How about Haier washing machine XQG90 B1286GU1 detergent?

1. First of all, check whether the filter screen of the water inlet is blocked by impurities, if the water inlet is weak, the laundry detergent may not flow down. It doesn't matter, there is a rubber tube connection between the washing box and the bucket, only the softener compartment can be temporarily stored, because the fabric softener will only be washed down when the last rinse is performed, and the other two compartments will flow directly if the liquid detergent is put in.

2. If the filter is clean, see if the water pressure is enough. If it is sufficient, measure whether the resistance value of the inlet valve is normal (and whether there is a 220V voltage at both ends. The laundry detergent package is generally marked according to the amount of clothing, and the laundry detergent should not be put too much, if the washing machine has an additional rinse function, you can rinse it again.

If you are still afraid of residue, you can also rinse it separately a few more times.

3. If the above tests are normal, it is recommended to dredge the laundry detergent sink, which may be clogged in the detergent trough. Before entering the water, it is good to pour the laundry detergent into the tank, and it will generally be washed into the cylinder by the water when the water is in. If the washing machine is Haier's, there will generally be four slots for detergent, namely:

3. The 3rd and 4th slots are softeners A and C, respectively, where liquid washing liquids such as fabric softeners or spices are placed. If the washing machine is another brand, you can check the manual, or find the washing machine's local after-sales service ** number, and then consult it.

4. This can be placed directly in the drum and then close the door to start the washing program. However, it should be noted that if the laundry detergent has a bleaching effect, it is best to put the laundry detergent first, turn on the machine and let the water and laundry detergent stir evenly, pause for a while, and then put in the clothes that need to be washed, so as to avoid the local contact of the clothes being bleached, causing stains. Alternatively, it can be added directly from the mouth of the detergent.

After adding, do not close the laundry detergent box, you can rinse it with water several times by yourself, so as not to leave the laundry detergent on the wall, and then flush it into the clothes in the next rinse stage, so that there will be secondary pollution.

I can't understand your question, I feel like you may be asking why the detergent can't flow, this should be an impurity blocked in the water inlet filter, you can call Haier customer service and ask them to send someone to help you check what is going on.

Summary. Pro: How to use.

1. First of all, before using the washing machine, check whether there are hairpins, coins or paper towels and other items in the clothes to be cleaned, and if so, take them out.

2. Turn on the power of the washing machine, turn on the faucet, put the drain pipe in a suitable place, put the clothes into the washing machine, and then add an appropriate amount of washing powder, laundry detergent or other cleaning utensils to the laundry detergent box in the washing machine, or pour it directly.

How to use Haier washing machine ultra-clean XQB80 Z118.

How to use 1, first of all, before using the washing machine in the bridge hall, check in advance whether there are hairpins, coins or paper towels and other items in the clothes to be cleaned, and if there are any, take them out carefully. 2. Turn on the power of the washing machine, turn on the faucet, put the drain pipe in a suitable place, put the clothes into the washing machine, and then add an appropriate amount of washing powder, laundry detergent or other cleaning equipment to the laundry detergent box in the washing machine, or pour it directly.

3. Press the power switch of the washing machine, choose the appropriate washing method according to the weight and material of the clothes, such as quick bending drying, gentle and standard, etc., and choose the appropriate water level according to the number of clothes. After the selection is completed, press the start button, and the washing machine can start working when it is bored, and a sound will be issued as a prompt when the washing machine is finished. In the case of dehydration of the washing machine, do not easily open the lid of the washing machine, otherwise it is more likely to malfunction.

When the washing machine is finished, remember to turn off the power and put the drain back in its original place.

The tools that need to be prepared are as follows: washing machine, socket.

1. First of all, ensure that the various connecting wires of Haier automatic washing machine XQG60 B1287 are normal and can be used, Haier automatic washing machine XQG60 B1287 must first ensure that the power is on, you can press the power button of Haier automatic washing machine XQG60 B1287 to try it, "drop" sounds, and it is lit, it means that it is energized.

