-
Anonymous users2024-02-08Didn't you buy it new, go back to him, he gave you a match, pit people, the problem with the display card.
It's not that the graphics card is old and not good, or he has assigned you a graphics card that doesn't match the motherboard, or it's a problem with the graphics card driver, have you driven the graphics card driver?
The driver must be installed correctly, the boss graphics card, the driver you installed the wrong one, and what is the difference between not installing the graphics card Update the driver and try it
1. It is suspected that it is a heat dissipation problem.
Check method: ** An everest, run, in the "Sensor" column you can view the graphics card and CPU temperature, CPU fan speed, etc. Cut out while playing 3D games to see what the temperature is. Or after running everest, the temperature will be displayed in the tray area, then run the 3DMark software, and observe the temperature displayed in the tray area in the lower right corner when the screen is switched.
Generally, the CPU does not exceed 60 and the graphics card does not exceed 70, and it may be a heat dissipation problem if it approaches or exceeds this value.
Solution: Replace the radiator fan.
2. Power failure leads to problems with other components.
Check: The 6600 AGP version graphics card should also have a 4-port power supply, check whether the wiring is good. Replace the power supply with another power supply for the boot test.
But personally, I think it's unlikely that it's a power supply problem, at least it's certainly not a matter of power. My X1600Pro and Barton2500+ only use Huntkey Calm King 300W, and your CPU power consumption is lower than mine.
Solution: Replace the power supply and try it.
3. Memory problems:
Unplug a memory and start it up to see if the problem persists.
Solved: Replace the problematic strip.
It shouldn't be a driver problem, the hardware problem is more likely to be lower.
There are many reasons for a web page to get stuck or a memory error, the former is usually due to a virus or a small disk cache, and the latter can be a virus, a hardware problem, or a normal temporary software conflict.
-
Anonymous users2024-02-07Blurred screen ??? What kind of flowers do you have?
-
Anonymous users2024-02-06Computer Blur Screen Solution:
1. Set the BIOS to factory default.
2. Remove the memory, use the eraser gold finger, clean the motherboard memory slot, increase the setting of virtual memory, and set the virtual memory to a partition with a large space outside the C drive.
3. It is an independent graphics card, remove the graphics card, wipe the gold finger, clean the slot, and then install it and plug it in tightly.
4. Check whether there is any problem with the monitor, plug in the data connection of the monitor with the graphics card, and tighten the screws.
5. Check the heat dissipation of the CPU and graphics card, dust and oil the fan, or replace the fan.
6. Set the desktop and screensaver to none, and do not have more than 10 desktop icons.
-
Anonymous users2024-02-05DNF blurred screen solution: staring generally after holding down Ctrl+Alt+Del, it will return to normal. If ctrl+alt+del doesn't work, you'll have to find out why.
Display Huachang is an extremely common failure,There are many reasons,The fault phenomenon caused by different reasons is also different in terms of coarse resistance,The solutions are also different。 Common faults include graphics card driver, power supply, cable, display, and graphics card faults.
-
Anonymous users2024-02-04Discrete graphics cards are very good, please don't change the integrated ones at will!
It may be a driver problem, it is recommended to install a driver wizard to detect!
The graphics card is not low, it is estimated that there is too much ash on the fan of your graphics card, which is caused by the high temperature of the graphics card, you try to unplug the graphics card and then sweep the dust on the fan, and then wipe the metal inserts of the graphics card with alcohol or an eraser, it is estimated that it will be fine, because I have had this problem before, and I have not used the above method again!
If you estimate all the tasks, you can upgrade to one level by brushing them once. The fast ones can be upgraded by two levels.
I don't know if you're a businessman who often makes drawings. If so, I can use all of these things, just like a mage's blood can be exchanged for a lowest-level hardener (the lowest hardener is very useful, for awakening quests, and for normal quests. ), the Minotaur's hard horn can also be changed in Daphneli. >>>More
Drift is the network delay caused by the network connection.,It has nothing to do with your machine.,For example, you beat a monster to death.,But the people who team up with you still see the monster.,But just can't hit it.,Then you see the phenomenon of your card.,After a smooth connection, the picture of you hitting the monster will be on their screen.,Of course, what you see is definitely different from what you see.,It's a doubled ** picture.,Very fast.,So it feels like it's floating.,PK is often encountered.。 In short, the card is a tx problem, don't scold other people's cards or feel that something is wrong.
Halalz, I was wrong... It's so many words that I found out that my eyes were broken. I didn't see it clearly.,I'm sorry.。。 >>>More