How FinalData guides data recovery

1.If you don't have important data (value chain or something of special significance, you can try the following methods to not only recover the data, but also learn a lot).

Do not use fdisk mbr to repair it, using this command may cause data loss from your entire hard drive.

Solution: 1. Use Jiangmin antivirus software to repair the hard disk partition table.

2. Restore the backup partition table.

3. Use finaldata to recover data (easyrecovery is not recommended).

Suggested solution: Use finaldata to recover data.

Processing steps: 1. Remove the disk with the partition table damaged, and do not perform any operation.

2. Find another hard disk, set it as the main disk, and install the system, and leave the hard disk with a space of about 1 3 or more than the total capacity of your bad disk (adjust it appropriately according to the total capacity of the files to be recovered).

3. Turn off System Restore for all disks (skip if it's not an installed XP system).

4. **finaldata and installation (there are many on the Internet, a lot of searches), and the installation should allow the management of more than 10M files, otherwise the possibility of your **recovery will be small.

5. Shut down the computer, set the disk with the corrupted partition table to hang on the computer from the disk and restart the system.

6. Use finaldata to perform a logical scan of the disk with the partition table corruption, and you can see the list of lost partitions in about a few minutes.

7. Double-click the corresponding partition to open it, find the file you need, right-click >recover, select the path to the new hard disk, and the file will be recovered and copied.

Note: 1. If the data of the hard drive with partition table corruption is overwritten, then the possibility of repairing the recovered files is less. So don't do anything until you do a recovery.

2. It is best to put the recovered files in the new hard disk, which is not only fast, but also will not overwrite the data of the original hard disk.

3. The system restore must be turned off under the XP system, otherwise it may cause data damage.

4. Be patient, don't be aggressive, sometimes you need to wait slowly.

5. For finaldata, after finding the partition, you can double-click to enter to recover all the existing files of the original partition, no need to use the lost file search function inside, otherwise it will not only waste time, but also retrieve a large number of files that you have deleted in this partition (these are junk data relative to hard disk data).

2.If you have particularly important data, don't explore it yourself, and the most important thing is not to use any read and write operations on the hard drive, as these may lead to data loss, and it is recommended that professionals recover After all, they are experienced and can retain more valuable data from the hard drive.

finaldata

1.After entering the finaldata interface, I found that it is very similar to Windows Explorer, the left part is the directory tree, and the right part is the file window, they.

The way of operation is also not much ......

2.Click on the "File" "Open" command, or click the Open button on the file bar, and select the magnet you want to recover in the "Select Drive" dialog box.

Disc ......After analyzing the drive letter, the sector range of the drive letter will be listed, and here you can estimate the approximate location of the lost files first, and then advance.

Line scan ......4.The next step is to perform a disk scan, and the directory in the middle box is the directory found by finaldata.

5.When the selected entire disk scan is completed, all the files in the disk will be listed on the right side of the action area where the normal files and deleted files folders.

...... is clearly marked

6.Select the files you want to recover, click the "Save" button, the "Save" dialog box appears, and the location of the save is better to choose another drive. Reach.

This, all the lost files are rescued back ......

No more ......worrying about data loss

1. Open the "FinalData Enterprise Edition" window, and then click the "File" "Open" menu command.

2. Open the "Select Drive" dialog box, select the hard drive partition you want to recover data from in the "Logical Drive" tab, and click the "OK" button.

3. finaldata starts to scan the deleted data in the selected hard disk partition, and after the scan is over, the "Select the cluster range to search" dialog box will be opened. Searching for clusters takes a long time, but a full search is still highly recommended. This is because even if the lost data can be displayed even after the search cluster is removed, it cannot be recovered to the maximum extent.

Click the OK button.

4. In the left pane of the finaldata program window, the folder where the files you want to repair are located, then close and right-click the files you want to recover in the right pane, and select the "Recover" command.

5. Open the "Select Folder to Save" dialog box, select any safe location in the car except the partition where the recovered data is located, and click the "Save" button.

6. After the recovery is completed, you can open the selected save folder to view the recovered files.