New Focus, automatic gear hanging reverse gear suddenly did not respond, and after a while it was fi

It is recommended to go to the 4S store for inspection and deal with it according to the specific situation.

1. It may be the braking systemAutomaticElectronic linkage between gearboxes.

When shifting gears, the clutch does not step to the end, causing damage to the gears. In addition, the foot should not be placed on the clutch when the clutch is not in use, resulting in excessive wear of the release bearing.

Solution: Go to the 4S shop for inspection and repair.

2. It may be idle gear

In automatic transmission models, the engine revs very high in the first few seconds of engine starting, and if the engine revs have not dropped to a steady state, it will be put into gear.

Switching from neutral to reverse will bring strong shock vibrations to the gearbox, which will damage the shift switch in the gearbox. The scientific approach is to wait for the speed displayed in the instrument cluster to stabilize before using reverse.

Solution: When shifting gears, attention should be paid to the coordination of the clutch pedal, accelerator pedal, and gear lever. When shifting gears, the gear lever must be pushed firmly in place so that the gears are fully engaged so as not to damage the gears or transmission.

Automatic disengagement while the car is in motion.

Precautions for hanging reverse gear:

1.The car stops and then reverses.

The car has not completely stopped, the reverse gear is hung in, this is a lot of "old drivers" love to commit bad mistakes, it seems to be very skillful driving, in fact, this is very damaging to the gearbox, most of the family car reverse gear does not have a synchronizer, if you do not park the car to hang into the reverse gear to play the tooth is inevitable. Therefore, when hanging the reverse gear, we need to pay attention to the fact that we must step on the brakes and stop the car before hanging.

2.Clutch pedal to the bottom.

When stepping on the clutch in gear, you must step on the clutch to the end, and the clutch must not be semi-linked.

In addition, when hanging the reverse gear, you should be gentle, don't be too hard, so that you can occasionally hear the distressing gear impact.

3.Reversing should be slow.

Finally, the speed should not be too fast when reversing, do not step on the accelerator to accelerate the reversing sharply, which will cause great damage to the straight tooth wheel, and the transmission of the straight gear is very direct and the smoothness is poor, so the fast reversing will make the people in the car feel very uncomfortable, and the sound is not very good.

The above content reference: Encyclopedia - Changan Ford New Fokker.

The above content reference: People's Daily Online - Three tricks to teach you to get the inexplicable noise of the car It is very important to identify the cause.

The above content reference: Encyclopedia - Reverse gear.

Hello, this is a problem with the gearbox computer, it is recommended to go to the 4S shop for inspection, according to the specific situation to deal with, (gearbox computer upgrade,) if the fault occurs, it is best to use a mobile phone to record it, so as to reflect the problem with the 4S shop, and report to the manufacturer. [Car questions, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

A 4S shop that makes a living from scams!

Yesterday evening, the Focus at home suddenly did not reverse, and the results of online verification showed that this problem is a common problem with the car, and the computer module can be upgraded for free at the 4S store. Early this morning, I carefully drove the car to Zhengzhou Xicheng Tiandao 4S***, everything was handled according to the program, a young man in his twenties connected to the computer test for a few minutes, and pointed to the four words on the computer screen "replace the battery". I know that the child did the tricks but did not get angry, smiled and explained that there is a fault in the computer version of the tire, just upgrade and replace it, what does this have to do with the battery?

Moreover, this battery is also a 4S store that has only been replaced for a little more than a year. This young man is not an old fritter, he immediately lowered his head, but also stammered and defended: "The upgrade is free of 2000 yuan, and the battery must be replaced at the same time to completely solve the problem, and the voltage instability of the old battery affects the computer version" At this time, the 4S store used the defects of the car itself to cheat consumers by hitchhiking.

I was worried that unscrupulous businessmen would retaliate and do other things, so I had no choice but to accept it. At the same time, he specifically asked him if this could be completely solved? He immediately looked up and said yes!

I said that's fine, you can change it, but I'll take the old battery away! The child looked at me in a panic and said, "The old battery store will deal with it uniformly, give me a 50 yuan working hour coupon," and I refused.

After that, the child never dared to look up at me, acting as a child who had done something wrong, until I paid the fee and drove away. When I came back, I asked a friend to test the old battery, and everything was in good condition!

The reasons why the Focus automatic transmission can't hang the gear are: it may be that the gear switch of the automatic transmission is not opened, and it may be that the gearbox is faulty, and it is recommended to go to the 4S shop for inspection and maintenance as soon as possible.

Automatically save licaiying

The Ford Focus means focus, and it is one of the home models of Ford in Europe.

Focus has entered the Chinese market since the second generation of models, with sporty, handling and young and dynamic as the main image, and has achieved good results in the domestic compact model market.

The interior design of the new Focus is completely different from that of the old model, and if the interior of the old model is more about practicality, then the interior of the new Focus has more decorative elements. The interior design is full of three-dimensional lines, which make the interior of the new Focus look angular, but you don't have to worry about these edges and corners being as hard as they look, in fact, the interior materials of the New Focus are still very generous, and the interior assembly process has also been improved.