2. Press the "Power" button to keep the Haier automatic washing machine XQG60 B1287 in a state of preparation, and it should be noted here that there should be no water on the surface of the washing machine, otherwise it will damage the electronic circuits inside.

3. Find the "program" column, because different washing machines, the program is in different positions, but the handwriting reminder is the same.

4. In the program column, find "dehydration", and then press the program button, when the "dehydration" lights up, it's OK, don't press the program button.

5. Press the start to pause the button, at this time, the Haier automatic washing machine XQG60 B1287 did not rotate, so press it to start. Just press it, and at this time, Haier's automatic washing machine XQG60 B1287 will start draining.

6. When the water in the Haier automatic washing machine XQG60 B1287 is discharged, the Haier automatic washing machine XQG60 B1287 will pause for about five seconds, and at this time press the start pause button, at this time the Haier automatic washing machine XQG60 B1287 will stop working, and the drainage will be completed. Finally, press the "Power" key to turn off the power.

Water Discharge Steps:

1: See the control panel of the fully automatic washing machine, find the power button, and turn on the power of the washing machine.

2: Set the dehydration program, press the program button continuously, and select the washing machine program to the dehydration program. If you want to make the dehydration time longer, you can press and hold on the appointment time to change it, but most of the washing machines automatically set the time is sufficient.

3: Then, click the Start Pause button to start the washing machine program. The washing machine began to work on dehydration.

4: Pay attention not to open the lid of the washing machine during the dehydration process to avoid throwing clothes and hurting people.

5: Wait for the dehydration to be completed, the washing machine will automatically cut off the power to stop, and we can take out the laundry to dry.

Washing machine does not dehydrate reasons:

1) The washing machine panel door is not closed well or the switch of the top cover is damaged, it may also be that the switch is in poor contact, the washing machine is not allowed to open the top cover because it is a high-speed action when dehydrating, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the cover circuit is opened. If it is damaged and dehydrated, it will not move!

2) The drainage system of the washing machine is blocked or the drain valve is broken, the washing liquid in the water cylinder cannot be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

3) The drain valve does not open the clutch conversion, and the washing and dewatering of the automatic washing machine is completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally!

4) Poor motor performance and capacitance problems, resulting in insufficient output power, can be solved by replacing the capacitor.

5) Computer CMOS? rom?The curing program is damaged and cannot enter the dehydration process. In this case, this can replace the panel.

6) The fastening screws of the inner barrel of the washing machine are loose, or the bottom bracket of the inner barrel of the washing machine is damaged. If this is the case, in most cases, an empty washing machine can be dehydrated.

7) The washing and dewatering of the fully automatic washing machine is completed by the solenoid valve converting the gear at the bottom, and the damage of the solenoid valve will also make the dehydration unable to operate normally!

The reasons for not draining the water are: the program is not selected correctly: the washing program is not included in the washing program, and the washing machine can only be properly drained after rinsing or spinning.

Drainage pipe placement: If the water pipe is squeezed or bent, it cannot be drained normally, and it cannot be inserted into the floor drain too deep, which is easy to block, and sometimes there is an E1 alarm.

Whether the drain pipe of the upper drain washing machine is higher than 120cm, the drain pipe should be adjusted to between 80---100cm.

The discharge of water from the automatic washing machine is automatic, if it cannot be dehydrated, it can be operated according to the following steps:

1: Turn on the power of the washing machine.

2: Press the setting button continuously to select the washing machine program to the spinning program.

3: Then, click the Start Pause button to start the washing machine program. The washing machine started to drain the water.

Under normal circumstances, dehydration may begin after the water is discharged, if the water cannot be discharged, it may be that the outlet valve is broken, you can ask the maintenance personnel to come to the door for testing, or directly call the after-sales ** treatment.

Make sure to connect the water pipe, turn on the faucet, connect the power, put in the clothes, pour in the laundry detergent, press "start", about an hour, OK! Take out the dried clothes and dry them!

