Xunteng water heater is used, Xunteng instantaneous electric water heater does not heat

How to use: 1. In the case of not using hot water often (such as using it once every two or three days), the frequency of use of the electric water heater is not high, so you can turn off the power of the storage electric water heater during the time when it is not in use, and turn it on an hour before use, which can save a lot of electricity bills.

2. For the use of electric water heaters every day, but the amount of hot water used is not very large, then turn on the heating function of the storage electric water heater an hour before use, and turn off unnecessary functions at other times, which can also save part of the electricity bill.

3. In the case of frequent use of hot water and a large amount of hot water, it is recommended to turn on the storage electric water heater all the time, but adjusting the hot water temperature according to the frequency of use and the amount of hot water used can also play a certain role in energy saving.

4. Be sure to fill it with cold water before heating it with electricity. And the tap water is required to be in a normally open state to ensure that the water tank is always water. In order to prevent scalding, you can open the cold water valve first, and then open the hot water valve; When closing, close the hot water valve first, and then turn off the cold water valve.

You are buying an instantaneous electric water heater, the reason for the temperature instability may be that the water pressure fluctuation in your home is large or the voltage fluctuation is large, especially when the voltage is low, the machine may stop working, and the voltage will resume work immediately after the voltage is normal, so it will cause overtemperature.

One is that the water in the tank is not full, open the inlet and outlet pipes to add water and discharge air: the other is that the water pipes are not installed correctly.

My home is also this water heater, the water temperature is too unstable, used for more than a month, I took a good bath twice, the rest is the head has not been washed before the water temperature is cold, every time I take a bath I am very irritable, what kind of water heater is this! It sucks,

Summary. Dear, there are other possibilities: 3. If the over-temperature protector fails, we only need to reset the device, and it can be heated normally, if it still can't be heated, and the over-temperature is displayed, the <>device must be replaced

4. It may be that the instantaneous water heater has a short circuit and has a self-protection device, which cannot be carried out, and it needs to be checked and <>repaired

Centon's instantaneous water heater does not heat.

Hello dear, glad to answer for you! The reasons why the Dong Li Ji Xunteng instantaneous electric water heater does not disturb the heating are: 1. The water pressure is unstable, the water pressure is too low, and you can avoid the peak period, or add a booster.

2. If it is caused by the blockage of the gas path, it <>can be dredged

Dear, there are other pickpockets that can be: 3. If the over-temperature protection device fails, we only need to reset the device, and the world can be heated normally, if it still can't be heated, and the over-temperature is displayed, the <>device will be replaced

4. It may be that the instantaneous water heater has a short circuit and has a self-protection device, which cannot be carried out, and it needs to be checked and <>repaired

Turn on the water before the machine starts heating. Wait for about 10 seconds for the temperature to stabilize. And then according to their actual needs. Heating up or cooling down. This method is suitable for all instantaneous water heaters

Please explain first, what kind of water heater is yours? Is it a water storage drum, a quick-heating one, or an instantaneous water heater? Also, you said that the temperature display has risen, and the temperature of the water has not changed, right?

Xunteng brand water heater, what is the automatic temperature jump?

It is estimated that it is scale, you look for the after-sales service of the water heater to take a look.

Summary. 2.Use a tool to open the drain and unscrew the nut of the hot water outlet to block the hot water outlet and prevent the water from the water heater from flowing out.

At the same time, unscrew the nut of the cold water nozzle, connect the hose (shower pipe can be) to drain the water, until there is no water flowing out of the cold water inlet, and the 50L water heater will drain the water for about 1 hour. 3.Remove the hose connected to the cold water inlet, connect one end of the hose to the hot water inlet, and the other end to the faucet, open the faucet and fill the water for 1 minute, and plug the cold water inlet, let the cold water in the inner tank for a while longer, then open the cold water inlet to drain the water, repeat several times until the discharged water is clean.

1.You need to unplug the socket and close the two triangle valves first.

2.Use a tool to open the sewage outlet, unscrew the nut of the hot water inlet, block the hot water inlet, and prevent the water pie loss cover of the dust stop water heater from flowing out. At the same time, unscrew the nut of the cold water nozzle, connect the hose (shower pipe can be) to drain the water, until there is no water flowing out of the cold water inlet, and the 50L water heater will drain the water for about 1 hour.

3.Remove the hose connected to the cold water inlet, connect one end of the hose to the hot water inlet, and the other end to the faucet, open the faucet and fill the water for 1 minute, and plug the cold water air inlet, let the cold water in the inner tank for a while, then open the cold water inlet to drain the water, repeat several times, until the discharged water is clean.

After the power is on, the indicator light is not on, and the measurement of low voltage is normal.

Do you have hot water? There is no hot water, and even the indicator light is not on.

External malfunctions and failures in the water heater itself keep the lights off. Generally, check whether the socket voltage at home is normal, whether the power supply is tripped, whether the power cord is off, loose or damaged, and if it is normal, it is considered that the water heater itself is faulty. The thermostat and thermostat of the water heater are extremely important, and the aging or damage of any one component will cause the indicator light to not light up.

Seepage before sail. The thermostat is not open.

You take an electric pen and check step by step whether it is powered on. But for water heaters, I suggest you find a professional closed stool or someone to repair the coarse potatoes. If the consequences of self-resolution are still serious, <> pro

How to detect the thermostat.

Test the front end, the front end is electrified, that is, the thermostat is damaged.

How to use: 1. Turn on the power supply, and the power indicator light will be on;

2. Adjust the temperature gear, low in summer, middle in spring and autumn, and high in winter;

3. Check that the heating indicator light is on when heating, and observe the temperature display that rises through the cavity;

4. Open the water outlet side valve of the mixing valve when bathing, and if the water is too hot, you can adjust it with the cold mountain water shortage valve in the mixing valve;

5. Rotate the temperature control to OFF when not in use, and rotate it to the appropriate temperature before using it again.