There is no local connection after the computer is reinstalled, and there is no local connection sol

Updated on technology 2024-02-08
8 answers
  1. Anonymous users2024-02-05

    First: The local connection in the lower right corner of the taskbar is gone, the user can surf the Internet normally, but there is no local connection icon in the taskbar, this situation is easier to solve, first, right-click "Internet Neighbors" - select "Properties" - find "Local Connection" in the open "Network Connection" - right-click "Network Connection" - select "Properties" - find "Display icon in the notification area after connection" at the bottom of the pop-up "Local Connection" property, tick it in front of it - > click" OK "Exit, now see if there is already a local connection icon in the bottom right corner of the taskbar;

    The second type: there is no local connection in the network connection, the computer can not dial up, can not access the Internet, right-click "Network Connection" and select "Properties", there is no local connection icon in the pop-up "Network Connection" folder, similar situations are relatively complicated to deal with, we judge the cause of the failure one by one, and are trying to solve it;

    1.Right-click on "My Computer" and select "Properties" - select the "Hardware" tab in the pop-up "System Properties" - > click on "Device Manager" - check in the pop-up "Device Manager" to see if there is an exclamation mark in front of "Network Adapter"! , or is there a question mark in front of the "network controller"?

    If a question mark or exclamation mark appears, it means that the NIC driver is abnormal or the NIC driver is not installed at all.

    2.There is no question mark or exclamation mark in front of the "network adapter" in the device manager, after checking that the network card driver is normal, but there is still no local connection icon, if this situation may be caused by the error of the "network connection management service program", we can try the following operations to repair the service program, click the "start" menu - > select "run", enter the three commands in the red part below in order, press enter, and it can be repaired;

    regsvr32

    regsvr32

    regsvr32

    Solution: If you know the motherboard model, you can search for the network card driver of the motherboard of the model, and copy it to the system through a USB flash drive to install it. Tips: According to the model of the network card, the driver should be copied to the system for driver installation according to the network card model.

    The third type: the NIC is disabled, right-click "Network Neighbor" and select "Properties"; In the pop-up "Network Connection", check whether the word "Disable" is displayed on the "Local Connection" icon, if so, it means that the NIC is disabled, right-click "Local Connection" and select "Enable";

  2. Anonymous users2024-02-04

    This is because there is no network card in the computer.

  3. Anonymous users2024-02-03

    Are you promoting your experience?! There is no local connection should be caused by the network card driver is not installed, your situation is that the motherboard has disabled the network card, just turn it on, of course, the factory reset is also on, the factory reset does not need to be discharged, the first motherboard page load....The first item is a factory reset.

  4. Anonymous users2024-02-02

    Now find "Network Adapters" under Device Manager, and find a yellow exclamation mark and a yellow question mark in the network card driver below.

    Right-click on the program with a question mark (exclamation mark) and select "Update Driver Software", as shown in the figure, reinstall the NIC driver step by step, or use the driver wizard to automatically install the driver, after installation, "Local Connection" will appear.

  5. Anonymous users2024-02-01

    Do you have a network card driver? There is no local connection, mainly because the network card driver is not installed or not!

  6. Anonymous users2024-01-31

    Have an online neighbor on your computer monitor? If there is one, click on the online neighbor with the right mouse to click on the blank, in the dot property. There's a broadband connection on it.

  7. Anonymous users2024-01-30

    How to configure the local connection of win7 system without a valid IP address.

  8. Anonymous users2024-01-29

    Start, Run, Device Manager, and see if the network adapter has a yellow one! No.,If there is, your network card driver is not installed.,You have to install it.。 Either your network card is hanged, or you don't have a network card.

Related questions
15 answers2024-02-08

1. The speaker power supply is not plugged in.

2. Inadvertently muted. >>>More

14 answers2024-02-08

What are the specific problems? If you want to reinstall the system by yourself, you can choose the easy-boot USB flash drive startup maker to reinstall the system. The installation steps are as follows: >>>More

8 answers2024-02-08

After unplugging the power supply, there is battery power, and the computer has a high-performance working state to an energy-saving state, at this time, the computer is mainly based on battery life, and no longer blindly pursues high-performance working state, so all the performance has been reduced to reduce energy consumption. This is called slowing down.

8 answers2024-02-08

First of all, you have to modify the registry, and if you don't change the BIOS, it will be a blue screen! >>>More

3 answers2024-02-08

It is a dynamic link library file stored in the C: Windows System32 directory, which provides functions for other programs to call. It can realize the functions of connecting to the Internet, recording input, monitoring applications and so on. >>>More