-
1. If the refrigerator was just delivered to your home today, to put it simply, pay attention to the following five points: 1Adjust the two front feet of the refrigerator (the back feet can't be adjusted) to balance the refrigerator, the back is about 10 cm away from the wall, the top is 30 cm, and no debris is placed around; 2.
Clean the electrostatic ash, clean the refrigerated and freezer compartments with a rag; 3.Because the refrigerant material is shaken after handling, it is easy to damage the compressor or reduce the life of the refrigerator when it is immediately energized, so the refrigerator needs to stand still.
After more than 6 hours, turn on the electricity, keep the refrigerator door open and take out the freezer drawer when standing, so that the plastic smell in the refrigerator is emitted; 4.In the future, pay attention to keep the sealing strip clean to avoid corrosion, aging, and air leakage; 5. Do not start the compressor immediately after the refrigerator is stopped, but stop for 2-5 minutes before starting.
2. Precautions for food storage a. Test run the empty box for about 2 hours, and then store the food after the temperature in the box reaches a stable level. b
The food stored in the box should not be too crowded, and there should be a convection gap for cold air to maintain a uniform temperature. c. Hot food should be cooled before it can be put into the box, otherwise it will affect the taste of other foods and increase power consumption. d. Ice cream, fish and other animal fat foods should be stored in the freezer (utensils), not on the door shelves and near the door, because the temperature is high.
e. Liquid beverages such as beer, orange juice, and water cannot be stored in the freezer (container), otherwise they will freeze and burst.
3. After the power is turned on, according to the experts' suggestions, you can use the seven test methods to test the "inside" of the refrigerator.
First, check the door. When the door is closed, it will automatically close due to the suction of the magnetic strip when it is close to the door frame, and there should be no gaps.
Second, inspect the compressor. When the power is turned on, the refrigerator can be started and put into operation immediately; When the power is cut off, the refrigerator shuts down normally; When starting again, the compressor should be up and running normally within a second.
Third, check the "movement". After the compressor starts to start, the refrigerator will tremble slightly, resulting in an operating noise that should not be higher.
45 decibels, i.e. in a quiet environment, only a slight hum of the compressor can be heard, and at a distance of about a meter from the refrigerator, the sound should not be heard. When touching the box with your hand, there should be no obvious vibration.
Wait, you can take a look at the library.
-
Generally, after the refrigerator is bought, first remove all the packaging components, then clean the refrigerator, then let the refrigerator stand for more than 30 minutes, then turn on the power supply, and tear off the plastic film on the refrigerator door and side panel to prevent affecting the normal heat dissipation of the refrigerator, so that it can be used.
-
First of all, put the refrigerator steady, push left and right to see if it is flat, adjust the bottom foot with a foot, and find a hard object to pad it if not. Let it sit for a while, at least an hour. Pre-cool the food for a period of time before using it.
-
Put it on for more than two hours, because it is often handled, the refrigerant flows, 2, wipe it in the refrigerator with vinegar to eliminate the odor, 3 first use the plate to decorate the water and freeze it, and see the effect! 4. Check whether there is abnormal noise, fever, etc.! Together it works, congratulations on you can use it!
-
It should be left for a while, then the empty cabinet will be run for a while, and if it is okay, you can put things away.
-
If you buy a new refrigerator, you should wait 2 hours before turning on the electricity, and you should use a clean soft towel and wash it with warm water.
-
I think I heard that it can only be used after a while.
-
Before putting food, it is necessary to wipe off the inner tank and pay attention to hygiene.
-
The same is true for freezers.
-
There will be points to be noted in the manual.
-
Look for the manual, it should be very detailed.
-
Introduction: When you buy a new refrigerator and go home, many consumers don't know what they need to pay attention to, so they use it directly. In fact, there are many problems that need to be paid attention to in the process of using the refrigerator, which involves a lot of maintenance problems.
Clause. 1. Refrigerators and other electrical appliances cannot share an outlet.
The current of the refrigerator when it is started is very large, which is 5-10 times that of normal operation, and the color TV is 7-10 times that of normal use. If the refrigerator and color TV are started at the same time, the socket and wires will be difficult to bear, and there will inevitably be a risk of short circuit. At the same time, when the refrigerator is started and running, electromagnetic waves are generated, which affects other electrical appliances, so the refrigerator and other electrical appliances cannot share the same socket.
Clause. 2. Three-phase sockets must be used.
From the safety point of view of the refrigerator, the refrigerator must have reliable grounding, that is, it must use a three-prong socket, and it is truly grounded, even if a three-prong socket is used, if there are only two wires connected inside, there is no grounding.
Clause. 3. Do not stop using the refrigerator for more than 3 months.
In general, the refrigerator should not be deactivated. The increase in temperature when not in use will accelerate the corrosion of the pipes and affect the life of the refrigerator. If the refrigerator is out of use, wipe the refrigerator inside and out, then open the door and place it, cover it with a breathable cloth or put it in a clean place, be careful not to seal it, the seal will produce odors.
