How do I use two wireless routers on one switch?

The switch is connected to the router, and there are two ways to set it up (multiple routers are set up like this):

The first method: dynamic IP mode.

1. Plug in the router, don't connect the switch first, reset the router (restore the factory);

2. Connect the computer to any LAN port of the router and enter the setting page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the switch to the WAN port of the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router and change the IP address of the router. For example, most router addresses are, we just need to change the router IP address;

2. Turn off the DHCP function of the router in the settings;

3. Finally, connect the network cable from the switch to the LAN port of the router (any one is fine), note that it cannot be the WAN port.

First of all, if the network segment of your first route is connected to the WAN port of the wireless route from the LAN port of the first router, then the IP should be set to the same network segment as the first router, that is, the WAN port connection mode of the wireless router is set to static IP connection, and the IP is the same network segment as the first route, and then the LAN port IP of the wireless route should be set to a different network segment or other OK, as long as it is not duplicated with the first route network segment. The network segment of the machine under the wireless router should be set to the same network segment as the LAN port of the wireless router or enable the DHCP function on the wireless router, automatically assign IP, and then turn on the wireless function, set a password, this should be able to search the wireless network, and then connect to the wireless network, and you should be able to access the Internet.

Absolutely, as long as the two routers are no longer the same gateway.

Steps:

1.Set your wireless router first, change the address of the LAN port, that is, the gateway address, to a different address from the main router upstairs, for example, the gateway upstairs is your wireless router, change it to something like that, and don't worry about the rest of the settings.

2.Then it is to directly connect the cable that you go upstairs with the external network to the LAN port, remember that the LAN port is not the WAN port, and use it as a wireless switch. The premise of this statement is that you have at least two IPs (i.e., IPs) assigned to you by the network management system

Connect your wireless router to the local machine, and change the LAN IP of the router, which is the LAN IP. You can change any IP segment at will. Like what. Try to change it to a rare one to avoid conflicts with existing routes or computer IPs in the local network.

At this point, you can connect to your wireless and go online.

1. It's best to add a password so that others don't use it.

2. The IP of the wireless network card of the computer is set to the same IP segment as the previous network card, if it was not set before, then there is no need to set it.

The steps to connect the router to the two switches are as follows:

1.Start by opening the router and dragging out the router and the two switches and the two computers and branches, and arrange them in order.

2.Then the name of each network device is weighed.

3.Start by connecting a router and two switches, then connect them using a crossover cable.

4.Double-click to enter router R1 and open the F0 and F1 ports.

5. At this time, the switch S1 and PC1 are connected, and the cross wire is also used.

6. In the figure, the switch S2 is connected with PC2, and it is also connected with a cross let sensitive wire.

7.The connection is complete.

Of course, you can, as long as the router is set up correctly, there is no problem connecting to the switch.

1. The bus of the broadband network is connected to the WAN port of the router, and the LAN port of the router is connected to the computer.

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.