How can I make the scrollbar screen flash when Windows boots up? 25

1.Start -> run ->msconfig -> start -> all the hooks are canceled OK Restart A basket appears tick OK. ok.

2.Start -> run ->msconfig ->noguiboot tick to restart.

The scrollbar is gone.

If you want to surf the Internet, set an IP address, for example:

There are also a lot of pre-styled handles.

You can adjust the boot program.

Try not to open so many programs.

My computer, properties, advanced, system boot inside the tick.

Excerpts, I hope it helps you.

Original article] windows7 boot screen into a scroll bar repair process machine is installed windows7, a day normal boot machine for half a day no response, after the appearance of "a disk read error"; Reboot again "bootmgr image is corrupt." the system cannot boot."I know it's something wrong with the boot part of the system.

And several consecutive reboots, including entering the safe mode, etc., one of which the system automatically entered the repair state, after the repair is completed, the machine can enter the windows7 system normally, the only thing is that the boot screen has changed from the original four-petal animation to a scroll bar, but this does not affect the normal use.

Recently, on a whim I want to restore the original boot animation of windows7, according to the online method of those few commands to set the local boot to Chinese, and set to English, other languages, etc., even the boot file has been modified, but also used bcdautofix, ntbootfix and other tools are not good, boot is still scrollbar. Later, I went to Microsoft's official website and learned that the boot screen is run by CPU and cache, my machine CPU should be fine, the only thing is cache, and Windows7 is related to cache during the boot process, which is related to hard disk and memory, so check the memory first. My machine plugged in 4 memory sticks and removed 2 first, restarted the computer, and the four-petal boot animation was restored.

Later, the memory slots and memory modules were simply cleaned and swapped, and after several reboots of the computer, the four-petal animation was never lost. It seems that such a simple solution did take a few days, this method works on my machine, you can try this method if you have the same problem.

Run bcdedit without parameters, there are duplicate format sequence codes in the message, and then bring the corresponding sequence codes to the bcdedit parameters to run, example:

bcdedit /set ilocale en-us

1. If the hard disk light does not flash wildly when entering the system. It is usually a motherboard or power failure.

Generally, there is a capacitor on the motherboard or power supply that has exploded. It's more intuitive, take it apart to see if the motherboard capacitor is bulging. If spare parts are available. Try replacing the motherboard and power supply.

2. It is also possible that the memory module needs to be dialed down and erased with an eraser to prevent too much dust.

The dust of the CPU fan should also be cleaned once a year and a half to prevent the CPU temperature from being too high.

3. It is also possible.

There are too many illegal shutdowns.

Start it on the boot disk, and reinstall it if it doesn't work when the recovery console recovers.

What exactly is to be checked one by one.

It is recommended to do two first, then one, and finally three, of course, if your C drive or desktop has nothing important, it is also good to do three first.

This is an illegal shutdown or other reason caused by the disk damage, please repair it (fix each disk or only fix the C prompted).

Built-in disk repair method:

The specific steps are as follows: select the drive letter C in my computer, right-click the mouse to select the properties, select "Tools Start Checking" in the pop-up drive properties window, and select "Automatically repair file system errors" and "Scan and recover bad sectors", and then click Start, the scanning time will vary depending on the disk capacity and scanning options (after doing it according to the above method, a box will pop up, the point is, repair after automatic shutdown, and win78 select the Disk Check button according to the plan).

Bad sectors on the hard drive will lead to corruption or loss of computer system files, computer failure to boot or freeze. Hard disk bad sectors can be repaired using NDD Disk Utility or Scandisk.

If the fault persists, please restore the system or reinstall it (it is still not possible to format the hard disk and repartition and reinstall it, and go to repair it if it does not work).

If you can't get into the system, find a way to enter the system to repair the disk, press the enter key, wait a while to see if you can repair it yourself, reinstall the system, and go to the repair to help you.

If it only appears once, it won't come out next time, don't mind, it means that the system repaired the fault by automatically.