Do all cars start on a flat road without using the accelerator?

In fact, the oil separation cooperation is all about talking, basically all cars can be driven without the accelerator, but the accelerator can be added to start a little faster. Except for a car with a small displacement or a very, very low idle speed, then you need to add a little throttle to prevent stalling. In addition, if the car is fully loaded, then in order to prevent stalling, you have to add a little throttle to start.

Normally, you can start without oil, but if you don't give oil in subject 2, you can start without any problem.

But the correct start is to semi-tandem lubrication and then release the clutch completely, so as to avoid stalling as much as possible.

The accelerator pedal is also known as the accelerator pedal. It is part of the automobile fuel supply system. By controlling the amount of pedaling, the engine throttle opening is controlled, the air intake is controlled, and the computer controls the oil volume, so as to control the speed of the engine.

Basically, there is also the weight of the car, and if there are more people, you have to give some oil, so as not to turn off, phenomenon? I don't know exactly what its name is, but its clutch oil is set (I heard that it can be changed).

If it's not a manual gear, you don't need a clutch, it's just a brake.

No, lift the clutch to the semi-linkage on the flat road, give a little oil, but don't release the clutch completely, and wait for the car to walk smoothly before lifting it.

Idling is the speed at which the car itself does not throttle. Generally, novices are accustomed to releasing the clutch and then refueling the accelerator, which can easily cause the car to nod its head. It is recommended to add some throttle before the clutch is put into the semi-linkage, but not too much.

This is the case for cars with automatic transmissions.

If the idle speed is too high for a manual transmission car, it is recommended to lower the idle speed until the idle engine does not shake.

Both manual and automatic are perfectly fine, but heavy trucks are not.

When the car starts, you should step on the accelerator lightly, reason: because the engine speed is lower, the damage will be smaller, especially in winter, the car gasoline may freeze due to the temperature, you must warm it up, so that the oil can flow normally between the oil pipeline and the diesel engine, and increase the accelerator pedal, which is better for the car engine. In addition, having a large accelerator pedal at the beginning is extremely detrimental to the car engine, and will also cause fuel consumption to be higher than when you normally drive.

Therefore, when you are just starting out, it is also good to add a small accelerator pedal gradually, which can avoid many unnecessary losses.

According to the amount of trampling, the engine throttle opening is manipulated, the air flow is manipulated, and the remaining oil is controlled according to the computer, and then the car speed is controlled. First release the clutch to the clutch semi-linkage, and then you can refuel or not. When the car starts slowly, release the clutch.

The network accelerator of the vehicle is generally operated by the foot pedal, also known as the accelerator pedal, which is mainly used to control the engine's natural material supply equipment. The actual operation of the foot pedal should be supported by the right leg heel on the ground of the car cab, and the foot plate should lightly step on the accelerator foot pedal to cooperate with the extension and flexion of the knee joint to step on or release the pressure.

When starting the vehicle, do not press the accelerator. Most like the accelerator pedal is on the high side. To start, it is best to give a slight amount of oil before the clutch linkage point, and the opening degree of the accelerator pedal should be medium to small.

Release the clutch, tighten the feed, and move quickly. During operation, the accelerator pedal should be increased or decreased according to the real-time road conditions and actual demand. It is necessary to choose the appropriate gear, so that most of the car engine medium speed large accelerator pedal running, in order to save gasoline and diesel.

When changing gears, you have to add empty oil, and you should cooperate well with the clutch and the oil.

Correct control of the throttle, the accelerator pedal of the vehicle engine, which is generally adjusted by the foot pedal, also known as the accelerator pedal, is the oil device provided by the engine control of the vehicle. The control of the throttle should be supported by stepping on the ground of the cab with the right leg as a support point, and the foot plate should be stepped on the accelerator pedal, and the flexion and extension of the knee joint should be used to press or release the pressure. When stepping on the accelerator, use gentle pressure to ensure that the pedal is lifted slowly.

When starting the diesel engine, the accelerator pedal does not have to be pressed down, and it is advisable to be slightly higher than the standby accelerator pedal. At the start, the oil should be slightly before the clutch linkage point, and the opening degree of the accelerator pedal should be at a small and medium-sized level. The pressure release clutch should be closely coordinated with the oil feed, and the action should be agile.

At the beginning of driving, if you want to save fuel, you can only step on the accelerator lightly, and if you step on the accelerator sharply, the fuel consumption will increase significantly. This is actually a cliché problem, we often say to drive gently, avoid sharp acceleration, sudden braking and other violent driving operations, the purpose is to save fuel and protect the car.

