As soon as I turn on the phone, I m going to press F1 to go in, what s going on

After turning on the computer or restarting the computer, press the "DEL" key in time to enter the BIOS settings interface, click a few options casually, but don't modify, stay in the BIOS environment for about a minute, BIOS will automatically help you set up, press the ESC key, F10 key, Y key, enter to store and exit the settings.

How about trying it out? No, use the following method:

1. Restore or optimize BIOS settings.

After turning on the computer or restarting the computer, press the "DEL" key in time to enter the BIOS settings interface, award

Load BIOS defaults, this option is used to load the BIOS initial settings to determine the scope of the failure.

Load Oprimum Settings, which are optimized settings for the factory BIOS.

or AML Load BIOS Setup Defaults, which is used to load the initial BIOS settings.

Load High Performance Defaults, which is used to load BIOS optimization settings.

After selecting the default or optimized value with the keyboard arrow keys, press Esc, F10, Y, press Enter, Save and exit the setting.

2. Turn off the floppy drive.

Reboot, press del into the BIOS, find the standard CMOS setup, press enter in the open interface, change drive A: and driveb: to none, set Floopy 3 (floppy drive) to disable, press ESC, F10, Y, press enter to save and exit the settings.

3. The floppy drive is not detected when it is turned on.

Reboot, press Del into the BIOS, find the Advanced BIOS Setup, press Enter in the open interface, set "Boot Up Floppy Seek", set to "Disabled", press ESC, F10, Y, press Enter to save and exit the settings.

4. Set the hard disk as the first boot. Reboot, press del to enter the BIOS, find the Advanced BIOS Features (advanced BIOS parameter settings) press enter to enter the Advanced BIOS Features interface, set the First Boot Device to HDD-O (hard disk boot), press the ESC key, F10 key, Y key, press Enter to save and exit the settings.

5. Check and replace the motherboard battery.

There is an error in your computer's BOIS settings. Or the computer battery is dead.

You can go into the BOIS and see if the floppy drive is open.

Reboot and press delete on your keyboard to enter a blue screen interface and look for a blue screen that should be.

Change this to the first one called d or something, which means off. When you're done, press F10 and then select the first one. It will automatically restart.

It should be done, if it doesn't work, it will be explained. The battery is dead. Go fix the computer's ** and change it.

The CMOS battery is dead. Open the case, find one of the coin cell batteries on the motherboard, and remove it for a new one.

It's your CMOS that's doing the trick, you just go into the CMOS, just look at the things inside, don't change it, and save it when it comes out.

The motherboard is out of power, and the time cannot be saved, it may be that there is a problem with the battery.

Go into the BIOS and set it, and you won't have to press F1 when the setting is set! It is best to choose only the health disk error to report the error.

Is it an old machine? Is it that the floppy drive A: disk is not shielded?

Computer Fault Description:

It will be prompted every time it is turned on.

And you must press the shortcut key F1 before the computer can start normally.

Reasons and solutions for secondary failures:

1. The battery on the motherboard is dead.

Solution: Replace the motherboard battery.

2. You have set up the floppy drive to start, but there is a problem with your floppy drive.

Solution: A. Press del to enter the BIOS at boot, boot up the boot sequence, and turn off the floppy drive to boot.

b. Turn off the detection function of the floppy drive when it is turned on

Start the computer and press the [DEL] button to enter the main BIOS settings interface.

Select "Advanced."

biosfeatures", press the enter key to enter;

Add "boot

upfloppy

seek" is set to "disabled", so that the boot software detection function can be turned off, and there is no need to press F1 to start it in the future.