Small problems, look for after-sales to show you, you can also plan to spend consultation, 4006999999 call Haier's general customer service.

Summary. Kiss. Hello.

The laundry detergent of this Haier washing machine can be placed on the left or right side of the laundry detergent box, the laundry detergent box is generally divided into 3 area boxes, the left one is generally the main washing box, which is used to add laundry detergent, laundry detergent, etc., the box is deeper, and the number of times it is used is more, generally with"2"icon. The box in the middle is a care box, which is used to put softener or bleach, and the box is shallow and infrequent to use, generally like"Plum blossoms"icon. The box on the right is a pre-washed box, which is used as a pre-added laundry detergent, laundry detergent, etc., the box is shallow and less used, and is only used in the scheduled laundry program, which is generally like"1"icon.

Kiss. Hello. The laundry detergent of this Haier washing machine can be placed on the left or right side of the laundry detergent box, the laundry detergent box is generally divided into 3 area boxes, the left one is generally the main washing box, which is used to add laundry detergent, laundry detergent, etc., the box is deeper, and the number of times it is used is more, generally with"2"icon.

The box in the middle is a care box, which is used to put softener or bleach, and the box is shallow and infrequent to use, generally like"Plum blossoms"icon. The box on the right is a pre-washed box, which is used as a pre-added laundry detergent, laundry detergent, etc., the box is shallow and less used, and is only used in the scheduled laundry program, which is generally like"1"icon.

Kiss. Hello. Take a look at this, pro.

None of them. Kiss. You see. You take a picture of this, I'll take a look at it. Thank you.

Kiss. Hello. Isn't this a plum blossom? The first is to put the pro of the main lotion.

Is l one. Which is 1

Kiss. Yes, the one with the flower is put the pre-wash pro. Put the fabric softener on top.

The pro-l l is the first is the main baptism.

Kiss. Have a great day. All the best! 

Hello, how to use the detergent box of the xqg100 Haier drum washing machine: The detergent box of the drum washing machine generally has 2 to 3 small compartments, which are used to place detergents, softeners and disinfectants respectively. The label "1" or " in the small box indicates that laundry detergent has been added to this grid.

The small grid is marked with " " to indicate that the softener is added to this grid. The other compartments are used to add disinfectants, and you can distinguish detergents. When the laundry program starts with the water intake, the liquids in the different compartments will enter the drum with the water to better clean the laundry.

Be careful not to misplace laundry detergent and fabric softener, if you put laundry detergent in the fabric softener compartment, it will cause a large amount of laundry detergent to be left in the laundry. In addition, the softener should not be added too much, and there will be a maximum amount in this grid, which cannot exceed the "max" marking line.

Summary. Where to put the detergent of Haier washing machine XQG100-B12826U1.

It's this washing machine.

The small drawer in the upper left corner is usually visible when you pull it out.

Haier XQG60 a QHZB1287 washing does not run Hello dear, the capacitor is damaged, when the capacitor of the washing machine fails, the washing machine cannot work and wash normally. At this time, it is necessary to replace the capacitor with a new capacitor to restore the washing machine to normal. Motor coil cord is damagedWhen the coil cord set fails, the motor cannot work properly and the washing machine cannot be washed.

At this time, it is necessary to rearrange the coil assembly or replace the new motor to truly solve the problem that the washing machine cannot be washed. When the water level sensor fails, when there is a problem with the water level sensor, it will directly affect the operation and washing of the washing machine. At this time, it is necessary to replace the new sensor Jane's device to effectively solve the problem of the washing machine not washing.

The washing machine is unstable, when the position of the washing machine is uneven and unstable, it will automatically adjust to the rinse mode, resulting in the phenomenon that the washing machine is not washed. At this point, simply place the washing machine horizontally and set the land barrier back to wash mode. The drain is clogged, and when the drain of the washing machine is clogged, it will also cause the phenomenon of not washing.

At this time, it is necessary to inspect and dredge the water outlet to restore it to normal. Hope mine is helpful to you, thank you and have a great day!