Ask the computer whiz, my computer is weird 20

Press F1 should mean that there is a problem with the CMOS setting, press the del key to enter the CMOS setting, and restore the factory settings to see. As for the problem in the system, it must be a Trojan horse, so there are three choices: one is to start over, the second is to kill the virus under DOS Linux, and the third is to use software such as icesword in win to kill the Trojan horse and then kill the virus.

good luck!

Your machine is probably more than just a Trojan.

Is your Kaba upgraded all the time?

Personally, I feel that the virus corrupts the system files causing the problem.

It is recommended to use the upstairs method.

Enter F8 without network security.

If the caba on your machine is also not used properly in safe mode.

Then it is recommended to reinstall Kaba Antivirus again.

If the response is still sluggish.

Then the individual concludes that your system has been badly infected.

It is recommended to reinstall the operating system.

Format all drive letters Save important files.

After reinstalling, install the appropriate drivers and anti-virus software, and it is strongly recommended to back up the system.

At least next time something goes wrong, don't have to be so troublesome to reinstall.

It is recommended to use the Tomato Garden SP2 version, remember that it is best to have a tool phase, and it comes with a backup function in the disk.

Press F1 to start because the CMOS battery on the motherboard is dead, change the battery, it's very cheap, only a few dollars, the problem of Kaba antivirus, you can turn on and hold F8, choose to enter safe mode, and then scan, just kill the virus and Trojan horse.

It's a pigeon virus, it's a remote-controlled virus, The virus does not kill, Kaba can't be scanned, I'm a hacker, it is recommended that if you have**as soon as possible**close, so as not to be monitored by others, if you are often stuck, it is recommended to do a change of speed system, in the future** things pay attention to, etc., install a genuine anti-virus software, so as not to have loopholes and other phenomena.

Oddly enough, I suggest that you press F8 to select Safe Mode when you reboot, and in this mode you will scan your hard drive with Kaba.

Did you format the C drive before reinstalling the system? It may be that the previous information is still causing chaos in the system. Create and reinstall again, format the C drive before installation. If the problem is not solved, then it can be a hardware problem, establish a memory and try it.

The phrase adisk read error occurred literally: a disk read error occurred. From the prompt, it can be seen that there is a problem with the disk.

Is it a problem with the disk cable?Or is the disk itself broken or bad sectors?Or is it a virus?

We need to investigate this series of problems one by one.

First disassemble the chassis, brush off the dust, and replug the disk cable. If it's still the same, use the disk repair tool software to fix it. There are many disk repair tools, such as hard disk repair tool DiskGenius, disk repair tool chkdsk, etc., which can be used, mainly to detect whether the disk has bad sectors, and try to repair it if there is.

This is a very long and long process, if there are important files in the C drive system, use DiskGenius to detect the disk, if it is repaired, everyone is happy, after all, there is no need to reinstall the system. If there are no other files that need to be retained on the C drive, reinstalling the system will definitely be a priority. Due to the limited working time, there are many important things to do, and there is no time to check the disk, so just skip this step and reinstall the system.

When the system is reinstalled, the problem comes again, and the C disk can not be read, so there is only the use of PE system tools, and many friends do not understand that the PE system can be queried directly. If you don't have a PE system disc, you can make one with a USB flash drive, and here I won't talk about how to make a PE system, and the production method is a lot of searches!Use the PE system disk to enter the system, right-click on the C drive, select Properties, open the C drive properties, and find that the disk capacity of the C drive is 0!

This is the essence of the problem of this machine, and the problem of why the system can't be started is also here. If you don't want to format the disk, try to recover the C drive with the disk recovery tool.

Format the C-drive installation system.

Right-click on the C drive, select "Format", select the file system as "NTFS" format, and select "Quick Format" to format the disk C!