How to solve the problem of making handmade soap with bubbles The more detailed the better, 20 point

Hello, I am the small fish in the spring soap fang, 1Soap.

Do I need to stir all the time to heat with water? Answer: It is best not to, because bubbles will be produced when stirring, especially the transparent soap base, which will be cloudy and unable to make crystal clear soap, such as soap in soap, photo soap, etc. 2

When to add essential oils or soap colorants? Is it necessary to wait for the soap to leave the **, add it after cooling, or add essential oil or color solution when it is heating? A:

The color (color water, color paste) is recommended to be boiled with the soap base, as long as it is mixed lightly a few times, it will be mixed well, if it is a flavor, it can be mixed with the soap base, but the temperature of the essential oil is too high, and the effect will be destroyed 3Can I continue stirring after leaving **? A:

Remove from heat. It should be said that after heating over water, after the soap base melts, essential oils are added at this time, and it can be mixed slowly so that bubbles will not be produced, if bubbles are produced, you can stand for half a minute to one minute to let the bubbles float on the surface, and then use a spoon to remove the upper film, so that the soap will be very beautiful and clear. If you only spray with alcohol, you can only eliminate the bubbles on the surface, and the small bubbles in the soap will not disappear, but unless you stir very hard, there will not be too many bubbles4

Do I need to cool down before I can enter the mold? Answer: depending on the style you make, if it is soap in soap, and the soap body in the soap is small, I am afraid that the soap liquid will melt the small soap body if it is too hot, my personal experience, will be put for a little 30-60 seconds, and then operate (the same upper layer will produce a film, after removing the operation) 5

If you want to add flower petals, should the petals be sprinkled in the mold or in the soap first? Answer: The effect is different, you can try, but it should not be boiled with soap base Oh Please refer to the above, if you have any questions, please leave a message See more answers

Bubbles are a very common problem when making handmade soap, and here are some ways to fix it:

1.After the soap is heated and melted, a small amount of alcohol can be added to help defoam.

2.After the soap base melts, it needs to wait for it to cool down completely before it can be put into the mold, otherwise bubbles will be generated.

3.Once the soap base is in the mold, light vibration can be used to help eliminate air bubbles.

4.Once the soap base is in the mold, it can be frozen or refrigerated to help eliminate air bubbles.

5.After the soap base is molded, it can be left to allow the bubbles to rise naturally to the surface and then removed with a spoon.

6.Once the soap base is melted, it needs to be stirred well with an electric mixer to help eliminate air bubbles.

7.After the soap base is put into the mold, it can be deaerated by a vacuum machine, which can eliminate air bubbles.

8.After the soap base is put into the mold, it can be stirred by hand to allow the bubbles to rise naturally to the surface, and then remove them with a spoon.

9.Once the soap base has melted, it needs to be filtered through a strainer to remove impurities and bubbles.

10.After the soap base is molded, it can be heated to allow the bubbles to rise naturally to the surface, and then removed with a spoon.

11.Once the soap base has melted, a small amount of milk can be added, which can help eliminate the bubbles.

12.Once the soap base has melted, a small amount of honey can be added to help eliminate bubbles.

13.Once the soap base has melted, a small amount of oat flour can be added to help eliminate bubbles.

14.After the soap base is put into the mold, the air bubbles can be shaken to rise naturally to the surface, and then removed with a spoon.

15.Once the soap base is melted, it needs to be stirred well with an electric mixer to help eliminate air bubbles.

16.After the soap base is put into the mold, it can be deaerated by a vacuum machine, which can eliminate air bubbles.

17.After the soap base is put into the mold, it can be stirred by hand to allow the bubbles to rise naturally to the surface, and then remove them with a spoon.

18.Once the soap base has melted, it needs to be filtered through a strainer to remove impurities and bubbles.

19.After the soap base is molded, it can be heated to allow the bubbles to rise naturally to the surface, and then removed with a spoon.

1. Mix the grease, put the grease in the soap recipe into a stainless steel pot, and heat it in a waterproof or induction cooker.

2. Dissolve sodium hydroxide, the container must be resistant to acid and alkali, be sure to stir the sodium hydroxide until completely dissolved, the gas generated when dissolved is corrosive, avoid inhalation.

3. After heating through water, measure the oil temperature.

4. Measure the temperature of the lye.

5. Oil-alkali fusion, when the temperature of oil and alkaline water is similar, it can be mixed, and it must be stirred continuously for the first 20 minutes.

6. Stir, you can enter the mold, stir until the soap is thick, that is, use the stirrer to scratch the soap, and its lines will stay on the soap.

7. Milk cartons, pudding boxes, and tofu boxes can be used as soap molds, and the box body is slightly elastic and easy to demold.

8. Cover with plastic wrap to avoid the production of soap powder.

9. Put it into the styrofoam box for insulation.

10. Cover the lid of the Styrofoam box, wait for the soap liquid to be saponified, and the film can be removed after 24 hours.

