ADSL can be connected, but the route is not

The campus network is restricted.

The most direct way is to install a switch and use a computer as the host.

Shared Internet access. Sure point is that when other computers want to go online, the host cannot be turned off.

As for whether you must use the router, you can only see if your campus network dial-up account is encrypted.

Once encrypted, try to find the correct account.

If you still can't, you can only use the above method.

After connecting the router, if you want to surf the Internet, you need to dial through the router.

The IP address of the router is generally OR.

Enter the IP in the address bar of the Internet Explorer, the username and password are set step by step in the admin setting wizard, and enter the Internet access and password according to the prompts.

Finally, dial in with the router, and all computers connected to the LAN port can access the Internet at the same time.

If it's adsl, just choose the dial-up item in the route, fill in the username and password, this I believe you should be, so you have to see if you have obtained the IP address in the running state, if there is, it means that there is no problem, theoretically it should be able to get on, if not, it has been displayed in the connection, some are linking, anyway, that's what it means, and in this case you don't use the router and you can dial through, I think you can try to restart the router, Soft reboot and hard reboot are OK, if it still doesn't work you just borrow a router and try it, if it can be on, it means your router is hanging.

One: Some schools buy cards that can't be dialed up with routers, which is to cheat students out of more money. Our school used to be like this! And then we bought cards from other schools and dialed them so we could use the route.

Two: There is a problem with the routing settings!

If the router is set, reset the route, refer to the route instructions and reset.

Reset the router to factory values and then set it up. Look.

Set the IP address to be automatically obtained in the local connection.

Please plug the network cable into the sub-socket and do not plug in the main entrance!

Select the Setup Wizard -- Next -- Adsl Virtual Dialing -- Next -- Fill in your broadband Internet account and password -- Next .

After doing a good job, you can basically go online!

No more broadband dial-up! Turn on the computer and go directly to the Internet.

You try to restore the router to a factory setting, you have to make sure that if you remove the router only with the cat can be on, and then see if the WAN port light is on? Check if there is a problem with the network cable connecting to the WAN port, sometimes the line sequence of the network cable is wrong, and the light of the WAN port is also on.

That piece of running state sees that there is nothing in the WAN port.

If you don't get the IP address from the WAN port Zhuang, you can see if it is the network card port on MDoen, and the network cable is connected to the WAN port of 841n If it is connected to the WAN port, you should take a closer look at the WAN port settings in the router settings, whether it is set to PPPOE dial-up Internet access, and whether the account number and password are correct, please check the above information

After setting up the telecom account in the bar, select Restart in the last column on the right. You don't plug in the router and use the computer first to see if you can surf the Internet.

It's probably a matter of the thread that you've experimented with before.

I don't know which router you use, read the manual, each router has settings, according to the manual, the user name, and other corresponding data can be set.

Here's why:

There is a problem with the quality of the router. When connecting to the Internet, the router is broken, and then the computer cannot access the Internet. This necessitates the purchase of a new router.

There's a problem with one of your computer's hardware. At this time, you can go to a repair shop to repair it. If the computer is within the free warranty period, it can also be guaranteed free of charge.

Workaround: Connect directly to the router.

Set Router Dialing Method:

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoE Dialing] (some are ADSL dialing), enter the username and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Question: I asked why I couldn't dial up the internet.

Okay, wait a minute.

Cause: You need to manually set up dial-up Internet access.

Ask how to set it up.

Answer 1: In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL dialing), enter the Internet user name and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Is it too much network cable or the router is used for too long, I also encountered my situation, change a router, you can connect.

Let me help you break it down.

First of all, do you need a cat to surf the Internet or not, if there is a cat, you use the Internet alone and use the same network cable with the router, this is mainly to check the network cable, if you are sure that the network cable is easy to use, then say the second point.

Second: you can dial up the Internet normally to prove that your network and computer are fine, there are other hardware left, check whether your routing settings are normal, the settings are normal and this situation, just try to change the route, if multiple routes are this problem proves to be other problems.

So my method is the elimination method, which is to detect one by one.

The dial-up connection is fine, but the connection through the router may not be connected to the Internet for the following reasons:

1. The Internet account and password are incorrect;

2. There is a problem with the router dialing function;

3. There is a problem with the router interface;

4. There is a problem with the router itself;

5. There is a problem with broadband.

Solution: 1. Log in to the router and re-enter the Internet account and password;

2. You can log in to other broadband to test the router dial-up function;

3. Replace a router connection port (here it mainly refers to the computer through the wired Internet, replace a [LAN socket]);

4. Change a router and try to connect to the Internet;

5. Call the broadband operator and ask if it is a broadband problem that causes you to be unable to access the Internet.

If the budget is sufficient, you can ask us!

If the router is connected, the broadband will not be connected, which is definitely a judgment!

Because the virtual dialing of broadband has taken over the router; The main reasons why the average home uses a router are:

1. The virtual dialing is taken over by the router, and you can basically access the Internet when you turn it on.

2. You can connect multiple computers to the Internet through the router (except for the setting of video broadband block) If you have to connect to the router, please use a browser to enter the router first: enter the router at the bottom of the ** column), and some routers are exceptions! After entering the router, the Chinese prompt operation, very simple!

You can try it by making dates first!

Hello! If you are sure that the route and MD are connected to the computer, that is, you are not set up, first you have to open the hand defeat in the IE browser, enter it in the address bar and then enter the selection settings, select the first item, and then enter the Internet and password, after the OK, you can set it up, after setting it, you select the home page to see if it is connected, if you don't connect, you will connect at that point, Bi Kai trembling local connection on the computer, then you don't want to set the IP because it is automatic, and you don't need to dial up the Internet with the route, you can go directly, You take a good look at the manual, if it's not right, I'm asking, my Sun Nian is on a mobile phone.

Connect the desktop computer to the router first, plug it in, and then enter it in the IE browser, some routers are the front one, and some routers are the back one), set it step by step according to the router manual, and you can get on it after the setup is completed. After the desktop computer is on, the notebook searches for the router through the wireless link, and the no pants Huaicha line link shows that it is connected, you can get on, don't click on the broadband link, as long as you turn on the router in the future, you can access the Internet again on the computer, whether it is a desktop computer or a notebook,

Ah yes, after the broadband is connected to the router and then divided and erected to your computer, the router has to be set up, is it set?

Of course, the broadband connection can't be connected, and the router will help you connect the fiber branch as soon as possible, so you can go directly to the Internet when you turn it on.

Use the router is the computer is not dialed by the car, the router will help you dial the closed branch, the router dials up to the computer, as long as the local connection is connected, you can access the Internet with the hall.