many pairs of wires.

It is characterized by being cheap, so it is widely used, such as our common **line. It is used to connect to the RJ45 head. It is divided into two types: STP and UTP, and we commonly use UTP.

2. A router, also known as a gateway device, is used to connect multiple logically separated networks, and the so-called logical network represents a separate network or a subnet. When data is transferred from one subnet to another, it can be done through the router's routing function. Therefore, the router has the function of judging the network address and selecting the IP path, it can establish a flexible connection in the multi-network interconnection environment, can connect various subnets with completely different data packets and media access methods, the router only accepts the information of the origin server or other routers, and belongs to a kind of interconnection device at the network layer.

Ask yourself if it's okay to plug it into the router as well.

Hello question, do you also plug in the same hole?

Question: It's okay to plug in the holes on both sides to connect the network cable, right?

Question Okay, thank you.