How to remove the filter of the Philips juicer HR1836 5

Hold the filter with your index finger and thumb to remove it.

Due to the requirements of the juicer function, the knife mesh itself is relatively tight, when taking the filter screen, the index finger and thumb of both hands hold the filter screen, and the other fingers hold the pomace box, and the knife mesh can be taken out vertically upward.

This juicer is relatively small, the juicer filter is a little different from the one on the market, the big cup mouth is down, but the working principle is the same, as long as it is pulled up normally (there should be no problem of card protection), it can be disassembled, the following picture is the structure of this juicer, this is the pertinence of Xinpeng hardware xapng, I hope it will help you

How to use: A juicer can only function when all parts are properly assembled and the lid is locked in the correct position with clamps.

Wash the fruit or vegetables and cut them to a size that fits in the feed tube.

Make sure the juice cup is placed under the spout.

Twist the control to set 1 (low speed) or 2 (normal speed).

Speed 1: Ideal for soft fruits and vegetables such as watermelon, grapes, tomatoes, cucumbers and raspberries.

Speed 2: Suitable for all types of fruits and vegetables.

Place the pre-cut fruits and vegetables into the feed tube, then use the feed wand to gently push the fruits and vegetables down into the rotating strainer.

Do not push the fruit and vegetables with the feed stick too hard, as this will affect the juicing effect and may even stop the strainer from turning.

Do not put fingers or other items in the feed tube.

Once all the fruits and vegetables have been processed and the juice has stopped flowing, turn the juicer off and wait for the strainer to stop turning.

Place the foam separator in the juice jug and close the lid of the jug. This way, when the juice is poured out, the foam will remain in the jug.

Note: If you want to keep the juice foam, do not use the foam dispersant.

Cleaning method: Never clean with steel wool, corrosive detergents, or aggressive liquids such as alcohol, gasoline, or acetone.

Clean it immediately after use and you'll be able to get your juicer clean with ease.

Turn off the power of this product, plug it in, and wait for the filter to stop spinning.

Remove the dirty parts from the motor mount.

Steps to disassemble the juicer: Remove the pomace trough Remove the pusher lever Loosen the clasp Remove the cover.

Remove the juice collector along with the strainer.

Wash these parts in lukewarm water with a cleaning brush and dishwashing detergent, then rinse under the tap.

Note: All detachable accessories are dishwasher safe and should be placed on the upper level of the dishwasher, confirm that these accessories are kept away from heat sources.

Clean the motor mount with a damp cloth.

Do not submerge the motor seat in water or rinse with a tap.

Precautions. Do not immerse the motor holder in water or other liquids, and do not rinse under the faucet.

Before plugging in, please check whether the voltage marked on the electrical device matches the voltage used locally.

Do not use if plugs, wires, or other components are damaged.

If the wires are damaged, they must be replaced by Philips, an authorized Philips service center, or a technician with the same qualifications to avoid danger.

For safety reasons, without supervision and proper instructions, it is not suitable for children and any person with physical, perceptual, or mental impairment, or who lacks experience and knowledge in use.

Do not allow children to use this product or use it as a toy.

Do not leave the product unattended.

Discontinue use if you notice any scratches or damage on the filter.

Do not put your fingers or other objects into the feed pipe while running. Only feed bars can be used in this case.

Do not touch the small blade at the bottom of the strainer as the blade is very sharp.

Resources.

Summary. Why can't the filter of the Philips juicer come down?

Hope my answer is helpful to you.

How to dismantle in 1871.

The process is the same, and then you'd better look at the instructions to understand the assembly part before dismantling.

Summary. Philips HR1855 juicer disassembly and cleaning method: 1. First of all, the machine must be turned off first, and then the slag storage tank can be dismantled and cleaned.

2. The juicer is a kind of machine that can quickly squeeze fruits and vegetables into vegetable juice, which can be used at home. Disassemble the buckles on both sides, remove the upper cover, and pick up the knife net directly upwards.

Hello, dear, how to disassemble the Philips juicer HR1855**First unplug the juicer plug and wait for the juicer to cool down, remove the used accessories and various parts, and then rent it in warm water with detergent for cleaning. Finally, rinse all accessories and parts under the tap. Be careful not to slow down the use of steel wire, tung lint, abrasive detergents or corrosive liquids.

How to remove. Philips HR1855 juicer dismantling and washing method: 1. First of all, the machine must be turned off first, and then the slag storage tank can be dismantled and cleaned in the spring.

2. The juicer is a kind of machine that can quickly squeeze fruits and vegetables into vegetable juice, which can be used at home. Disassemble the buckles on both sides, remove the upper cover, and pick up the knife net straight up.

Summary. Philips Viva Collection Juicer HR1855 cleaning, disassembly and installation steps schematic diagram:

Ask about custom messages].

Philips Philips + HR1861 00 juicer high juice yield residue separation large feeding port HR1866 how to disassemble.

Hello dear and happy to answer your <>

Kiss Philips Philips + HR1861 00 Juicer High Juice Yield Residue Separation Large Feeding Port HR1866 How to disassemble 1, first remove the cover to disassemble the juicer, first need to take off the handle, and then remove the cover, there is also a knife net when the same Liang is buried, and it must be lifted up in the vertical direction, and it must not be dragged hard, otherwise it is easy to damage. 2. To remove the base, you need to unscrew the screws of the base directly, and then you can remove the base. And if there is a problem of getting stuck, you must not apply brute force.

You can press the reverse button once, and then disassemble it in the correct and correct way. 3. Finally, the filter screen needs to be disassembled, which can be directly rotated in the counterclockwise direction, and it can be taken down by straight liquid cracking. Generally speaking, fine nylon is chosen, which can be placed directly under warm water and scrubbed clean with a brush.

I hope this service can help you, you can click on my avatar to follow me, and if you have any questions in the future, you can consult me again, and look forward to serving you again. Wishing you well; Happy life, everything goes well [warm] [warm].

How to disassemble the juicer is detailed in the instruction manual.

The cleaning of the Philips HR2828 juicer is best to wash it when it is used, otherwise it is difficult to clean.

Add 1 3 warm water and dish soap to the stirring container of the juicer, plug in the power and blend for 30 seconds, then rinse with clean water.

Wash the back of the filter with gauze while flushing with the faucet, so it is easy to wash.

The clogged fiber strip at the cutter head can be slowly pulled out according to the direction it is around, do not use too much force, and the other can be brushed with steel wool balls, but do not use too much force to avoid damaging the cutter head.

Cover the 3 4 of the faucet with the index finger of one hand to form a "water pressure gun" to flush away most of the pulp residue, and then brush the edge with a toothbrush a few times.

When cleaning the juicer, add a small half cup of water and add some broken eggshells, stir for two minutes, and you will find that the juicer is as bright as new, and it works better with vinegar and eggshells.