Is the home button flooded iphone7

No, the home button of the iPhone 7 is sealed, and the iPhone 7 supports water resistance.

iPhone phone water can try the following methods to solve.

Method. 1. Do not shake dry vigorously, which may cause water to seep into the deeper inside, and do not use a hair dryer to prevent the deformation of parts caused by high temperature heating. Use a cloth to dry as much water as possible that can be seen on the whole machine, and carefully dry the charging port, earphone port, speaker, volume button, lock screen key, mute switch and other parts.

You can also use a small thing such as a cotton swab to dry the moisture in the speaker's small holes.

Method 2: Put the mobile phone into a small bag of rice and seal it for 24 hours, so that the rice can absorb the water in the mobile phone. Alternatively, you can replace the rice with water-absorbing pellets such as desiccant, cat litter, or moisture-proof beads.

Method 3: Go to the Apple after-sales service center for professional maintenance.

If the home button fails to work in the water on the iPhone, you can use the assistive touch gesture function.

Here's how: 1. Open Settings

2. Open "General" in the settings

3. Turn on "Accessibility".

4. Open "AssistiveTouch" to use.

Hello dear, 1. The measures you took were not right when you entered the water, which caused the motherboard and circuit board to be damaged by a short circuit, and could only be sent to the official after-sales point for repair. 2. The correct way to save the iPhone from water ingress: (1) Dry it with a hair dryer, first take out the mobile phone that accidentally fell into the water, and use a paper towel to absorb the surface moisture.

Pay attention to the headphone jack and charging socket part with a cotton swab or roll the toilet paper into a thin strip of paper to suck up the water, do not use a toothpick to stuff the paper ball directly into it, a accidentally can not take out the paper ball will outweigh the loss. After absorbing water, use the cold air of the hair dryer to dry the mobile phone, but do not use the hot air function of the hair dryer, the conductivity of the water and the high temperature of the hot air may cause the battery interface to leak or the internal circuit short circuit to burn the mobile phone. It is recommended to last for more than 15 minutes, and then try to turn on the phone after drying it for more than 5 hours.

2) Rice quick-drying method, this method uses the principle that rice is extremely absorbent - burying the mobile phone in the rice for 24 hours is roughly equivalent to 72 hours in the air. Remove the phone that accidentally fell into the water, wipe it with the method mentioned above, and then wipe it out of the water and wipe it clean with a paper towel.

Dear, I hope it can help you. You can pay attention to me so that you can consult my pro if you have any questions in the future, can you give a thumbs up, thank you

It may cause a short circuit in the motherboard circuit board and can only be sent to the official after-sales point for repair.

It is advisable to check it out immediately.

Go to the after-sales service department of the Apple mobile phone for repair.

After wiping it clean, go to the mobile phone store to repair it.

It will be more reliable to find an official after-sales repair, but it is a bit expensive.

Summary. The water ingress of the Apple mobile phone, and the failure of the home button is caused by a short circuit in the motherboard of the mobile phone caused by water ingress. Water ingress of the mobile phone is a very serious damage to the mobile phone, and 2 hours after the water ingress the mobile phone is the best time to repair it.

The iPhone is flooded and the home button is out of order, what is the reason?

The home button failed because of the short circuit of the mobile phone motherboard caused by water ingress. Water ingress of the mobile phone is a very serious damage to the mobile phone, and the best repair time is within 2 hours after the mobile phone is touched by water.

Hope it helps.

It depends on the degree of water ingress, if it is serious, the hardware inside will be damaged, and you can remedy it according to the following measures to save the phone as much as possible.

How to fix the water in the phone:

1.Fish out the phone as soon as possible, quickly wipe the water on the surface of the phone, and remember not to try to turn on the phone.

Remove the battery quickly. This involves taking the battery, now most of the mobile phone design is integrated, the battery is not possible to be taken out by non-professionals, if you do not have rich experience in dismantling, it is recommended not to disassemble, so as not to cause greater damage.

2.Shake the phone, feel that the water in the phone is almost gone, and don't try to turn it on. At this time, use a hair dryer to maintain a non-hot temperature and blow on the place where the phone has holes, blowing 3 times for 3 minutes each time. Then start to do the drying process.

3.After 12 hours of drying, if you can try to turn on the phone at this time, if the water into the phone is not serious, it should be able to turn on normally. If your phone can turn on, then don't be too happy, you need to check the parts of your phone to see if it works.

Summary: The above operations can be summed up in two points: first, quickly power off, and cut off the power between the motherboard and the battery. Second, quickly clean up the liquid in your phone.

Hurry up and shut down, it's best to put it in the rice tank, and then take it out and turn it on after 1-2 days, maybe it can be used normally, maybe not, depending on your luck. When it has just entered the water, do not use it, it is easy to damage the motherboard by short circuit.

