There is often moisture in the dial of Inag watches, so please ask if you want to clean it

Yes, if the water is gas, it is best to find the master to open it and clean it and oil it. Otherwise, rust will affect accuracy and service life. By the way, let the maintenance master solve the problem of water ingress.

The sealing performance of the explanation table is not good, send it for maintenance, clean it with oil as a whole, and replace the sealing ring.

1. Put the silicone and the watch in a sealed box first, and take out the watch after a while to see if there is any fog that has been cleared.

2. If there is no silicone at home, or if the fog is not completely removed with silicone, try wearing the watch backwards.

3. Find a household light bulb with a relatively large wattage to bake hot, and wrap the watch tightly with several layers of clean soft wiping cloth or facial tissue before baking to prevent damage and deformation to the watch, and do not bake directly with an open flame.

4. If it still doesn't work, you can only go to a professional maintenance service center to wash the oil and maintain it to prevent rust on the movement.

Hello, yes, I want to solve it, otherwise it will not be good if the movement rusts after a long time.

If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

The seal is not good, it's time to fix it.

There is a ** time after the watch enters the water, and it is best to take it to the repair center to clean up the water within 72 hours.

If the watch is flooded or foggy in the watch, the parts will be damp, and the parts will be repaired before they are wet, and the words and hands will not blister because they are not treated in time.

The reason why the watch will enter the water is because the waterproof measures have failed, it may be the head, it may be the deformation and displacement of the rubber ring of the bottom cover or the face cover, etc., and the specific needs to be tested to judge, if the waterproof measures are not done well, it may cause the watch to enter the water again.

The correct way is to send it for repair immediately to avoid causing more damage.

If you don't repair it in time, then the water will rust the steel parts in the watch movement, and the tiny clock parts usually need to be replaced once they rust, so you should know that the damage to the watch from water is "catastrophic". In addition to movement parts, long-term exposure to moisture can also cause discoloration, blistering and rust on the dial and hands of the watch.

Isn't there supposed to be a warranty, you can ask the customer service.

Water ingress into the watch can be solved by the following measures:

Law. 1. Place the vent - dry the watch with a dry paper towel and then place it in a cool and dry vent for a few hours, and do not place the watch directly in the sun or dry, which is to prevent water mist from flowing into the movement.

Law. 2. Silicone drying - for the water inlet of the mechanical watch, you can use the granular substance of silica gel to absorb water, put the two in a closed container, and take it out after a few hours, and the water mist inside will be cleaned up; If it is a quartz point clock, you can take a few small pieces of calcium chloride, wrap them in gauze, and then open the electronic watch cover and seal it.

Law. 3. Wipe oil and remove rust - method 1 and method 2 can only clear a slight water mist, and for some more serious water ingress, these two work earlier, which is not enough for the rescue time of the movement, at this time it is best to find a professional watch repair center for ** maintenance, oil wiping treatment.

It is recommended that you send it to a professional large-scale clock point for inspection and maintenance. Or it is recommended that you can open the warranty copy attached to the purchase table, under normal circumstances, the warranty copy will have a service address**What can be called**consultation under the nearest maintenance point to you**.

After the warranty period, it will be sent to a professional repair center for comprehensive maintenance and repair as soon as possible. Don't listen to online home remedies, your watch must be fully serviced if it is wet. Hopefully adopt!

How to deal with water ingress into the watch:

If you accidentally get water inside your case, you can use a granular substance called silicone to put it in a meter-closed container with the watch that has accumulated water, and after a few hours, you can remove your watch and the water will disappear. This method is simple, convenient and economical, and does not compromise the accuracy or longevity of the watch. In addition, the silica gel that has absorbed water many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Second, the secret of refurbishment of the watch with water ingress. If your watch is scratched with a lot of lines, you can drop one or two drops of water on the watch mask, and then squeeze a little toothpaste to wipe it, you can remove the scratches and make the watch mask as new.

Third, the maintenance secrets of the watch when water enters. When wearing a watch, the sweat on the hands is corrosive to the case, the all-steel case is nickel-chromium alloy, the corrosion resistance is better, and the semi-steel case is copper, which is in contact with sweat for a long time and is easy to corrode, so you should often wipe off the sweat with a soft cloth or put on a plastic watch holder to prevent it from being eroded by sweat. Do not open the back cover of the watch at will, so as not to let dust enter the movement and affect the normal operation of the watch, thereby shortening the life of the watch.

Do not leave the watch in a closet with mothballs to avoid deterioration of the watch oil. Do not place the watch on the radio, TV to avoid magnetization. Watches that are not worn for a long time should be wound regularly once a month so that the parts will not be in a stationary state for a long time, so as to ensure the operation performance of the watch machine.