What is the reason for the difficulty of supporting the pallet on the Ward harvester?

There is straw in the paddy that comes out of the World harvester, which is not clean because the grass is tangled at the upper end of the conveying trough.

There is a lot of straw in the grass, which is mainly caused by the poor matching of the air volume of the fan, the mesh size of the sieve, and the vibration frequency of the sieve, which are all design defects, which cannot be solved even after sale.

You can only try to increase the air volume and change the sieve mesh eye to a small mesh, which will have some improvements. However, if you change it, you may run out of food. Remember to look at the mesh size of the sieve the next time you change the car, the smaller the mesh, the better the design, and the bigger the mesh, the worse the design.

In order to prevent the grain from running, the sieve eye can only be enlarged, and the larger the mesh, the easier it is to enter the straw. In general experience, there is almost no straw in the grain collected by the sieve, and there is straw, and it is very dirty upward.

The top harvester carriage is short-sighted, it may be stuck somewhere, or the position of the bearing or other position, and its speed is not tightly stuck, resulting in a difficult waste board.

In this case, it is his power that is damaged, and in this case, it may also be rust, both of which are relatively common phenomena.

In one is to see if the pressure of the multi-way valve can be reached. The pressure can be increased by adjusting the adjusting bolt under the multi-way valve.

I'm struggling to have a tray on my phone, what's the reason? It wasn't untied too tightly, and he had to be loosened before he could get on.

Summary. Hello dear<>

The answer you are looking for: the World harvester does not unload and unload the first check the following points: whether the World harvester is unloading the items is overweight, if it is overweight, you may need to unload part of it before unloading.

Confirm whether the unloading position is stable, if the ground is uneven, it may affect the unloading effect. Check that the unloading system is working properly and may need to repair or replace parts if it fails. If all of the above is normal, you can try to adjust the unloading angle or unloading position, sometimes fine-tuning can solve the problem of cleaning up foreign objects:

Open the hydraulic oil pipe, clean up the blocked debris, wipe the dust of the equipment, and ensure the normal operation of the hydraulic pipe. Clean the overflow hole: fix the oil cylinder of the harvesting table, separate the oil cylinder and the oil pipe, find the cause of the overflow hole blockage, remove the foreign matter blocked by the overflow hole, and diagnose and eliminate the fault scientifically and reasonably.

If the harvester still cannot operate normally after the above two elimination methods, the screws in the multi-way reversing valve should be adjusted and the multi-way steering valve should be fixed.

The World harvester could not be unloaded.

Hello dear<>

The answer you are looking for: the World harvester does not unload and unload the first check the following points: whether the World harvester is unloading the items is overweight, if it is overweight, you may need to unload part of it before unloading.

Confirm whether the unloading position is stable, if the ground is uneven, it may affect the unloading effect. Check that the unloading system is working properly and may need to repair or replace parts if it fails. If all of the above is normal, you can try to adjust the unloading angle or unloading position, sometimes fine-tuning can solve the problem of cleaning up foreign objects:

Open the hydraulic oil pipe, clean up the blocked debris, wipe the dust of the equipment, and ensure the normal operation of the oil pressure pipe. Clean the overflow hole: fix the oil cylinder of the harvesting table, separate the oil cylinder and the oil pipe, find the cause of the overflow hole blockage, remove the foreign matter blocked by the overflow hole, and diagnose and eliminate the fault scientifically and reasonably.

If the harvester still cannot operate normally after the above two elimination methods, the screws in the multi-Bright's reversing valve should be adjusted to fix the multi-way steering valve.

Hello dear<>

The extension you're looking for: Kiss When a World harvester can't unload the tarbour, there are some checks and adjustments that need to be made to ensure that the unloading goes smoothly. First of all, it is necessary to confirm whether the unloaded items exceed the weight that the harvester can bear, if the mold is too heavy, it may cause the harvester to unload difficult.

HarvesterIt is an integrated machinery for harvesting crops. Harvesting, threshing, and concentrating the grains in the storage silo at one time, and then transporting the grain to the transport vehicle through a conveyor belt, or manual harvesting, laying the straw of rice, wheat and other crops in the field, and then using the grain harvesting machinery to pick up and threshing.