Why is the gas water heater always uncomfortable to wash?

If there are more than three people in the family, it is recommended to buy a 20L gas water heater, so that there will be less uncomfortable feeling of washing. Smith is a good brand.

200 square meters If two bathrooms need hot water, 16L is a little smaller, but most families take a bath based on one bathroom, so 16L can also be used. The Smith water heater is really good, I use it now, but it is more expensive than others, 16L has more than 4000, 20L has to be more expensive.

It is recommended to buy a minimum of 16L machine for two bathrooms. However, if your two bathrooms are far away, it is recommended that you install an electric water heater in the bathroom far away from the kitchen, which can reduce the loss of heat from the pipes.

As for the brand, I still buy Ariston's, my home gas and kitchen treasure, it's very good to use!

Smith's is now a brand advertising that does a good job, and you will regret it if you actually use it

16L is enough, but considering that your kitchen and bathroom are far away, you should buy a circulation system, but it is more complicated to install But it is guaranteed that you don't need to wait Turn on the faucet for two or three seconds to have hot water, the cost is relatively high Water heater 4000+, circulating pump 3000+, and some installation fees, a total of about 10000, This has to be done before decoration. But it's absolutely cool to use.

If there are a lot of people, use the tankless magnetic energy water heater directly.

The fast magnetic water heater is heated immediately when it is opened, and the temperature rises to 45 degrees in 10 seconds, saving the time of waiting for heating, and you can use as much as you want, and it does not store water and does not repeat heating, which ensures the health and comfort of hot water. Moreover, the speed magnetic water heater does not produce harmful exhaust gas, does not consume indoor oxygen, does not affect the environment, and is a pollution-free green environmental protection product, in line with the current consumption trend. This saving water and electricity not only fits the theme of the modern environmental protection and energy saving era, but also greatly facilitates people's lives.

Summary. Hello. 1. The pipeline is blocked, and there are debris blocked in the pipe, which directly affects the water heating of the water heater.

2. The pressure of the gas water heater is relatively low.

3. The mode is not set well.

Why is there no hot water when the gas water heater is washed?

Hello. 1. The pipeline is blocked, and there are debris blocked in the pipeline, which directly affects the water heating of the mega oak to the hot water positive wheel. 2. The pressure of the gas water heater is relatively low. 3. The mode is not set well.

The time on your mode is 30 minutes, isn't it?

You want to put that mode on top of the settings. Once you've set it up, you won't have to do that.

1. Can a hot water faucet release hot water? If there is, then the water heater is fine.

2. Can the hot water faucet for bathing, washing hands and washing dishes release cold water? If not, there may be a problem with the hot water pipes or faucets.

3. If the hot water faucet can release cold water, will a burst of water (a large basin of water may be placed far away from the water holder) will produce hot water? If you can, that's normal.

Fourth, if it is a water heater problem, check.

1. Is there no water outage?

2. Is there a gas outage?

3. Is the battery charged? (For fully automatic water heaters: no power outages?) 4. After turning on the hot water faucet, does the water heater have the sound of water flowing and ignition?

If the above problems cannot be ruled out, then the water heater should be repaired.

There are generally two situations when the water is not hot in a gas water heater: one is that after the water heater is ignited, the gas has been burned, but the water cannot reach the fantasy temperature; The second is that the water heater is not burning normally, the water heater is not igniting or is not igniting, you can check the reason why the gas water heater is not igniting.

The water heater has been lit on fire but the water is not hot, this situation is generally the reason for the excessive water output, you can adjust it on the knob switch of the water heater; There is also the reason for the low air pressure, the gas (natural gas, liquefied petroleum gas, coal gas) entering the burner is less than enough heat to occur, resulting in the water is not hot, you can review whether the gas source switch is fully opened, whether the gas hose has twists and turns, whether the cylinder switch is fully opened or whether the decompression flash is normal.

a. The reasons why the water of the gas water heater is not hot are:

1. There is a blockage in the gas path, such as the debris or blockage of the outlet nozzle, and some water heaters that repent of natural gas may be reformed at the time of reform, and the nozzle has not been reformed to a suitable size or the secondary pressure has not been adjusted, such as water heaters such as Rinnai and Nengyu;

2. The water-gas linkage assembly is faulty;

3. There is scale or carbon deposit in the copper pipe of the heat exchanger.

4. There may be scale in the gas filter and pressure reducing valve, and the fire channel and water channel can be liquidated.

5. Computer board failure, common for advanced machines.

The water heater water is not hot due to the above 5 reasons, and it needs to be repaired by professional staff.

b. The solution to the gas water heater water is not hot:

a. Displacement of occlusion at the place;

b. Replace the water ball valve;

c. Clean the vacuum tube;

d. Scrub the surface of the vacuum tube clean;

e. Replace large-capacity water heaters or install electric heating systems;

Causes and maintenance methods: 1. The gas cannot enter the water heater smoothly due to the blockage of the air inlet filter, if the blockage is not serious, then it may take many times to fire, and if the blockage is serious, it will not be able to ignite. The intake air filter needs to be cleaned;

2. The water pressure is unstable. If the water heater has a bit of fire and sparks, but it burns out quickly, then the water pressure is unstable. You can buy a household booster pump to enhance the water pressure; Other reasons and maintenance methods are as follows:

3. It may be that the filter screen at the inlet is scaled and blocked, or it may be the scaling of the water valve, which will lead to unsmooth ignition. It is necessary to carry out a full range of descaling and cleaning of the water heater pipes;

4. There is a problem with the power supply, although the gas water heater relies on gas energy, but it also needs to use a battery when ignition, check whether the AC power plug indicator is on, if it is not on, it means that there is a problem with the power supply. Circuit overhaul is required;

5. The solenoid valve is not opened, and the coil is broken. Most of the resistance of the solenoid valve coil should be about 100W, and the resistance value is infinite when the burn-out open circuit is burned, and the solenoid valve needs to be replaced;

6. The voltage provided by the computer board to the solenoid valve is too small to make it open the valve. Use a multimeter to measure whether the voltage of the solenoid valve is around DC20V. Check whether the 24 volt output voltage of the transformer is normal. If it is not normal, replace the computer board or transformer.

This one is suitable for most gas water heater models such as Haier JSQ25-13UTS.