Windows7 disk can t be opened, how to solve it

It's written and protected.,The next cracked software.,Just crack it.。

Buying a new machine solves the problem

If this page appears, it may be that the software has a virus or the file has been damaged, so it is caused by the prompt blocking of the security software. If you feel that this software is safe, you can choose to "dismiss" and add it to the trust. If you don't feel safe, you can select "Clear now and scan fully".

Fault phenomenon

When double-clicking or right-clicking to open a disk on a computer, an error message "Inaccessible" appears.

Cause analysis. Sudden power failure or forced removal of the hard disk during use may cause damage to the disk and the location is unavailable.

The partition table is corrupted, resulting in incorrect reading of partition information and the failure to read the file system.

The data cable or power cable of the hard disk is not in contact with each other, resulting in incomplete reading of the information on the disk.

If the hard disk has bad sectors, when the location of the bad sectors is at the key position of the file system, the entire partition file system will not be able to read normally.

The user privilege is too low to access the disk.

Resolution. If there are no important files in this disk, you can format the disk directly.

If the file is not too important, it is best to keep it, you can use the command to repair it directly (the feature is fast, but there is a risk of repair failure) to operate the desktop in the lower left corner of the "start"-run-cmd type chkdsk h: f (h disk that needs to be repaired), and wait for the repair to be completed.

The above content reference: Encyclopedia - Inaccessible

1. Open the start menu, click Run, and enter enter enter in the run window to open the Group Policyr;

2. Open User Configuration - Management Module - Windows Components - Windows Explorer, and double-click on the right side to open "Prevent access to the drive from 'My Computer'";

3. Check "Not configured" or "Disabled" in the pop-up window, and then click OK.

1. First of all, we need to press Win r to open the run window and enter gpedit msc

2. Then we need to open it in the window, open it: User Configuration Management Template Windows Components Windows Explorer, find and open the right side to prevent access to the drive from my computer.

3. Finally, we need to select in the interface"Enabled", and then click"OK"

1. First of all, we need to press win+r to open the running window and enter.

2. Then we need to open in the window, in turn: User Configuration Management Templates Windows Components Windows Explorer, find and turn on on the right to prevent access to the drive from "My Computer".

3. Finally, we need to select Enabled in the interface, and then click OK.

1. Use the shortcut key "win+r" to open the running window, and enter;

2. In the window, open it in turn: "User Configuration", "Management Template", "Windows Components", "Windows Explorer", find and double-click in the list on the right to open "Prevent access to the drive from 'My Computer'";

3. In the interface that opens, select "Enabled" and click "OK".

What should I do if the win7 system can't open the local disk?

The specific solution is as follows:

1. Use the shortcut key "win+r" to open the running window, and enter;

2. In the window, open it in turn: "User Configuration", "Management Template", "Windows Components", "Windows Explorer", find and double-click in the list on the right to open "Prevent access to the drive from 'My Computer'";

3. In the interface that opens, select "Enabled" and click "OK".

If you are still confused about the problem that the win7 ultimate system can't open the local disk,Take the above three steps directly to set up the tutorial,Can't open the disk,You can't view the files inside,Affect work and learning,I hope the content of this tutorial can help you!

Many friends found that after installing windows7, there was an inexplicable problem: after the disc was put into the optical drive, the name and capacity information of the disc could be displayed, but no matter whether it was double-clicked or right-clicked in the menu to open, there was no response!

Attached below is the workaround:

1. Win key + R key to open the running window, enter "regedit" and press enter to open the registry;

2. The following locations:

hkey_current_user\software\microsoft\windows\currentversion\explorer\cd burning\staginginfo\volume

Note that the curly braces above are random numbers, which may not be the same for different machines, then right-click on the key value of StagingPath in the right box and enter an arbitrary valid path (the default is C: Users (your username) AppData Local Microsoft Windows Burn Burn).

Ok, now close the registry and open the "computer" or explorer in windows 7, is the problem solved?

This method does not require you to boot up your computer.

Try it on another computer and see if it's a disc problem.