What is the reason for E2 after the washing machine is pressed to start?

This is supposed to show up incorrectly** may be caused by not closing the lid properly, you check it out.

There are two possible faults in the washing machine with E2:

1. Because the upper cover is not covered, you can open it to check whether there is a big beard and clothes clamped, or other foreign objects that affect the normal closure of the cover.

2. Because of the overtime of drainage, you can check whether the drainage pipe is deformed or twisted; Check that the drain pipe is unblocked and that there are no foreign objects blocking the drain pipe.

The troubleshooting method of washing machine can not be dehydrated is as follows:

1. The washing material is in a state of rolling imbalance during washing. Elimination method: You can put a small amount of clothes before washing clothes, and don't stuff too much at once, so as not to cause imbalance during washing. And the effect of dehydration is not good.

2. The safety switch on the top cover of the washing machine is damaged. Try not to open the top cover during the dehydration process to avoid damage to the top linkage switch.

3. The drainage system of the washing machine is blocked. Removal method: remove the drain filter for cleaning, flush the drain with water and remove the debris in the drain valve.

4. The water level switch cannot be reset. Solution: Contact the after-sales point.

Summary. You can do the investigation according to the above reasons: 1. First check whether the drain pipe of the washing machine is put down and whether the drain pipe is blocked; 2. Reopen the washing machine door to make sure that no clothes are stuck, and then close the washing machine door with appropriate force; 3. Shake the clothes and put them in and don't put too much at one time to avoid imbalance; 4. After the above investigation, restart the washing machine and observe whether it returns to normal.

Sorry to keep you waiting.

The laundry potato imitation surplus machine displays a large E2 fault code, which may be due to the following factors: 1. Drainage timeout; 2. The washing machine door is not closed properly; 3. Unbalanced laundry; 4. The top cover switch of the washing machine is damaged.

You can do the investigation according to the above reasons: 1. Check whether the key of the drainage pipe of the washing machine is quietly put down and whether the drainage pipe is blocked; 2. Reopen the washing machine door to make sure that no clothes are stuck, and then close the washing machine door with appropriate force; 3. Shake the clothes into it and don't put too much of it at one time to avoid imbalance; 4. After the above investigation, restart the washing machine and observe whether it returns to normal.

If it is still not restored, you need to find a professional maintenance personnel to come to the repair, you can call 400-039-2926 to make an appointment with a master near you.

It refers to the overtime of draining (if the water is drained for more than 6 minutes, the alarm can be lifted by opening and closing the door cover once).

Under normal circumstances, if the washing machine is drained for more than six minutes, this fault alarm will appear. For such malfunctions, the alarm can be lifted by opening and closing the lid of the washing machine only once. But it still can't be solved, so check if the drain pipe is down or deformed, and if so, put it down or replace it.

Possible Causes:

The drain pipe is not lowered, resulting in the water not being drained;

The drain pipe is deformed or twisted, resulting in excessive drainage time;

The drain valve is clogged and the water cannot be discharged;

There is a problem with the circuit, etc.

Troubleshooting of washing machines that cannot be dehydrated.

The laundry is in an unbalanced state during the washing process. Elimination: Before washing, you can put less clothes, don't stuff too much at once, so as not to cause an imbalance in washing. But the dehydration effect is not good.

The safety switch on the top cover of the washing machine is damaged. During the dehydration process, try not to open the top cover, so as not to damage the top linkage switch.

Clogged laundry drainage. Method: Remove the drain filter for cleaning, flush the drain with water to remove debris in the drain valve.

The water level switch cannot be reset. Solution: Contact the after-sales point.

The washing machine could not be dehydrated due to a faulty motor. Method: Try opening the back cover of the washing machine and moving the pulley by hand if it doesn't get stuck.

When the power is turned on and the motor hums, but does not rotate, it means that the motor is short-circuited or damaged, or the motor circuit is not connected to the capacitor. At this point, cut off the power supply, remove the motor belt, and restart. If the motor still does not rotate or the speed is low, it is a motor failure and the motor should be repaired or replaced.

1. The specific treatment method of the washing machine display E2: unscrew 4 screws (one on the left and right, two in the back), and turn the control plate seat cover on the washing machine upside down. Open the plastic plywood inside the control panel base to reveal the control switch inside, and check if the switch can be closed.

If you can close it, remove the switch of the double copper plate, polish the two contacts with sandpaper or sand paper, remove the obstruction of the contact points, and make them contact well.

2. The failure of the washing machine E2 is generally caused by the following situations: the drainage time is too long. You can first check whether the upper cover of the washing machine is properly covered.

Check whether the drain is unobstructed, if the drain is small, it may be that the drain is blocked with foreign objects, just take it out. Check to see if the drain motor is damaged.

Summary. For different brands and models of washing machines, the display of E2 indicates that the reason is different. However, most washing machines have E2 because there is no water in the washing machine, or the lid of the washing machine is not changed, or the water outlet is blocked.

For washing machines of different brands and models, the display of E2 indicates that the reason for the quiet key is different. However, most of the e2 is due to the fact that there is no water in the washing machine, or the lid of the washing machine is not changed, or the water outlet is blocked.

If there is a washing machine E2, you can check the faucet to see if the drain pipe is flattened, or if there is a blockage, you need to deal with it, and you can use it. If there is no problem with drainage, check whether the door of the washing machine is closed and whether the wiring of the switch is loose.

If the individual can't find the problem of the lack of a large washing machine, you need to contact a professional to deal with it, and the individual must not force the sun to disassemble the washing machine, otherwise it will lead to greater damage.

2. How to use the washing machine correctly 1. Plug in the power supply of the laundry, open the lid of the washing machine, and then stuff the clothes that need to be cleaned into the washing machine. 2. According to the amount of clothes to be washed, add an appropriate amount of cleaning liquid, and in the case of general eggplant, add half a cup of cleaning liquid.

Then after setting it, you can let it be automatically cleaned, no need to do other operations, just wait until it is washed, and dry the clothes, which is very convenient.