What is the high and low temperature and low pressure test chamber used for?

It is mainly used to determine the environmental adaptability of instrumentation, electrical products, materials, parts, equipment, etc. under low pressure, high temperature, low temperature single item or at the same time.

to test one of his ones. Low temperatures, high temperatures, and one of his air pressures.

Audi question, what the air pressure test chamber is used for, what this air pressure test chamber is used for, I don't know so clearly.

High and low temperature and low air pressure are experimental supplies used to change the temperature of the relatively low air pressure to make some experiments.

This equipment is not only suitable for military testing, but also for automotive testing in alpine environmental conditions, and for testing computers, electronic components and packaging that may need to be transported by air. Such tests often require analogies of multiple environmental conditions, and a low-pressure test chamber can combine these environmental conditions and simulate changes in gas pressure and temperature. Most of the low-pressure test chambers are pumped out of the gas in the chamber by vacuum pumps, 22 Suzhou-Zhou-Zhong-Chuang-League-Laboratory-Laboratory-Technology-Technology with a unique frequency conversion control can control the pressure and temperature at an equal slope, which is more in line with the real situation, and the volume of the standard low-pressure chamber is from cubic meters to 6 cubic meters.

A typical requirement for a standard low pressure test is 30,000 feet (10 km), while our equipment can meet the low pressure requirement of 100,000 feet (30 km). For high and low temperature and low pressure test chambers, please find Suzhou Zhongchuang Alliance Laboratory Technology.

For high and low temperature and low pressure test chambers, please choose Suzhou Zhongchuangmeng Laboratory, rich experience in equipment research and development, and professional equipment maintenance personnel, to bring you a perfect experience.

Parameters of high and low temperature and low pressure test chamber of Zhongchuang Alliance laboratory.

1.Internal dimension(w*d*h mm):500*600*750;700*800*900；1000*1000*1000

2.Temperature range: -70 +150 (A:0 B:-40) C-40 D-70).

3.Temperature and humidity analysis accuracy Distribution accuracy: ; 2℃；±3%

4.Pressure range: atmospheric pressure 1kpa (adjustable).

5.Pressure deviation: kpa) 01kpa(4kpa).

8.Exterior material: high-quality steel plate + powder spraying.

9.Inner box material: stainless steel, reinforced inside.

10.Insulation material: high-temperature resistant high-density polyurethane foam insulation material.

11.Protection devices: fuseless switch, compressor overload protection switch, refrigerant high and low voltage protection switch, over-humidity and over-temperature protection switch, fuse, fault warning system.

12.Accessories: Recorder (optional), observation window, 500mm test hole, PL box inner lamp, stainless steel partition, wet and dry ball gauze.

13.Controller: independent research and development.

14.Compressors: French "Taikang" brand German "GEA Blog".

15.Power supply: AC220V 50Hz 60Hz AC380V 50Hz 60Hz

16.Features: Adopt cold end control, low temperature constant temperature is not heated, linear cooling is not heated, energy saving can be more than 40%, water saving 50%.

High and low temperature test chamber brand manufacturers also need to pay special attention to a lot of details in use, otherwise it will also have some impact on the production of its products, with the long-term use of the test chamber also need to pay attention to the usual repair and maintenance, let's take a look at some of the things that need special attention in its use.

1. Humidity and temperature.

Manufacturers of high and low temperature test chambers need to control the temperature and humidity in special use in use, because the temperature and humidity will affect the performance of the devices in the test chamber, and will cause corrosion of many parts of the instrument for a long time.

2. Dust. With the long-term use of the experimental chamber will also accumulate some dust, at this time users need to use the electric constant temperature drying oven to remove dust work, we all know that the radiator has a heating element in use, if it is covered with a lot of dust, it will cause the accuracy of the use of extremely parts, affecting the standard of the entire processing and production.

In addition, users also need to operate in strict accordance with the instructions when operating and using high and low temperature test chamber brand manufacturers, and the operators need to be very familiar with the overall structure and operation process of the test chamber to ensure the normal operation of the test chamber.