I think the car should be lightly pressed on the accelerator when it starts; Because if you step on the oil brain to the end, it is likely to cause a lot of damage to the car's engine, and lightly pressing the accelerator can also make your start more stable.

It must be a light step on the accelerator, driving too fast and starting is too dangerous!

Nowadays, more and more people are buying cars, and many novices are just after taking the driver's license and can't wait to drive on the road, however, this also leads to many novices who do not know much about the performance of the car and the driving method, and the impact of bad driving behavior on the car cannot be ignored.

Don't think that stepping on the accelerator is a very simple thing, but in fact, many riders may not know which hurts the car more than pressing the accelerator hard or starting slowly. Many people will think that slamming on the accelerator will cause very much damage to the engine, is it really as everyone thinks?

In fact, from the perspective of maintaining the car, it is indeed better to slam on the accelerator than to start slowly, because the car will have some problems with both the engine and accessories as the time of use increases.

One of the inevitable is the carbon deposit of the engine, and slamming the accelerator when driving can allow the engine to run at high speed, which can reduce the formation of carbon deposit to a large extent.

However, from a safety point of view, it is better to start slowly, especially when waiting for traffic lights at intersections, if you press the accelerator sharply, there are vehicles in front of you and the distance between vehicles is close, it is easy to cause a rear-end accident.

Even if it is the first car, if some non-motorized vehicles and pedestrians do not obey the traffic rules when passing through the intersection, the cost of slamming on the gas pedal is too great.

Speaking of which, I believe everyone already knows how to do it, in fact, there are pros and cons to these two, and it is completely possible to make use of the strengths and avoid the weaknesses, and choose to start slowly when encountering intersections or traffic jams to ensure safe driving;

On a wide road with no pedestrians, we can slam on the gas pedal to drive and reduce some carbon deposits, which is also a double benefit.

It is better to start slowly when driving, which is also safe driving, and it is also better for the car.

It must be a good start slowly, without hurting the engine.

Which hurts the car more, "slow start" or "slamming on the accelerator"? After listening to the old driver's words, it suddenly dawned on me.

Start slowly, not too fast.

Start slowly, safety first.

Not good, it is just right, adopted, light, soft, in the way to the position to step on, so safe.

See if your oil is well suited.

Many friends will make such a mistake when driving, rushing to the gas pedal when starting, knowing that the engine will change gears when it reaches a certain speed, but unconsciously will step on the accelerator, so let's take a look at what are the disadvantages.

When driving an automatic transmission car, you can't press the accelerator pedal when you start, which will only increase the rev and cause the engine to roar loudly and the transmission to wear out, resulting in wasted fuel. Instead, you should slowly increase the throttle to increase the engine speed evenly, and then relax the accelerator pedal after the speed increases, and then continue to increase the accelerator, so that the speed of the car increases faster, and the acceleration of the vehicle feels smoother.

Not only should automatic transmission models not start with a deep throttle, but manual transmission models should not start with a deep throttle. Because of this, one is unsafe, the other is a waste of fuel, step on the accelerator deeply to start, the car will suddenly rush out, and an accident is likely to occur; At the same time, when you step on the accelerator deeply, the fuel consumption is extremely high, several times or even more than ten times that of usual.

The speed is determined by your car model, and it is different for each car. Don't increase the throttle too hard when starting, just go up slowly.

1. Generally, when the car starts, it is necessary to step on the accelerator while loosening the clutch.

2. Flat road starting operation:

First step on the clutch pedal with the left foot, put the right hand into 1st gear, press the horn with the left hand, release the parking brake lever with the right hand, then slowly lift the clutch pedal with the left foot to semi-linkage, slowly step on the accelerator pedal with the right foot to refuel, let go of the clutch pedal with the left foot after the car starts, and finally refuel with the right foot to speed up to the normal speed, drive the car into the normal lane and turn off the turn signal.

3. Half-slope starting operation:

When starting, due to the greater resistance, so the clutch should be more stable than the flat road 3-4 seconds, when you put down the hand brake, do not immediately loosen the clutch, must immediately refuel, and wait for the car to travel slowly 3-4m, and then slowly lift the clutch, so as to ensure that the car starts smoothly on the ramp and does not stall. To dare to refuel, start uphill, put down the handbrake, immediately refuel, so that the speed of the engine reaches about 1500 rpm, so as to ensure that the car uphill start with sufficient power, there will be no "shaking" phenomenon. The key to a smooth start on a ramp is to coordinate your hands and feet properly, otherwise, it will cause the engine to stall or the car to slip backwards.

This is a matter of habit, generally speaking, any vehicle on flat ground is to let go of the clutch and start, let go of the clutch and do not start and turn off should be a problem with the vehicle. However, when starting on sloping ground, you should properly increase the throttle and keep the start without turning off.