It is normal for the refrigerator to emit a certain odor when it is used again, once the power is turned on for a period of time, the odor will disappear automatically, and the downtime should not exceed 3 months.
Clause. 4. The refrigerator should be placed in a cool and ventilated place, avoid direct sunlight, and stay away from heat sources, because the high ambient temperature around the refrigerator will increase the power consumption of the refrigerator.
Clause. 5. The refrigerator that cannot be automatically defrosted should be manually defrosted in time when the frost thickness on the evaporator exceeds 4 5 mm.
Clause. 6. Keep the door seal clean to ensure its suction.
-
Before using a new refrigerator for the first time, you need to pay attention to the following points:
1.Cleaning the inside: Before use, you need to open the refrigerator to check if the inside is clean, if there is dust, you need to wipe it with clean water and mild detergent, and wait until it is all dry before use.
2.Wait 4 hours: In a newly purchased refrigerator, the compressor and refrigerant need to adapt to the new environment during transportation, and need to be left for more than 4 hours before using the refrigerator before starting to use.
3.Set the temperature before putting food: When you start using the refrigerator, you need to cold the condenser and bring it to the right temperature before putting the food in.
4.Avoid overload: Before the operation of the new Yu grip refrigerator, it is recommended to understand its refrigeration and freezing capacity to avoid food piling up together and overloading, which will affect the refrigeration effect.
Ways to get rid of the smell of the refrigerator:
1.White vinegar: Placing some open white vinegar in the refrigerator can absorb odors and remove odors.
2.Flour: Place some open flour in the refrigerator to absorb odors from the inside of the refrigerator.
3.Carbon volic acid drinks: Wiping the inside surface of the refrigerator with carbonated drinks can remove odors.
How to maintain the refrigerator:
1.Regular cleaning: Clean the refrigerator every once in a while, especially the rubber sealing strip on the refrigerator door.
2.Separate food storage, avoid mixing different foods, and pay attention to moisture and odor removal.
3.Avoid over-stocking food: Leaving too much food in the refrigerator and freezer can cause the compressor to run more often and increase energy consumption.
4.Defrost at regular intervals: Regular frosting allows for better maintenance of the refrigerator and reduces the amount of electricity consumed when the refrigerator compressor is working.
5.Replace the activated carbon filter regularly: For refrigerators that can hold activated carbon filters, regular replacement is also one of the more important steps.
-
1. Without plugging in the power supply, open all the doors, take out each drawer, expose it to the air for a period of time, and remove the odor in the refrigerator;
2. Use a clean wet towel to scrub the inner surface of the refrigerator box and the surface of each drawer to remove unhygienic impurities on the surface;
3. Make the back and both sides of the refrigerator away from the wall and cabinet surface at a certain distance (generally 15 25 cm is appropriate), and place it in a well-ventilated position as much as possible;
4. The filter plug of the drain nozzle below the back of the refrigerator should be put up;
5. Try to find a place where the indoor temperature is high and plug in and start using it.
You can also buy some charcoal packets to remove odors and keep them in the refrigerator for a while).
-
Common sense of refrigerator use:
1. After the new refrigerator is purchased, it should be wiped several times with a clean rag, but do not close the door after wiping it clean, open the door to let the odor inside dissipate and then use the electricity, or use an electric fan to blow it inside to speed up the emission of the odor.
2. After the new refrigerator is carried back, it should be left for about 2 hours before powering on the test machine.
3. The refrigerator should be placed in a cool and ventilated position, and a certain amount of space should be left around it to facilitate the ventilation and heat dissipation of the refrigerator and improve its refrigeration efficiency.
4. Before powering on the test, you should read the manual in detail and set the temperature according to the operation method on the manual. The temperature of the freezer should be adjusted to minus 18 degrees Celsius, the refrigerator should be about 5 degrees Celsius, and the temperature of the variable temperature room in the middle should be adjusted reasonably according to the type of food to be stored and the length of storage time. If there is no food in the freezer that needs to be stored for a long time, the temperature can be appropriately adjusted to about minus 12 degrees to minus 16 degrees, which will save more electricity, especially in summer.
The same goes for the refrigerator, which can also be raised to between 8-15 degrees if there are no special food requirements to preserve, which is also more energy-efficient. The mechanical thermostat should adjust the size of the digital gear according to the ambient temperature of the season, adjust the smaller digital gear in summer, adjust the middle gear in spring and autumn, and adjust it in the larger digital gear in winter. In summer, it is the most power-efficient to adjust to 1st gear.
5. When the machine is powered on, do not put in the food first, wait for the temperature in the refrigerator to drop and stabilize, and then slowly put in the food after the compressor starts and stops normally, and do not put too much food at one time to avoid overload of the compressor.