The reasons why the Focus automatic transmission can't hang the gear are: it may be that the gear switch of the automatic transmission is not opened, and it may be that the gearbox is faulty, and it is recommended to go to the 4S shop for inspection and maintenance as soon as possible. Autosave Licaiying Ford Focus means focus, and it is one of the home models of Ford in Europe.

Focus has entered the Chinese market since the second generation of models, with sporty, handling and young and dynamic as the main image, and has achieved good results in the domestic compact model market. The interior design of the new Focus is completely different from that of the old model, and if the interior of the old model is more about practicality, then the interior of the new Focus has more decorative elements. The interior design is full of three-dimensional lines, which make the interior of the new Focus look angular, but you don't have to worry about these edges and corners being as hard as they look, in fact, the interior materials of the New Focus are still very generous, and the interior assembly process has also been improved.

The new Focus is equipped with a low-speed driving safety system, which automatically brakes to a standstill when the vehicle is close to an obstacle in front of it at a speed of less than 20 km/h to prevent accidents caused by negligence (only available on sedan models).

It may be because the gear is not actually in place, or because the vehicle handbrake is not put on, or it may be because the synchronizer of the gear in the transmission pants signal is stuck, first check whether the gear is in place, if there is no problem with the operation, you can go to overhaul it.

The problem that the vehicle will not walk in reverse gear is caused by the driver's usual bad car habits, as well as the usual maintenance is not in place.

Workaround:

The first task is to check whether the lower gear is in place, many vehicles need to press or pull to hang into the reverse gear in order to avoid mistakenly hanging the reverse gear, if it can't be hung in, it is necessary to detect whether there is a foreign object in the gear groove that hinders the gear into the gear.

Handling errors are the first task to rule out the wheel, and then consider whether the vehicle has a faulty problem. The problem may be due to a leak in the reverse oil circuit, or a failure of the reverse and high-end clutches, or a fault with the brakes. In the case of hanging reverse gear, it is necessary to pay attention to the vehicle after parking in reverse gear, otherwise it is very easy to cause the problem of shaking and vibration of the vehicle after hanging reverse gear.

1. It is not in gear, and it is still in neutral mode; There is generally no synchronizer in reverse gear, although most of the degree gear can be meshed through the chamfer angle of the gear, but there will always be a time when the two teeth cannot be hung up, at this time, just lift the clutch and let the input shaft turn to re-align the teeth;

2. The handbrake is not put down, and it is still in the state of manual braking, and the car will not move;

3. The clutch is not loosened, the clutch is still in a state of detachment, and the power is not output.

The new Focus car is in reverse gear and does not go. Manual transmissions are also not available.

The gearbox module is broken and needs to be replaced with a new one!

Hello. Your handbrake is not put [There is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

The reason why the Ford Focus automatic transmission does not stay in gear is caused by the failure of the car's transmission and automatic clutch.

The solution is: if the transmission and automatic clutch of the car are faulty, you need to go to the 4S shop or repair shop of the car in time to overhaul the transmission and automatic clutch of the car to solve the problem that the car cannot hang the gear.

Clutch wiring failure, some manual transmission cars still use wiring to control the clutch, the wiring sheath is easy to break and cause no clutch difficult to hang the gear, such a problem is relatively simple, just replace a wiring directly; The self-locking force of the gear on the clutch side is too large, which makes it difficult to enter and exit the gear, in this case, it is recommended to go to the repair shop to adjust the clutch cable and gear lock;

Summary. Hello, when the Focus automatic transmission model hangs the reverse gear, sometimes there is a reaction, sometimes there is no response, then this situation is generally caused by the failure of the solenoid valve body in the gearbox, this fault performance, this specific determination, you need to use the computer to read the fault **, the new Focus, the automatic gear hanging reverse gear suddenly did not respond, and it will be good after a while! What is the reason?

Focus automatic transmission, when hanging reverse gear, there is no reason.

Dear, this question is up to me, it takes a little time to type, please be patient, thank you!

Hello, when the Focus automatic transmission model hangs the reverse gear, sometimes there is a reaction to the nuclear Lingsong, sometimes there is no response, Wang Qin's situation is generally changed Zheng is caused by the failure of the solenoid valve body in the gearbox, this fault performance, this specific determination, you need to use the computer to read the fault **, the repairman said that there is a problem with the computer board, with a change of gearbox and a change of battery boss to a total of more than three thousand yuan, a little bit of a friendship in the heart, so ask the master if he is right?

Transmission oil ha.

Well, that's right, it's the gearbox control module that has a problem, a common problem with this car.

Okay, thank you. Is it better to replace the computer board with a new one or second-hand?

If the vehicle is still going to be driven for a few years, it is best to replace it with a new one, because the second-hand one is not necessarily reliable, and it has been repaired after the problem, please give me advice.

Thank you. You're welcome, and I wish you a great day.