Computer maintenance, it seems that the solid state is not installed well today, and the machine can

After installing the SSD, the computer cannot be turned on for the following reasons:

1. The power supply of the laptop is insufficient, which is caused by excessive use of the laptop or excessive power consumption of the battery standby for a long time.

2. There is no response when the machine is turned on, and the most common situation in this kind of situation is loose hardware or water ingress into the notebook.

3. When booting up, it prompts that the serial port, parallel port, hard disk, etc. cannot be recognized, which is generally caused by loose hardware or COMS data errors.

After installing the SSD, the solution to the computer cannot be turned on and touched by the machine is as follows:

1. Restart the computer first, then press the DEL key when the computer is turned on to enter the BIOS setting interface, or press F2 here, then open the BIOS setting interface, select Advance, and then select Integrated, Peripherals and click Enter below.

2. After selecting the integrated and peripherals options, you can find the onboard, lan, option, and rom options in the window that appears, which is the network card boot rom setting option, and change the status behind it to disable.

3. After completing the above settings, press F10 directly on the keyboard to save the settings, and then restart the computer, and the problem of not being able to turn on can be solved. <>

It is possible that there is a problem with the hard disk, and the system has an error when it self-checks the hard disk, and it is frozen.

You can not connect this hard disk first, use the original mechanical hard disk to boot the system to the desktop, and then connect to this solid state drive, see if it can be recognized normally, can partition and format, and you can also use hard disk detection software to detect whether there is a problem with the hard disk.

If it can be recognized normally in the Windows environment, can be used normally after formatting, and the problem cannot be detected, it should be fine. If it can't be passed, it means that it is bad, and the return should be hurried. Of course, it may also be a problem with the motherboard's interface and cables, although it is less likely, it should also be ruled out.

If you can't turn on the SSD after installing it, it may be caused by hardware compatibility, BIOS settings, poor connection, etc. Here are some common workarounds:1

Confirm hardware compatibility: First, confirm whether the SSD is compatible with the motherboard and operating system of the computer, and check whether the specifications of the hard disk match the specifications of the motherboard. Compatibility can also be improved by updating the motherboard's BIOS or drivers.

2.Check the connections: Make sure that the SSD is securely and correctly connected to the motherboard and power supply, especially the SATA cable and SATA power cable.

First, you can try setting the SSD as the "Preferred Boot Device" and then check that the motherboard's AHCI or IDE mode settings are correct; If you're not sure, you can try setting it to AHCI mode.

4.Reinstall the operating system: If the SSD still won't boot, you can try reinstalling the operating system. In the meantime, you can also use Windows PE or another startup disk to try to fix the hard drive boot issue.

5.Replace the SSD: If none of the above methods can solve the problem, you can try replacing the SSD to see if there is a problem with the hard drive itself.

In short, if you encounter a situation where the SSD cannot be turned on, you need to carefully check and try the above methods to solve the problem. If you really can't solve the problem, it is best to contact the hardware manufacturer or professional for repair.

There are many possible reasons why your computer won't turn on after installing a family line SSD, and here are some common solutions:

1.Check the cable: Make sure the cable between the SSD and the motherboard is plugged in tightly. You can also try replacing the cable to see if there is any improvement.

2.Check the settings: Check the boot sequence settings in your computer's BIOS to confirm that the SSD has been set as the first boot device. If it doesn't, move it to the top, save the settings and restart your PC.

3.Fix Boot: If the operating system in the SSD is damaged and the computer does not boot properly, you can use a Windows installation disk or recovery software to repair or reinstall the system.

4.Update BIOS: If your PC's BIOS version is outdated, it may cause your SSD to not boot properly. Try updating your PC's BIOS version to support SSDs.

5.Check the power supply of Hesuiling: Check whether the power supply is normal, if the power supply is insufficient or there is a problem with the power cord, it may cause the computer to fail to start normally.

If the above methods do not solve the problem, you may need to further detect the problem with the computer hardware and software. It is recommended to find a professional for overhaul and treatment.

There may be several scenarios:1Failure to properly install a solid cavity hard drive causes the computer to not recognize the new hard drive

You can check that the SSD has been properly connected to the computer motherboard and that it is correctly recognized. 2.Incorrect BIOS settings:

You can go into your computer's BIOS and check that the SSD is correctly set up as the boot disk. If you don't set up your startup disk, your computer won't boot from the SSD. 3.

Operating system issues: If you replace your SSD without reinstalling the operating system or cloning the operating system correctly, it can cause your computer to fail to boot. 4.

Hardware failure: If your computer won't boot after replacing your SSD, it may be because other hardware is faulty and needs to be troubled. If none of the above methods can solve the problem, it is recommended to contact a professional maintenance personnel or computer manufacturer for further investigation and repair.

Summary. If you remove the SSD and install it back again and the computer won't turn on, there may be several reasons:1

Connection issues: Please check that the SSD is securely connected and that the connector is plugged in correctly. 2.

BIOS setup issues: Some computers need to set the boot sequence in the BIOS to ensure that the SSD is set as a boot device. 3.

Compatibility issues: The compatibility of an SSD with a computer can also cause it to not boot. Check that the SSD is compatible with your computer.

4.Reinstall and install the data port position chip to wipe clean to prevent dust.

The computer is good, after removing the SSD, it can't be turned on when it is installed back on.

If your computer won't turn on after removing the Kaizhou SSD and installing it back again, there may be several reasons:1Connectivity issues:

Please check that the SSD connection is secure and that the connector is plugged in correctly. 2.BIOS Setup Issues:

Some computers need to set the boot sequence in the BIOS to ensure that the SSD is set to boot as a boot device. 3.Compatibility Issues:

The compatibility of the SSD with the computer may also cause it to not boot. Check that the SSD is compatible with your computer. 4.

Reinstall and install the data port position chip to wipe it clean in case there is gray state Sun Bochen.

The screen is a blue screen with some English letters.

Dear, in this case, the Tan limb walked into the BIOS system, set the boot sequence in the BIOS, and make sure that the SSD Liang Xinpao is set to boot the device can be used normally.