First, the design and tuning of the engine are not the same, the output effect will not be the same, for example, the engine of two different brands of car is the displacement, the cylinder diameter of car A is smaller than that of car B, but the connecting rod is longer than that of car B, and the engine of car B is opposite, when the speed is the same (such as 800 rpm is used), the torque generated by the two engines is not the same.

2. Why does the engine speed rise differently when you step on the accelerator? If the car itself is not faulty or aged, but only a comparison between new cars, it is also related to the first problem. Here's a quick example:

The automobile manufacturing company has strong R&D strength, accurate engine tuning, very good matching between the gearbox and the engine, and the throttle response performance of the car is definitely better than those cars that are roughly assembled, the engine tuning is average, and the gearbox and engine are poorly matched.

Generally speaking, it is explained in this way, the same is the displacement, for high-speed cars, the torque that begins to output is smaller, and the torque of low-speed cars is larger when starting, and the car with torque can start smoothly without oil, and the torque is small (high-speed cars) will stall without oil, generally speaking, the tool pickup belongs to the low-speed car (coach test car), and the start does not need to be fueled, and even the half-slope start can be without oil, and the family car is a high-speed car, the starting torque is small, if the semi-linkage is not good when starting, it will lead to stalling.

When the car starts on flat ground, it mainly adopts the method of lifting and clutching. To start, you need to engage 1st gear, turn on the turn signal, slowly lift the clutch pedal with your left foot to a semi-linkage state, and slowly release the parking brake lever with your right hand, while slowly pressing the accelerator pedal with your right foot to refuel. When the car is in a shaky semi-linkage state, release the clutch, and the car moves forward slowly, that is, the start is successful.

Generally, when you go to the car to start, before the clutch is completely released, you should add a little oil, of course, sometimes you can start without refueling (especially a new car), but at this time, the engine speed is not high, it is very laborious to start the car, and it is easy to turn off if you add that the road is uneven. Therefore, it is correct to add a little oil at this time to increase the power of the engine and make it easy for the car to start.

In a driving school, why can you start or reverse without refueling? This is because students generally do not master the use of the clutch, the oil clutch is not well coordinated, it is easy to turn off, affecting the training, therefore, the driving school deliberately adjusted the "idle speed", that is, the throttle has been slightly raised, and the students do not refuel, the engine is not the "lowest speed", of course, it will not turn off, but can start and reverse.

Steps to drive a car:

1. Open the door and go in to see if the gear is in neutral, 2. Step on the clutch with the left foot and unscrew the key, 3. Hold the steering wheel with the left hand and look ahead, hang a gear with the right hand, 4. Step on the accelerator with the right foot, and slowly open the clutch with the left foot, 5. Wait for the car to start steadily and then repeat the above operation according to the road conditions and step on the clutch to hang the second gear.

You can add a little throttle slowly, and pay attention to the oil off the fit.

Useful to give good reviews, thank you.

Automatic transmissions are generally not required. A manual transmission is a must.

Generally required, only a few with high idle speed do not need it.

Fuel is required for starting, mainly for a smooth and fast start.

Tips for starting a car with a manual transmission.

1.Adjust the seat before driving to make sure your feet can step on the clutch, brake and accelerator pedal more firmly and comfortably.

2.For cars with manual transmissions, when starting with a first gear, the clutch should be pressed to the end, and the right foot should be put on the accelerator to be ready.

3.When starting to start, the clutch of the left foot is slowly lifted to nearly half, when you feel that the vehicle is shaking, release the handbrake in time, and then gently click the accelerator, the car wants to move forward slowly release the clutch, and then add a little throttle to start successfully.

4.If you are a novice at the start on a ramp, you should pay special attention, if you release the handbrake too quickly and the clutch is not lifted into place, it is easy to slip. The best way to do this is to press the clutch and brake when starting, and the handbrake can be used or not.

When the clutch is lifted to the halfway point, release the brake, at this time the vehicle is in a semi-clutch state, the car will not slip back, and at the same time add the throttle, slowly release the clutch, and the start is successful.

Automatic car starting skills.

1.The automatic transmission car is relatively easy to start, mainly because its clutch and brake share a pedal, and like the manual transmission car, the seat must be adjusted before starting. Then hit the brakes and push the gear to the "D" position.

2.Then slowly release the brakes, quickly release the handbrake when the vehicle is shaking, and then follow up the accelerator to complete the start. The start of the ramp is the same as that of the flat road, except that the clutch is lifted to the exact position, that is, the vehicle does not slip back.