Someone else comes into my CS1 6 server and I ll get stuck

Updated on technology 2024-04-27
6 answers
  1. Anonymous users2024-02-08

    OpenGL does not support the issue.

    This is also very common, and there is usually a hint like this: the selected OpenGL mode is not supporlted by video card......

    Regarding the problem of OpenGL not being supported, it is more complicated, and some solutions are listed as follows:

    1. Forced settings, some graphics cards always remind you that you don't support opengl, ignore him, continue to set up, you can use it.

    Usually this solves the problem, but it doesn't work, please.

    4. Manual installation or msopengl (address.

    Latest full version of glsetup (released on April 13, 2001.)

    for win9x)

    5. If you still can't solve the problem, maybe your graphics card doesn't support it, please use GLLodirect, (reduce hardware requirements, emulate OpenGL).

    Another: There is an upgrade of the latest version of OpenGL, you can try it.

    In the actual problem solving, it is found that there are still some people who can't solve it, most of them are gf2mx400 and gf2mx440 graphics cards.

    Here are the solutions you can give a try:

    Right-click on the desktop --Properties--Settings--Advanced, click -GF2MX and click OpenGL Settings in the left border to adjust

    2. Turn on "Disable Support for CPU Enhancement Instruction Set".

    3. Default color depth for textures: always use 16bpp

    4. Buffer Flip Mode: Use bit block transfer.

    5. V-sync: always off.

    6. Anisotropic filtering: disabled.

    7. Maximum usage: 14

    Among them: 1,2,4 The effect is not very obvious, and 3 is important for WinXP users.

    5,6 It is highly recommended to change it.

  2. Anonymous users2024-02-07

    It's a problem of network speed, not a problem of the machine, you just need to have a good network or someone else's slow network, you go and add someone else's best!

  3. Anonymous users2024-02-06

    I don't think your machine's configuration is high enough, and the memory is not large enough.

  4. Anonymous users2024-02-05

    Be content! It's a problem for others to brush out the server I built!

  5. Anonymous users2024-02-04

    There are several issues with building a host card.

    1. If you surf the Internet at home, it is your home network speed is not good, and 2m can't bring more than 8 people to the network, of course, if your home is 10m community, you can do it.

    2. If you are in an Internet café or a 10m community to build a network or a repaid card, then you can see if they have an Internet speed higher than 100, and some will kick it.

    3. Someone who cheats will also get stuck.

  6. Anonymous users2024-02-03

    It could be that the ping of the server you are entering is too high, or it may be your own fault.

    Also, I originally wrote a post on this issue, so I'll turn it around and give it to LZ for reference.

    First of all, you have to determine whether your network is unblocked,If you use a single line,1m is enough,If it's co-linear with other people,When others are**Or watch network TV,You will get stuck or jump ping(Of course, you have to make sure that you don't**,You don't watch network TV,There's a little trick here,That is, lz will find that the network TV is turned off,But it will also jump,Because the process and its accelerator are not closed,At this time, open the optimization master,Or360, I'm using 360 process management and turn off all the accelerators).

    Then it depends on your computer configuration, 1GB of RAM is recommended, and a graphics card of more than 7300 is recommended. Combined with their own experience to talk about virtual memory,At that time, I just bought a computer when I played very comfortable,But after a long time,There are more things,The system will prompt that my virtual memory is insufficient,I think how can my 1GB of memory be insufficient,Still don't care about him,As a result, CS is stuck and jumped,Later, I learned that when I first bought a computer, the virtual memory of the C disk was only 215MB,I changed it to 1500MB,It's much better (Method:My Computer - Properties - Advanced - Performance Settings - Advanced (Virtual Memory Change) If your RAM is 1GB, set the maximum value of the C drive to 1500, and the initial value is 1400, which is basically a double of your memory, and so on.

    Then apply, OK.

    Finally hope mine is helpful to lz.

Related questions
How to set up a CS1 6 server
7 answers2024-04-27

Very simple. Of course, you can see your own server.

But the IP of your server is the IP of the private network....That is, it starts with 292. >>>More

CS1 6 server cannot add 100
6 answers2024-04-27

1. The server may not be running.

2. Maybe your CS is tuned to LAN mode, if this is the case, you can't find the server on the Internet, please open the console and enter: sv lan 0 >>>More

How do you set yourself as OP in CS1 6 Internet Battle Server?
18 answers2024-04-27

First, you can build your own room, so that you yourself are OP. If you enter someone else's room, you will need to enter some commands into the console to make yourself op.A more professional approach: >>>More

CS1 5 server ip, CS1 6 know how to enter the server?
6 answers2024-04-27

Chongqing 370: 27015 CQF-4 no-cdke 0of20

Chongqing 299103 :27018 CQHC-feifan S 0of22 >>>More

How to set up a CS server, and what do you need to set up a CS server?
8 answers2024-04-27

1、You have to find the right version,You have to bring a new notepad to take the previous sentence as the content,Save as,Save the type to select all,Remember,Then,The file name is saved to the root directory of cs。 3. Run it directly. In step 2, 27015 is the port, sv lan1 is the local area network, change 1 to 0 is the Internet, de dust2 is the map name, and maxplayers10 is the maximum player of 10 people. >>>More