How do I get an error F1 when I get an ASUS Z490 Bois close?

Please enter setup to recover BIOS setting when booting up, press F1 to run setup

This prompt is to reset the BIOS, or to reset certain options.

The main reason is that after entering the BIOS, the time of the BIOS becomes the current time of the non-synchronization, for example, it is displayed on January 1 of a certain year.

At this time, the idea of investigation is:

1) Change it to the current time, save and exit to check if there is still an error, or check whether there is an error message during the interval time.

2) If the time has been changed and the BIOS time cannot be saved, then flash the motherboard BIOS and replace the CMOS battery on the motherboard that stores the BIOS information.

3) The above settings have been set, and the error message will appear, please set the correct boot and boot the device under BIOS - [BOOT] - BOOT1], and then save and exit the BIOS.

There is a prompt to press F1 when you boot up, there are many reasons, how can you solve the problem without a reason.

For example, if the CPU fan is abnormal, the BIOS settings are missing, and the hard disk cannot pass the self-test, etc., it may cause the prompt to press F1 when the computer is turned on.

Therefore, the cause of the fault must be determined according to the specific on-screen prompts, and the corresponding treatment methods can be taken to solve the problem.

It is recommended to send a picture of the specific display on the screen for analysis.

ASUS motherboard boot prompts that you need to press the F1 key, which can be solved in the following ways:

1. After booting up, click the F2 button or DEL button to enter the BIOS interface;

2. Click the F7 key to enter the advanced mode;

3. In advanced mode, find the "Startup" item and turn off the "If there is an error, wait to press the F1 key" setting.

Through the above steps, you can close the interface of the startup prompt F1.

Usually this situation is caused by the CMOS date and time error, and under normal circumstances, press F1 to enter the setup.

Set the correct date and time, then press F10 to save and exit and restart the computer to solve the problem.

If the fault persists after the date and time are set, then it is possible that the motherboard's coin cell battery is dead.

After replacing a battery, you can reset the date and time.

ASUS motherboard boot prompts that you need to press the F1 key, which can be solved in the following ways:

1. After booting up, click the DEL button to enter the BIOS interface;

2. In the boot item, set wait for f1 if error to disabled.

Through the above steps, you can close the interface of the startup prompt F1.

1.The battery is out of power, it is recommended to replace the battery; 2.Go to the BIOS, see the floppy drive, and then tap Settings to turn it off.

It is set to none.

Go to the BIOS

Go to the main menu and see Legacy Diskette a [ In [ Enter, set none or disabled.

Different motherboards have different settings, and the basic menu is pretty much the same.

Boot into the item should be boot is not out of the F1 key. Just close it here.

If there is no such setting in the BIOS, it does not support the function of turning off the motherboard self-test failure and the F1 button is not out.

You need to press the F1 key to enter the boot, mainly because the settings in the BIOS do not match the real hardware data, which can be divided into the following situations:

1. In fact, there is no floppy drive or the floppy drive is broken, but there is a floppy drive in the BIOS, which leads to pressing F1 to continue.

2. I originally hung two hard disks, and set them as dual hard disks in the BIOS, but later forgot to change the BIOS settings back when I removed one of them, which will also cause this problem.

3. If the motherboard battery is out of power, it will also cause data loss, which will cause this failure.

4. Reboot the system, enter the BIOS settings, and find that the floppy drive is set to, but in fact there is no floppy drive in the chassis, set this item to none, troubleshooting.

ASUS motherboard boot prompts that you need to press the F1 key, which can be solved in the following ways:

1. After booting up, click the F2 button or DEL button to enter the BIOS interface;

2. Click the F7 key to enter the advanced mode;

3. In advanced mode, find the "Startup" item and turn off the "If there is an error, wait to press the F1 key" setting.

Through the above steps, you can close the interface of the startup prompt F1.

Boot requires pressing F1 to enter the system troubleshooting.

Under normal circumstances, the requirement to press F1 to enter the system is caused by a minor problem with the system's BIOS settings that do not affect the system startup, so please check the hardware information settings in the BIOS for discrepancies with the actual situation.

The common faults in general are:

1. The battery on the motherboard is dead.

Solution: Replace the motherboard battery.

2. You have set up the floppy drive to start, but there is a problem with your floppy drive.

Solution: A. Press del to enter the BIOS at boot, boot up the boot sequence, and turn off the floppy drive to boot.

b. Turn off the detection function of the floppy drive when it is turned on

Start the computer and press the [DEL] button to enter the main BIOS settings interface.

Select the "Advanced BIOS Features" setting item and press the Enter key to enter;

Set "Boot Up Floppy Seek" to "disabled" to turn off boot software detection.

Because the motherboard is different, the content in the BIOS is also different, so there are some things that you can't find.

Press delete to enter BIOS when booting,Generally in the second item or there is a boot option,After entering, there will generally be a line with first,The next line has the second word,And then there is a third,It represents the boot order,These three lines are optional,You choose something else in the selection behind the first,For example, HDD,It is on behalf of the hard disk cdrom stands for optical drive,Anyway, don't choose floppy,It represents the floppy drive,Then save,Exit on the line。

Does it mean press f1 to continue, del to enter setup ?

After booting up, press Del to enter the BIOS, select None in the floppy drive and press F10 to save.

This failure occurs due to data loss due to a dead motherboard battery. In this case, the system time is displayed incorrectly.

It is recommended to adjust the CMOS battery first to avoid poor battery contact.

If the adjustment is invalid, it is recommended to replace the CMOS battery, and the battery specification is CR-2032

The BIOS time is wrong, is it because the motherboard battery is dead, and the BIOS settings cannot be saved?

Popularize computer repair and application knowledge.

Answer 1: After the computer is turned on, press the "DEL" button repeatedly to enter the BIOS settings of the motherboard, and press the F7 button to enter the "Advnced Mode".

2. We find the boot tab (boot) and enter the boot settings option, as shown in the figure below.

3. Find "If there is an error, wait to press the F1 key" and select the drop-down, we modify it to "disabled" to close the state.

4. After confirming that the modification is "disabled" and closing the state, we can press the F10 key to save and exit the BIOS.

Question: The setting on the BIOS has no effect.

The question has been confirmed by pressing f10 and the closure has not been successful Persists.

Question: My motherboard doesn't have a coin cell battery.

Question: I seem to be an ASUS M88 series motherboard.

There is no way to discharge depressed.

ASUS motherboard boot prompts that you need to press the F1 key, which can be solved in the following ways:

1. After booting up, click the DEL button to enter the BIOS interface;

2. In the boot item, set wait for f1 if error to disabled.

Through the above steps, you can close the interface of the startup prompt F1.

You can turn it off directly under the BIOS.

Methods and Steps:

1. Press "DEL" immediately to enter the BIOS interface.

2. Enter the advanced mode, open the "Boot" tab, and click "Wait For.""f1"if error" will pop up the dialog box.

3. Select disabled and press Enter. Then F10 + Enter, save and exit.

Popularize computer repair and application knowledge.