The computer is taken and reinstalled by the person who repaired the computer. Now you have to press

Boss detection error may have a soft zone enabled. The following describes how to close it.

After turning on the computer or restarting the computer, "waiting...... is displayed on the screen, press the "del" key to enter the CMOS setup screen (Figure 1). Note that if you press too late, the computer will boot up the system, and the only way to do this is to restart the computer. You can press and hold the delete key immediately after powering on until you enter CMOS.

Once inside, you can use the arrow keys to move the cursor to select options on the CMOS settings interface, then press Enter to enter the submenu, use the ESC key to return to the parent menu, use the Page Up and Page Down keys to select specific options, and the F10 key to keep and exit the BIOS settings.

This one! Standard CMOS Setup is used to set the date, time, floppy drive specifications, job type, and monitor type.

There's an option! Change it to off

Don't listen to that person fool you As long as the fan is well maintained, there is no dust, there is no limit on the service life, and the power on press F1 is because of the floppy drive and keyboard boot settings of your BIOS settings Turn that off.

Is it a desktop computer? If it is, you are washed.

Try replacing the motherboard battery and good luck.

Method: 1. Turn off the floppy drive (the most common reason).

Generally, there is no floppy drive on the computer now, but as long as the computer BIOS is set up with a floppy drive to start, this leads to pressing F1 to continue.

Solution: Restart the computer, press del to enter the BIOS, find the standard CMOS setup, press enter in the open interface, change drive A: and driveb: to none, set floopy to disable, press esc, F10, Y, press enter to save and exit the settings.

2. Restore or optimize BIOS settings.

After turning on your computer or restarting your computer, "CD...... is displayed on the screen, press the "DEL" key to enter the BIOS settings interface, award

Load BIOS defaults, this option is used to load the BIOS initial settings to determine the scope of the failure.

Load Oprimum Settings, which are optimized settings for the factory BIOS.

or AMLLOAD BIOS Setup Defaults, which is used to load the BIOS initial settings.

Load High Performance Defaults, which is used to load BIOS optimization settings.

After selecting the default or optimized value with the keyboard arrow keys, press Esc, F10, Y, press Enter, Save and exit the setting.

3. Set the hard disk as the first boot. Reboot, press del to enter the BIOS, find the Advanced BIOS Features (advanced BIOS parameter settings), press enter to enter the Advanced BIOS Features interface, and set the First Boot Device to HDD-O (hard disk boot).

4. If the motherboard battery is out of power, it will also cause data loss and this fault will occur, check and replace the motherboard battery.

You can try these methods and see if they can solve the problem.

Note: In general, the first method will solve the problem.

The motherboard battery is dead, spend two yuan to buy a 2032 battery, replace it and reset the BIOS to disable the floppy drive.

Generally, you set up a floppy driver, but the floppy drive does not, go into the BIOS, and boot the hard disk to boot up.

Sometimes it's also because of the battery, after each setting, the computer is turned off and the soft boot resumes.

Common BIOS are, F1, F2, F10, F12, Del Of course, to install the system, you can also install a virtual optical drive, load it into a virtual optical drive for installation, and you can also make a bootable U disk. Install with U disk, ISO is a disc image file, the system image can be burned into a system CD, used when reinstalling the system, you can also use the RAR compressed file to decompress the GHO file and one-click backup and recovery software to the hard disk, and then use the one-click backup and recovery software to load the GHO file to install.

The electronics of the motherboard is out of power, so go to the store and change it for about 5 yuan.

First, this is not a problem with reinstalling the system, so don't reinstall the system in the future when you encounter such a situation Second, this is a problem with BIOS (or CMOS), please follow the prompts to enter the BIOS (usually press the DEL key or F2 key), see if there is a problem with the time setting or set the floppy drive to start, adjust it according to your machine situation, and restart it after saving.

Third, some assembly machines use a special CPU for mobile PCs, and you must press F1 when you turn it on, so there is no way.

Fourth, if you don't know how to set up BIOS, please ask a knowledgeable friend to help

If F1 indicates that the computer has not passed the self-test, you can confirm the cause according to its English prompt, such as: CPU Fun Error, Pleases Press F1 to Setup

If you don't know how to tell, you can go to the BIOS and turn off the wait for F1 if error prompt function, usually under the boot option.

If it is not possible to build a test, the minimum system method will determine where the fault is.

Reason to start to press f1:

1. If the motherboard battery is out of power, it will also cause data loss, which will cause this failure.

2. In fact, there is no floppy drive or the floppy drive is broken, but there is a floppy drive in the BIOS, which leads to pressing F1 to continue.

3. There are some small errors in the system settings, and they have not been corrected, so it is recommended to turn off the prompt.

