If you want to find an anti attack and anti P2P router, you can also evenly distribute the bandwidth

It's good to buy an advanced point router with management functions and divide the bandwidth evenly between each network cable Go to the market and take a look.

You can set it up.。。。 Divide your broadband evenly ... Enter the routing interface.

Limit the traffic of that person's IP to 150 for both upstream and downlink, and set it up to make his network better and bigger.

Based on the above answers, I feel that P2P has a load on the router, which will affect the network speed, and besides, the LAN protection can be installed to prevent ARP attacks, and P2P is useless. I don't know if your DHCP is on, if you open it, you may change to the IP segment of the limited network speed, so you'd better set a fixed IP for your computer, 8kbps s==1kb s, which is the conversion relationship of network speed.

Set routers to distribute the network equally: Then you can only set a speed limit.

2. Enter the correct username and password to enter the router management background.

3. We need to check the existing IP and the corresponding MAC address bar first. Click "DHCP Server" on the left, select "Client List", and write down the corresponding IP and MAC addresses displayed on the right.

5. Enter the correct corresponding MAC and IP address on the right, then select "Status" as "Effective", and then click the "Save" button to save.

6. Repeat the previous two steps until all IPs are added.

7. Click the "IP Bandwidth Control" link on the left, check the "Enable IP Bandwidth Control" checkbox on the right, and select the correct network speed below.

8. Then fill in the IP and bandwidth size to be controlled in the following rules, and also set your own computer "Guarantee minimum bandwidth", and select "Enable" for all, and then click the "Save" button to save all the settings.

You can set the network limit as you like under the P2P on one of the machines, and there is a tutorial inside.

Don't use P2P software, mainly seriously affect the overall performance of the network, because these software itself has to send a lot of network data, and your speed is not much faster after use, it is recommended that you change a router, TP-Link WR541G on the line, with bandwidth allocation function, it is not very expensive, it is about 170, it supports elastic bandwidth control, the effect is very obvious, and it does not affect the overall performance of the network.

Only enterprise routers can set a transfer rate limit on the router's ports. The average SOHO router can't, let alone split the speed evenly. Moreover, the LAN port of the SOHO router is only a switch interface).

This is not easy to distribute, so there are P2P terminators to distribute, but it is good to say hello first.

The landlord's problem is actually that his Internet speed is slow. But they don't have the permission to enter the route, and they don't want the other party to know that they are limiting the rate. In this case, offensive software such as P2P cannot be used.

Then I have a way for you to try. The first one is turned on, set your computer to a fixed IP, then install the software routing software, and set up the soft routing! In fact, just use your computer to do the route, the way to break this trick is very simple, everyone has to set the gateway as a router, but, the average person is very lazy, are assigned by DHCP, so, the use of software routing DHCP is stronger than physical routing, for example:

The routing gateway is.

Your IP is:

mask.

The gateway is the IP address of the other users (assigned by the DHCP of the soft route installed on your machine, and the rate is limited).

Although the gateway also uses software, it is relatively more hidden, I hope it will help you.

Hehe,I'm sharing the network with others right now.,The speed is 3m.,There are 5 people connected.,Didn't you have a book in it when you bought the router? The one who entered the book**,Write down the account password written on the book,Log in,Encrypt your broadband,After encryption,Even the people on your network will be disconnected,Now you go to their computer,Help them enter the password you just saved,Connected,It's not connected without your password,

How to Allocate Router Bandwidth Appropriately (Advanced Edition).

Use your IP address, username, and password (prompted on the back of the router) and enter the address bar of your browser.

DHCP Service Client List View which clients need to be controlled, and record information such as host IP addresses.

IP Bandwidth Control Add a new entry (refer to the message above to distribute evenly).

Enter the IP address and uplink and downlink bandwidth (reasonably allocated according to the requirements) Enable Save.

Fill in the data reference:

The following parameters need to be set for IP bandwidth control:

Enable IP Bandwidth Control: If enabled, the bandwidth control rule will work.

Broadband line type: If the Internet access mode is ADSL broadband Internet access, please select "ADSL line", otherwise please select "Other line".

Total uplink bandwidth: The upload speed that can be provided through the WAN port.

The IP bandwidth control entry contains the following fields:

id: indicates the first rule.

Uplink bandwidth: If the maximum upload speed allowed through the WAN port and the minimum upload speed are guaranteed, the default value is used.

Enabled: The status of the rule, indicating whether the rule takes effect.

Configuration: You can perform and delete actions on rules.

How to Allocate Router Bandwidth Appropriately (Advanced Edition).

ADSL (I haven't used this hardware) is dial-up to the Internet independently, but I estimate that your machines are also in the same LAN, with P2P, Jusheng network management and other software can be calculated according to your own calculation to allocate the bandwidth you think is fair! Hope it helps!

Enter the browser to enter the router management.

Click IP & Bandwidth. Bandwidth can be distributed equally.

According to statistics, more than 80% of network security threats come to intranet attacks, and there are currently ...... ARP attacks, skulls, DDoS, and oversized ping packets in intranetsA series of intranet attacks can cause intranet disconnection, and even attacks like ARP are difficult to detect, and antivirus software can't solve them, and they can't be **. This is also the main reason why the intranet disconnection cannot be solved after the system is reinstalled.

These intranet attacks come from the following network cards, and we only need to block them on the network cards to ensure the stability of the intranet. Network problems have to be solved by the network.

Ethernet has protocol vulnerabilities and is not good at management, which is the technical root cause of frequent network problems. Immunity wall technology is aimed at and solves this problem. Intercept and control directly on the NIC.

Its main features: the technical scope of the immune wall should be extended to the end of the network, to the lowest level of the protocol, to the entrance and exit of the external network, and to the most complete picture of the intranet, which is to hope to fully resist the network virus through the network itself, and at the same time improve the management of the business, so that the network can be controlled, managed, prevented, and considerable.

The patrol immunity network solution solves the problem of intranet attacks from the network card with immunity wall technology, dispatches a "policeman" on each network card, and directly "arrests" any intranet virus attacks at the network card, only allowing legitimate data packets to pass, and harmful data packets are directly intercepted at the network card. It also monitors the intranet without an IP, monitors the Internet access information of each PC, intercepts information, alarms information, and evaluates and blocks these problems. Solve the problem that the intranet is disconnected due to the connection of intranet ARP to other virus attacks directly from the network card, and the intranet is difficult to manage.

You don't have to change the router, install a 360 security guard, there is an ARP firewall in it, or install an ARP firewall for ColorShadow, and I've always used ColorShadow, which is very effective.

There are three ways to do this:

1.Install 360 Security Guard to defend against ARP attacks.

2.It is also possible to detect who is attacking using "antiarp software defense software".

3."Anti-P2P Terminator" is used to clear P2P Terminators running on the network.

You mean P2P Terminator?

The principle used by P2P terminator is ARP spoofing attack, which sends a large number of ARP packets to the other party through the LAN to block the corresponding network. So what else is a router for?

In this case, you just need to install an ARP firewall to get it, and there is no need to be so troublesome. Other ARP firewalls are not well understood, and the ARP firewall that comes with 360 can track the attacker's MAC address.