What s going on with the computer monitor flashing out of English

There are times when our computer turns on and the monitor keeps flickering, what should we do? Let me give you a brief introduction to the reasons and solutions for the computer to keep flashing on the computer boot display!

Solution 1 for the computer boot monitor keeps flashing:

1. Your power supply is unstable, and the thermal performance is not good or the anti-interference performance is poor, resulting in excessive output voltage ripple, which makes the graphics card in a state where it cannot work normally, resulting in screen flicker.

Solution: Turn on the power supply and replace its switch tube and filter capacitor.

Or just change the power supply.

Second, the performance of the display tube is poor, resulting in high voltage, the screen is too bright and white, and the brightness potentiometer.

Serious oxidation, small resistance or poor contact, circuit failure leads to the acceleration pole voltage of the display tube is too high or the pant tanqin pole voltage is too low, will cause this phenomenon of computer screen flickering, especially the initial phenomenon is very similar to your current problem.

Solution: If the screen flickers when the machine is turned on, tap the monitor to see if the phenomenon is aggravated (don't use too much force after stopping). If it is aggravated, the problem of the display is mostly caused by the poor contact of the above parts, and it is necessary to find a professional to repair it.

3. Graphics card interface.

Poor contact, poor thermal performance of the graphics card, and poor contact of the display cable, etc.

1. Unplug the graphics card, check whether the interface is rusty, and use anhydrous alcohol.

Wipe it clean while slightly cocking the shrapnel.

2. Shut down immediately after the phenomenon appears, pull out the graphics card with cotton gloves or cotton cloth, test whether the graphics card chip is overheated (generally slightly warm) by hand, change the fan if it is overheated, or change the chip and graphics card.

3. Use a multimeter.

The resistor R*1K block test whether the display wire is in good contact, and the wire should be shaken during the test, and the possibility of its damage is small.

Solution 2 for the computer to keep flashing the computer boot display

1.First of all, we right-click on the blank area of the desktop screen and click on Properties.

2.Properties, open the Settings tab.

3.Click Advanced.

4.Click on the Monitor tab.

5.In the drop-down options of screen refresh rate, select the highest frequency, usually 85, and click Confirm.

1. The screen display system is busy, please press any key to continue.

1) Insufficient virtual memory causes system multitasking errors.

2) CPU overscreen causes operation errors.

2. Memory module.

incompatibilities or corruptions cause arithmetic errors.

3. Attacked by unknown programs or viruses.

4. Caused by the bloated system.

5. The optical drive is opened abnormally when reading the disk.

When we turn on the computer, sometimes we will encounter the situation that the computer displays English and the screen is flashing. This situation is usually caused by a problem with the computer system.

First of all, we need to make it clear that a splash screen means that the screen flashes by and disappears quickly; Instead of staying on the English interface all the time. If it's a splash screen, then the problem may be due to a hardware failure or a driver hall merge sequence issue.

However, if the screen stays on the English interface, then the problem is most likely due to a problem with the operating system or startup program. At this point, we need to try the following methods to solve this problem.

First of all, we can try to restart the computer by pressing "Ctrl+Alt+del". If this method doesn't work, we can try to enter safe mode to fix it. The way to enter safe mode is to press the F8 key while booting on and then select "Safe Mode" to enter.

In safe mode, we can do things like system recovery or update drivers.

If none of the above methods can solve the problem, then we may need to use a system installation disk to repair the system. First of all, we need to plug the system installation disk into the computer and restart the computer. Then, press the corresponding button at boot time to enter the BIOS settings and set the system installation disk as the boot disk.

Finally, follow the prompts on the system installation disk to perform system repair or reinstall the operating system.

In short, when we encounter the situation that the computer keeps showing English and the screen is flashing when the computer is turned on, we should not panic, we can try the above methods to solve the problem. If it still can't be solved, then we can seek help from a professional.