The workaround to solve several problems is roughly as follows:

1. If the motherboard battery is dead, you can change the motherboard battery, and another way to judge the motherboard battery is to enter the system to see if the system time is consistent with the actual time.

Second, there are several problems with floppy drives, and there are several solutions.

1. Reboot the system, enter the BIOS settings, if you find that the floppy drive is set to, but there is actually no floppy drive, you need to replace the auto of the idesecondary master with none.

2. Press del to enter the motherboard BIOS at boot, enter the boot startup item to set the boot boot sequence, and turn off the floppy drive to boot.

3. You can also turn off the boot detection function. Start the computer, and then press the DEL key to enter the main interface of the motherboard BIOS settings; Select the "Advanced BIOS Features" setting item to enter; Set "Boot Up Floppy Seek" to "disabled" to turn off boot software detection.

The above information is taken from the official website of Xiaobai System, and the detailed content can be found in it.

To press F1 to start, there are generally two situations, one is that the motherboard battery is dead, you can change the battery, the electronic market is sold, R2032, about 5 yuan. The second is that the BIOS of old-fashioned computers boots a floppy drive by default, but many computers do not have a floppy drive, which may make you press F1 to skip.

In the first case, try changing the battery.

The installation system can't solve it.

Need to go into the BIOS

Set it up. I turn off DRIVEA (floppy drive).

Generally fine.

If that doesn't work, replace the CMOS battery.

The button-sized one).

First of all, is the time you look at the machine at the wrong time, if so, please change the battery of the motherboard.

If not, press the Del button after booting up to enter the BIOS interface, generally find the Floppy option in the first option on the left, and select it as None.

Then find Frist

bootdevice option, harddisk is selected. (This option is usually in the second or third option on the left).

Save and exit on it.

1.Not necessarily, the advanced BIOS turned off the floppy drive and pressed F10 to save, then unplugged the host power, waited for a minute or two, and then turned on the computer If it shows F1 again, it means that the motherboard BIOS chip battery is dead, if not, then there is still power, sometimes it is not shut down normally, or what is modified in the system will be like this.

2.Replace the motherboard battery to protect the motherboard's power-on status. After entering the BIOS to change the floppy drive to the off state, as long as you keep the motherboard powered on (even if it is not turned on), it will not be prompted again.

If the power is off.

It will be reprompted immediately.

3.Two ways to reboot, press Del into BIOS, find StandardCMOSSETUP, press enter in the open interface, and set DriveA: and DriveB:

Change to none, set Floopy to Disable, press ESC, F10, Y, press Enter to save and exit the settings. The motherboard battery is dead, just replace the battery.

Hello red, I hope you take a closer look below, maybe you can find the reason from it, and I hope you will solve it yourself in the future.

The machine needs to press the F1 key to enter, mainly because the settings in the BIOS do not match the real hardware data, which can be divided into the following situations:

Under normal circumstances, the requirement to press F1 to enter the system is caused by a minor problem with the system's BIOS settings that do not affect the system startup, so please check the hardware information settings in the BIOS for discrepancies with the actual situation.

The common faults in general are:

1. The battery on the motherboard is dead.

Solution: Replace the motherboard battery.

2. You have set up the floppy drive to start, but there is a problem with your floppy drive.

Solution: A. Press del to enter the BIOS at boot, boot up the boot sequence, and turn off the floppy drive to boot.

b. Turn off the detection function of the floppy drive when it is turned on

Start the computer and press the [DEL] button to enter the main BIOS settings interface.

Select "Advanced."

biosfeatures", press the enter key to enter;

Add "boot

upfloppy

seek" is set to "disabled", so that the boot software detection function can be disabled.

A. Press DEL to enter the BIOS at boot, boot up the boot sequence, and turn off the floppy drive to start.

b. Turn off the detection function of the floppy drive when it is turned on

Start the computer and press the [DEL] button to enter the main BIOS settings interface.

Select "Advanced."

biosfeatures", press the enter key to enter;

Add "boot

upfloppy

seek" to "disabled", which turns off the reference:

It may be that you don't use your computer for a long time, and we have one in the Internet café.

Don't be afraid, it's not a big deal.

You take your motherboard and blow it, and plug in the hard drive cable tightly.

The motherboard coms battery is dead, just go to the place where the computer accessories are sold and buy one.

It's like reinstalling a one-poop system, it's outrageous.

It should be that the computer is set up to boot the floppy disk.。。 No problem.

Block the floppy drive in the BIOS settings.

Press the del button when you boot it up (some motherboards press F2), and after entering the BIOS, look at the drive A option in the CMOS.

Change the option to none

After changing it, press F10 to save. Select"y

That's when you changed the settings of the motherboard, and you just reset the host parameters to the default values.