1.Dry your iPhone 7 with a cloth, as dry as possible, you can wipe the screen, sides and back with a cloth. Pay special attention to the power buttons, volume buttons, mute switches, speakers, microphone, and audio output jacks, and try to wipe all visible moisture as much as possible.

If possible, try using a cotton swab to absorb excess water from the audio output jack and small slits.

2.Prepare a small bag of rice and put the iphone7 into the rice bag;

3.I really can't do it, so I can only go to the after-sales store.

1.Press and hold the power button on the right side of the fuselage.

2.Press and hold the Power lock button and then press and hold the volume down button on the left.

3.When these buttons are pressed and held at the same time, the screen will turn off until the screen lights up again and the Apple logo appears.

Spend twenty or thirty yuan to wash it after the sale.

The power should be cut off immediately after the mobile phone gets into the water to prevent the mobile phone from being short-circuited. It is not recommended to use a hair dryer to dry the phone after the phone is in water, because when you blow the phone with a hair dryer, the water in the phone will move inside, which may also cause damage to the inside of the phone. If water is blown onto the screen, it may also leave water streaks on the screen.

1 Remove water and quickly wipe with a clean towel to ensure that water does not flow into the charging port, headphone jack and other sockets. If you find that the water has flowed down the connector or through the gap into the phone, carefully blow the water out with compressed air, and never blow deeper and deeper.

2. Dry processing.

You can prepare some desiccant or drying box, collect the desiccant, and seal the soaked mobile phone with the desiccant. Or put your phone under a slight heat source such as a desk lamp or spotlight to let the moisture slowly dissipate.

Wait until the phone is completely dry, try to turn it on and try to operate the functions.

If you can't turn on the machine or try to operate the fault, it is recommended to go to the manufacturer's network engineer to use professional instruments and equipment for inspection and maintenance.

If it is not long in the water, you can consider basking in the sun and blowing it with a hair dryer.

Drop the suspension button, light up the screen and use the power button, but it's a little inconvenient, it's better to change it, more than 200 yuan.

There are four solutions to the home button failure caused by water ingress in iphone6, one is to readjust the home button by pressing and holding the power button and then pressing and holding the home button; The second is to restore the home button to be sensitive through the method of external power supply; the third is to go to Apple's official retail store for repairs; The fourth is to use the iPhone's assistivetouch function to operate the screen of the mobile phone.

There are four solutions to the home button failure caused by water ingress on iphone6:

Method 2: Connect your iPhone with an external power supply, press and hold the Home button until the voice interface appears, and then remove the external power supply. The home button will be sensitive again.

Method 4: You can use the iPhone's AssistiveTouch function to operate the screen, and the specific setup steps are as follows:

Open Settings --- the universal --- accessibility feature ---AssistiveTouch in your iPhone

After entering the AssistiveTouch page, click on this function, and you can customize the menu of the quick control;

After the setting is successful, a small square white dot will appear on the screen, click on the small white dot to return to the home screen of the phone, delete background programs, screenshots, lock screen and other operations.

iphone7The home button has been changed to touch, and it is no longer the previous physical button, so it is not easy to break, and even if it is a physical button before 7, it is not easy to break, which you can rest assured.

Generally, it won't, if you're afraid of pressing it badly, turn on the small white dot service, which can reduce the frequent use of the home button.

Apple7's home button,It uses a pressure and touch unlocking scheme,It's not a physical button (although it looks like a press)So it won't involve press damage! Of course, when using the home button, you don't need to press too hard, you only need your fingerprint to touch the home button! Hope it works!

iphone7home

It is a virtual key, as long as it is not violently pressed, bumped, or dropped, it will not be damaged.

Of course, electronic products, no matter how reliable the quality, will be damaged, so there is no guarantee that they will never be damaged.

A product will have its service life. It's just a matter of time. This kind of thing was invented for people to use.

Just like the shutter buttons of your camera will break, the buttons of the previous Nokia phones will also break, and the mechanical things will always break. However, it will generally allow you to use it until the end of its life.

No, when he's bad, you'll have n phones in mind, and the designers have already thought about that.

Yes, you can break anything if you don't use it reasonably.

The home button of the 7 uses a pressure and touch response.

It's not a physical button (although it looks like it can be pressed), so there's no damage to it.

Exceptionally, it should be noted that the home button pressure does not require too much force, and the force is within a recognizable range.

There is also a need to pay attention to protect the mobile phone, dropping, touching, may cause damage to the hardware of the mobile phone.

It's no longer the previous physical button, so it's not easy to break, and even if it's a physical button before 7, it's not easy to break, which you can rest assured.