6. The food placed in the refrigerator should be sealed and wrapped in a container or food bag to avoid odor caused by mutual odor.
-
1First of all, read the attached product manual carefully and check the various parts of the refrigerator.
2. Check the power supply of the family, whether it is grounded, and whether it is a special line.
3. Can you hear the working sound of the compressor after powering on?
4. When starting to use, it is necessary to run with load reduction, because the moving parts of the new machine have a running-in process. After running for a period of time, add a large amount to prolong the life of the refrigerator.
Be careful not to place it in a place where there is a heat source.
-
For refrigerators that are first plugged in, the start-up time is relatively longIt takes about 5 to 6 hours before the downtime is possibleThis is because the refrigerator needs enough cooling capacity to go from room temperature to minus 18 degrees.
Under normal circumstances, the refrigerator is basically stable after 24 hours of continuous operation, and the start-stop ratio tends to be normal.
The newly purchased refrigerator should be left for 3 hours before it can be plugged in
Because the compressor of the refrigerator refrigeration system needs to be protected by lubricants when it is running, under normal circumstances, the manufacturer will put a certain amount of lubricating oil in the refrigeration system and seal it inside. During the refrigerator transport, the resulting bumps cause the lubricating oil to flow into the coils of the heat exchanger.
When there is a severe bump, it tilts and the oil can flow into the cylinders of the compressor. Immediately after delivery, the lubricating oil in the pipes will block the flow of refrigerant and will also affect the normal operation of the compressor. The serious consequences are that the lubricating oil hits the cylinder and paralyzes the operation of the refrigerator.
-
1. Adjust the two front feet of the refrigerator (the back feet cannot be adjusted) to make the refrigerator balanced, and you can use bottled water to leave a bubble to test;
2. Clean the electrostatic ash and clean the refrigerated and freezer compartments with rags;
3. Because the refrigerant substance is shaken after handling, it is easy to damage the compressor or reduce the life of the refrigerator after being powered on immediately after being powered on for more than 6 hours, and the refrigerator door is always open and the freezer drawer is taken out when standing, so that the plastic smell in the refrigerator is emitted;
4. Pay attention to keep the sealing strip clean in future use to avoid corrosion, aging, and air leakage;
-
Precautions when using a new refrigerator for the first time:
Please read the manual carefully before use, and then turn on the power.
The running time should not be too long when used for the first time, and it should be carried out intermittently to give each part of the refrigerator a running-in process. It is then operated on a small setting or slightly higher set temperature.
When the new refrigerator starts working, it should be opened empty and stopped before putting food in. The amount of food stored should not be excessive, and the amount of food stored should be gradually increased as the working hours of the refrigerator increase.
Precautions for using the refrigerator:
When the refrigerator is working, minimize the number of times it is opened and the air conditioner overflows.
The power supply voltage fluctuates greatly. In case of repeated power outages, the refrigerator should be suspended and the power plug should be unplugged to prevent the compressor from burning out. After the refrigerator stops, do not immediately turn on the power to start the compressor, but stop for 2-5 minutes before starting.
In the event of a temporary power outage, unplug the refrigerator first; Minimize the number of unboxing doors in the event of a power outage, and keep food fresh for 15-20 hours when the refrigerator door is closed.
During the use of the refrigerator, we should pay attention to its refrigeration performance and choose the most suitable refrigerator temperature for our home. Changing the temperature controller knob can change the temperature inside the refrigerator.
In the early stage, it is necessary to study the population of the community, how many, what kind of people, the main demand is in, what kind of business is around, there is no shortage of convenient retail such as small supermarkets, and there is the location selection, which should be selected on the road with convenient population flow. There is also the grade of the purchase, the variety or something. >>>More
Feeding of pheasants.
Feeding: After two months, no feed should be fed, and only corn, wheat, barley and other miscellaneous grains should be fed. The pheasant raised in this way has a thin layer of fat under the skin, and it is very fragrant when it is stewed with butter bleached on top. >>>More
To use waterproof, because of the sweat, and then SPF is high, at least 30 or more, in fact, that thing is useless, I also use it during military training, but just like my aunt said sunscreen is sunburn, after applying it is to prevent you from sunburning, but in that kind of exposure, it is useless for people with active melanin to apply more, I am like that, and the bedroom next door to me, **is good no, but you can choose a good after-sun repair, do it every day after military training**, If you have an economic foundation, you can use Sekkisei to compress your face, which is well-known, and you can check it on the Internet.
The preparation for repeating is as follows:1. Mental preparation. First of all, strengthen your confidence, since you have decided to repeat the study, you must be determined, indomitable, not looking ahead, hesitating, and wavering from time to time. >>>More
Perm is generally to use a reducing chemical solution to disassemble the cystine spring first, so that the cystine is thinned. The sulfur bridge bond breaks off and becomes two cysteines. At this time, the amino acid links of the hair loosen and coil into a certain waveform at the mercy of others. >>>More