-
Anonymous users2024-02-08Hehe, let's go upgrade first and make do with it. 1.Turn off the power of the set-top box when the TV is receiving the signal from the set-top box, and turn off the signal cable connected to the antenna.
2.Turn on the power supply of the set-top box.
3.Press the "Menu" button on the remote control (the TV displays the "Main Menu").
4.Select "System Settings" and press "Confirm" (the TV display asks for a password).
5.Enter the password "9999" and press "Confirm".
6.Select "Factory Reset" and press "Confirm".
7.Connect the signal cable connected to the antenna (the TV shows the signal strength and quality, both green).
9.Press the volume up key ">" to change "< 1 >" to "< 2 >".
Satellite TV installation.
Changsha satellite TV installation.
-
Anonymous users2024-02-07Zhongxing6 is usual,Zhongxing9Upgrade may not be successful,Even if it succeeds, it will not last long,Radio and television will also be upgraded,If you use an encryption card,Basically, it can't be upgraded,You buy the next version of the machine or turn the star。
-
Anonymous users2024-02-06Your machine is a black machine in the middle of the nine,At that time, it could be used by radio and television and manufacturers in order to fool Lao Baixin's money,After they cheated the money, they adjusted it to make the cable TV of radio and television easy to collect money,It is recommended that you don't do any upgrades,After a lot of upgrades, I watched it for two days and there were only 12 units,If you upgrade him and adjust,Adjust、Adjust again、、、 what do you do。 So I suggest you choose other satellites, if you don't understand, you can take a look at my blog first.
-
Anonymous users2024-02-05The proposal to change stars, or wait and see, is now in constant upgrades, and it has not yet been fixed in the end.
-
Anonymous users2024-02-04Zhongxing 9b upgrade steps:
1. Open the TV and set-top box, and enter the main interface of the set-top box.
2. Use the remote control of the set-top box to operate, find the system setting option, and press the confirm button to enter.
3. After entering, find System Update and press the confirm button to enter.
4. After entering, select Check Update, press the confirm button, and you can start the network to check whether the set-top box currently has an available upgrade package, if so, it will prompt the user to eliminate the code or not**, select Yes, you can start**.
6. After the upgrade is completed, the set-top box will automatically restart, and after the restart, you can enter the new version of the system and start to use it normally.
-
Anonymous users2024-02-03I saw it too, but I didn't try it. In my opinion, set-top box upgrades, just like flashing a mobile phone, require the latest program software. Upgrading is to update the corresponding program software.
I also personally understand, I hope it will help you, I don't know if it's feasible, good luck!
-
Anonymous users2024-02-02Steps:
1.To figure out the box chip combination, you need to unpack the box.
2.Prepare to upgrade the small board and multimeter (judgment and interface pin definition: Rx and TX on the left and right, VCC on the left and right, and GND on the left and right and 0V above 10V, that is, the ground wire).
3.Find the same bin file as the new film combination on the Internet (at least it should be able to support ultra-dense upgrades after February 10) and the corresponding flashing software.
4.Connect the box and the upgrade board, specifically: rx-tx tx-rx gnd-gnd (remember not to connect these three directly to the vcc, otherwise the upgrade board will be burned out).
5.After connecting, turn on the power of the box and the flashing software, and the box LCD will not display at this time.
6.After the software shows readiness, point reset and read, and back up the bin that is left alone (very important).
7.Find the bin file from the bottom of the network and flash it.
8.After 100% of the flashing of Western European hints, turn off the software and the box power.
9.Turn the box back on, and there is a display OK
-
Anonymous users2024-02-01This hate is simple, just read the manual.
Next a new PID code on the Internet, just change it for each channel;
Check the lines and interfaces. The interface was redone, and the strength was stabilized and then adjusted. Connect the cord and find: >>>More
First of all: the upstairs guys are very irresponsible!
That's the case,Disclaimer,99% of copycat machines can be upgraded,The principle is to find out the chip combination of your copycat machine,Write the genuine bin file into the chip,Replace the original bin file that has not been upgraded,So that you can receive the genuine machine46+4 units; The principle is actually the same as swiping your phone! >>>More
Hello: There are many ways to quickly level up Aura Star, it depends on what attribute Abi you are training. >>>More
No. 7 is a boy As for the typo, I personally think that the setting of the early and late stages has changed, that is to say, when No. 7 and No. 8 first appeared, the setting was sisters, but later it was changed to sister and brother, and it is estimated that it is to respond to the July and August, and there are many cases where the setting of stealing stars has changed, for example, the nightingale has white pupils at the beginning of the appearance, but it has become golden in the later stage, and for example, Dr. Amy was obviously a short-haired man in his memories at the beginning, and he was also changed to a yellow-haired girl in the later stage.