11. Cut soap, dry soap, the place must be ventilated, cool, avoid direct sunlight, after aging, the pH value of the pH value is below 9, and the hand soap can be used.

The first is natural oils and lye, which are necessities and can be said to be the main ingredients of soap.

After that, it's time to add other accessories according to your personal preferences. For example, milk, essential oils, flavors, flowers and herbs, traditional Chinese medicine, etc.

Adding different excipients will give the handmade soap a faint fragrance and different skin care effects.

1.It is a handmade soap and has a short demoulding time, so it is necessary to stay in the film for a longer time. Generally, it can be demolded in 24 hours, and the soap with finger shed lasts longer. For example, the soap of castor oil should be at least 48 hours, and it doesn't matter if it is left for a long time.

2.At the same time, the overall hand-only ins value of the oil used below is calculated. The higher the ins value, the harder it is. Generally, the hardness (INS value) of handmade soap is recommended to be between 120-170, which is considered to be the ideal hardness.

Prepare the mold first, then take out the milk and pour it into the cup, then add the caustic soda, add it several times and keep stirring until the alkali particles are completely dissolved, then add grease to the cup several times and stir well, and finally pour the prepared solution into the mold, and after two days, it will be demolded and made into handmade products.

1.Pure natural, handmade soap is made of 100% natural vegetable oil, mild ingredients, rich and delicate foam, can be thoroughly cleaned**, no chemical ingredients are added. Long-term use will not cause burden, harm and allergies, and the more you use, the healthier it is.

2.Moisturizing and moisturizing, glycerin and soap will be produced after oil saponification; However, most soap and shower gel manufacturers extract glycerin from soap and use it as other high-end cosmetics and skin care products. Glycerin is an indispensable moisturizing ingredient in cosmetics and skincare products.

This soap does not extract glycerin by hand, and the proportion of glycerol is up to 25%. It has an excellent moisturizing and water-locking effect, can fully moisturize the skin, and has a gentle nature, so it will not feel dry and tight after use.

3.Rich in nutrients, handmade soaps are made in the cold way. The general temperature is between 40-60 degrees Celsius, and the production process is not continuously heated, which will not destroy the nutrients in the original vegetable oil, and various vitamins and essential oil components will also be retained.

The way to make handmade soap is to buy the soap base online, add your favorite flavor or some other ingredients, wait for it to melt and pour it into the mold, and then slowly solidify and agglomerate.

The production method of handmade soap is to buy the soap base that has been made on the face of the city, and add your own materials to make it, very good handmade soap, if it is soft, it may be because you are demoulding too early, it is recommended to put it back into the mold when you are bright and wait for a while.

In this case, you can adjust the formula of the hand cover crack soap, add some hard grease to it, and prolong its demoulding time, so that the hardness of the handmade soap can be higher.

The specific production method is relatively simple.

1.Choose the recipe you want to make. Keep a good note of the various greases and tools you need.

2.Weigh the sodium hydroxide and water needed according to the recipe and put it in a beaker for later use.

3.Weigh all kinds of grease needed. If it is solidified, it can be heated in water to dissolve.

4.Set the temperature of fusion, fuse the lye with the grease, and stir constantly. The process takes about an hour.

Finally, it reaches a thick state, and if you choose to add extra fat and essential oils, you can add it here. Finally pour into molds. Keep warm.

5.It can be demolded in about 24 hours.

6.Cut, dry. It can be used in about 4-7 weeks.

The specific steps of the recipe are based on the recipe, and there are slight changes. For example, if you choose to make milk soap, the steps after melting alkali and entering the mold are different, and you need to depend on the actual situation. But that's about it.

Hello! The process of making soap by hand is: the soap base --- is added with biqing effect ingredients--- formed --- matured.

Make lye. Cool the lye water. Melt the grease and mix in proportion.

Pour the lye into the grease and mix to set up. Stir until trace Add essential oils and additives. Pour into the mold.

Keep warm for 24 hours before cutting. After that, it is left to dry for 1-6 months.

Hope it helps!

Benefit 1 of handmade soap DIY: good moisturizing and strong cleaning power. Handmade soap contains natural glycerin, which is super moisturizing and moisturizing, and has strong cleansing power without damaging the stratum corneum of the skin.

This is because the ingredient of glycerin can form a protective film on the surface of ** when cleaning dirt, which has the effect of caring for the skin. In contrast, in the process of saponification, the soap will extract glycerin, resulting in a very dry skin after washing.

The benefits of handmade soap DIY 2: retain nutrients, made at low temperature, can maximize the retention of essential oils and nutrients in other ingredients. And it won't destroy the structure of natural vitamins, so handmade soap is a good skin care product.

It is a convenient way to take care of your skin when the pores of the whole body are steamed with warm water, and you can take care of your skin by cleaning it with handmade soap.