How to disassemble the main door panel of the 19 Tuyue?

1) Prepare tools and work carts or work benches.

2) Open the door to the maximum to make it easier to operate the hinged support, place a bracket on the lower edge of the door to support the weight of the door and protect the door, and unscrew the window glass. In this example, the rear door is mainly disassembled, such as the front door to remove the exterior mirror. 3) Disassemble the door and body wire connectors to separate the door wiring harness.

If necessary, remove the inner trim on the column first. ▼

4) Remove the clip at the bottom of the door limiter stop lock pin and pull the lock pin out of the hole. ▼

5) Hold on to the door and remove the door hinge bearing connecting bolts. Remove the door and place it vertically on a padded surface. If you only need to remove the door for repair, it is recommended to remove the hinge connection bolts instead of the fixing bolts to remove the door, which will reduce the need for door adjustments.

6) Check the casing of the door chain, replace it if necessary, lubricate the hinges, put the door back on the hinge support, and reinstall the bolts. ▼

7) Connect the door limiter, install the stop lock pin and lock tab, and connect the wire plug. ▼

8) Close the door, check whether it is aligned, correct it if necessary, and tighten the hinge fixing bolt if there is no problem. ▼

9) Note that if the front door is disassembled, the rearview mirror needs to be installed.

There are screws in the buckle handle, as well as the horn and inner handle, and look at the interior panel to see if there are any screws.

1. Use a small knife to uncover the small cover plate in the groove of the driver's door panel.

2. Use a Phillips screwdriver.

Remove the screws.

3. Remove the triangular cover behind the driver's rearview mirror.

4. Use a flathead screwdriver to pry up the door panel of the driver's seat and make the door panel break free from the buckle.

5. Remove the glass lift switch plug from the driver's door panel.

6. Unplug the rearview mirror adjustment switch of the driver's door panel, and detach the handle cable from the door.

7. Finally, the door panel can be completely separated from the empty town with resistance.

Summary. I have a 2019 Tuyue, and I once tried to remove the top plate from the trunk, but it didn't work. SolutionAccording to my personal experience, the plate on the trunk of the 2019 Tuyue cannot be removed.

However, if you want to remove the plate on the trunk, you can try to ask the master for help at the 4S shop, as they have professional tools and techniques that can better help you solve the problem. Expansion: In addition, if you want to replace the plate on the trunk, you can buy a new board at the 4S store and ask the master to help install it.

I have a 2019 Tuyue, and I once tried to remove the top plate from the trunk, but it didn't work. According to my personal experience, the plate on the trunk of the 2019 Tuyue cannot be removed. However, if you want to remove the plate on the trunk, you can try to ask the master for help at the 4S shop, because they have professional tools and techniques, and Closed Pure Attack can better help you solve the problem.

Expansion: In addition, if you want to replace the plate on the trunk, you can buy a new board at the 4S shop, and then ask the master to help install it.

You've done a great job! Can you elaborate on that?

For your problem, we recommend that you try to disassemble the plate on the trunk, but it should be noted that you should confirm whether there are installation instructions before dismantling to avoid damage. In addition, you can also consult your local 4S store, they will be more professional to help you solve the problem. I hope I can help you.

Summary. First of all, we have to open it, and then unscrew the screws of the interior panel from the inside, and we can take it off directly.

First of all, we have to open it, and then unscrew the screws of the interior panel from the inside, and we can take it off directly.

The following are the dismantling steps of the door trim panel: 1. Open the door to be disassembled, and disassemble the handle decoration in the door; 2. Use a small word change cone to reach into the gap between the decorative cover and the inner handle, and gently pry and pry open the clip inside; 3. Disassemble the screws that fix the door trim panel at the inner handle and disassemble the screws with T-30 splines. Here's how to disassemble the parts that hold the door trim panels:

1. Dismantle the screws under the fixed door trim panel: There are two plastic pattern screws below that do not need to be disassembled to fix the door trim panel, and the T-30 spline can be taken out and twisted 90 degrees clockwise. 2. Dismantle and solve the buckle of the fixed door trim panel

Take the inspection accompaniment to the large word change cone and use it to pry up the gap between the edge of the door panel and the door trim panel. Pry the inside clips open one by one and separate them from the door panel. Pay attention to prying slowly to avoid prying the clip and scratching the door panel.

After prying all the clips, hold the left side of the door trim panel with your left hand. Hold the right side of the door trim panel with your right hand and gently pull it outward, tentatively with force. Until the door trim panels are separated from the door panels.

In the same way, hold the left and right sides of the door trim panel with your hands and lift it up. After completely detaching, unplug the wiring harness inside by hand.