What should I do if there is no local connection, there is no local connection in the network?

Your old network card doesn't work.,The new network card hasn't been found.,You can find it when you scan it.,If you haven't found it, press it again.。

The local connection is gone, but you can still surf the Internet normally Reason: Since the local connection is gone, you can still surf the Internet normally, which means that there is no problem with the computer hardware. But what is the reason for this problem?

Pepsi.com believes that most of the reasons are due to people accidentally connecting to the "local connection" when using the computer...

The local connection is gone, and the Internet cannot be accessed normally Reason: In this case, it may be that the local connection is disabled due to accident or virus damage. In other words, the NIC may be disabled, and of course there is a possibility that the NIC driver is not.

There is no local connection in the network, only mobile phone data is fine.

If you can't access the Internet normally and the local connection is gone, consider the driver first, because the network card driver is not installed or corrupted, which may cause the local connection to be lost.

Motherboard wiring? You can't just unplug the motherboard power cord, do you? According to your description, it is very likely that the network card was loosened when you unplugged the cable, so you can reinsert it like a memory module

What operating system is yours?

Take WinXP as an example, WinKey+R, enter and press Enter, check whether the service network connections are disabled, and if the ban is changed to automatic or manual and enabled, the system may need to be restarted.

In general, it is OK to reseat the NIC and then reinstall the system. Otherwise, the network card is faulty, and the network card needs to be replaced! Good luck!

1. After opening the online neighbor, click "View Network Connection" in the left bar to see.

2. If there is no "Local Connection" icon in the taskbar, after opening "Local Connection", click Properties, and check "Show icon in notification area after connection" to display the icon in the taskbar.

Start -- Settings -- Network connection -- Local connection (broadband connection).

If you can't connect, check whether the IP address is set wrong, and generally get it automatically.

Tell you, first look at the device manager there, the local network card is not an exclamation mark! If so, it means that the network card is not driven normally, and then open the chassis to check.

First of all, your question description is incomplete, is it a desktop or a laptop? In my opinion, it is more likely that the network card has a light and is a desktop, so if it is not a nonsense to install a wireless network card to access the Internet, it should not be a problem of disabling network-related services, and at this time, there should be two network adapters, see if one of them is disabled. If "what wires on the motherboard are not connected" refers to soldering, then you can still successfully install the driver is really good, and you don't need to ask here; If it doesn't refer to soldering but simple unplugging, then this sentence "I don't know if it's the motherboard and what wire is not connected" is nonsense, because your network card light is on.

It is recommended to sort out the clues in detail.

For a different version of the system installation, it is recommended to install the pure version, which may be a conflict between the integrated driver and the hardware.

I just need to create a new local connection with the network connection in my computer.

In Device Manager, right-click to scan to detect hardware changes.

If there is no unknown device or local connection, there is a problem with the motherboard.

NIC driver.

You can also create a local connection.

Online Neighbors - All Internet Connections - Create a connection to the Internet - Just select the Internet Broadband that requires a password.

XP system network neighbor - attributes, win7 system to create a new connection.

It may be that the wire inside the network socket is connected incorrectly, and the eight-core wire is easy to be connected incorrectly.

Take a look at whether the local network card in the computer's Properties Device Manager is not enabled.

You can try.

Click - Network Neighbor - View Network Connection - Create a New Connection - and the New Connection Wizard appears, -Next - Network Connection Type, Connect to the Internet - Next - The following is selected according to your own situation, I use the second type to enter the account password.

Hope it helps. Thanks, here's my little advice.

Because you don't have the local NIC driver installed, you can use software such as Driver Life to update the local NIC driver.

Install the driver life, and follow the prompts to update the driver.

Comfortable Canton Fair surface can come out.