The wiper of the vehicle always rings when it is used, does it have to be replaced?

The car has already entered our thousands of households, it can not only ensure the normal travel of families in bad weather conditions, but also the best choice for us to travel short distances. However, it is inevitable that some driving problems will be encountered in the process of driving, which requires the driver to know more about how to deal with common problems. Today we will share the precautions when using the wiper.

The reason for the sound of the wiper can be understood that many car owners have the trouble of abnormal wiper noise, especially in winter and summer, when facing bad weather, the wiper on the car often makes various noises, and the washing effect of the front glass is not ideal. The main reason for the sound of the wiper is the aging of the wiper or the wrong angle of the wiper. In the face of aging wipers, car owners need to replace the wipers in time, and the service life of the wipers is closely related to its materials and manufacturing processes.

The most reasonable solution to the noisy sound is to go to a professional repair shop for professional repairs, and the abnormal noise caused by the wrong angle of the wiper is not. The angle of the wiper arm needs to be adjusted until the wiper blades have a vertical windshield plane. In addition, it is necessary to ensure that the rubber wiper blade can maintain sufficient moisture, and only when the moisture level reaches the standard can it have good toughness to maintain the tightness of the window when it comes into contact with the glass.

The basic requirements when driving a car are to check the condition of the vehicle before using the car, and there can be no potential safety hazards, and secondly, you need to fasten your seat belt to reduce the safety risk. For the safety of your life and the safety of others, do not drive while fatigued, and do not play with electronic devices such as mobile phones while driving, so as not to cause traffic accidents due to inability to concentrate. Drunk driving should be abandoned, and when driving a car, remember not to drink while driving, and not to drink and drive.

Weather conditions are also one of the important factors to consider when traveling by car, and you need to pay attention to road conditions in real time. On the premise of safe driving, you should also actively follow the traffic rules and be a law-abiding citizen.

No. Because the wiper of the vehicle always rings when it is used, it is caused by too much friction, as long as you apply some soap, you don't have to replace it with a new one.

There are two reasons why the wiper should be unresponsive:1The sound of the motor under the wiper may be a faulty motor.

This needs to be overhauled by a professional. 2.The reason for the wiper itself.

Especially in cold winter weather, the aging, wear, and stiffness of the leather strip on the wiper may cause abnormal wiper noise. Hands-on friends can buy online for replacement, and can also buy gauze to polish the leather strip to solve the problem of abnormal noise.

Wiper strips are consumable parts, and if they are used for too long, the strips of the wipers will slowly deteriorate and the blades of the strips will become rough. In addition, the owner usually does not pay attention to the cleaning and maintenance of the rubber strip, and there will be abnormal noises during use. Therefore, please maintain or replace the wiper blade regularly according to the maintenance manual to improve the driving experience and driving safety.

1. Wiper blade aging: wiper blade is a rubber product, it will be aged and hardened after a period of time, and it is more significant in winter. Most wiper blades are recommended to be replaced every one to two years.

2. There is a foreign object in the middle of the wiper blade: when the wiper is opened, there will be a sharp sound of friction between the wiper blade and the front windshield, which can detect and remove the foreign object under the wiper blade or wiper to ensure that the position of the wiper blade is clean.

3. The installation angle of the wiper arm is wrong: it will affect the wiper blade jumping on the windshield, then it will cause a sound. If the wiper blades are normal, you need to adjust the angle of the wiper arm so that the wiper blades are perpendicular to the windshield plane.

There is a sound when encountering scraping glass, and there are three situations.

1. The normal new wiper run-in sound, can be brushed clean, and the sound is not sharp (normal situation) The wiper edge of the boneless wiper is not the same as the bone-based wiper. 90% of boneless wipers are covered with horizontal double or more layers of adhesive strips. Therefore, after the first layer of the new boneless wiper has been drained of all the rainwater, the next few layers of knife edge and glass are dryly scraped, which causes the sound (but the scraping is clean!).

In such a situation, don't worry too much. With a period of use, the sound disappears.

And when the sound disappears and appears again, it is time to change the wiper (or adhesive strip), at this time it is not the sound of dry scraping, but the sound of shaking (scraping is not clean), carefully distinguish the difference!

Second, the wiper knife edge cutting position is wrong, may be accompanied by a process in the back and forth brush is not clean, the sound is sharp (abnormal situation) one is a new boneless situation, one is used for a period of time but the wiper has not yet reached the aging period There is a similar situation! In fact, this situation is due to the deviation of the angle of the wiper rocker arm, resulting in an angle between the adhesive strip and the center of the glass after the wiper is installed (the bone-based wiper is not designed as a whole, and it can be adjusted by itself when encountering such an angle, while the boneless wiper is not!).The workaround is simple:

Use a vise to clamp the U-shaped interface with an iron hook, and then try to slowly exert force clockwise (sound and water marks appear when scraping back) or counterclockwise (sound and water marks appear on the positive scraping), rotate it, generally not too hard, do not rotate too much, just turn slightly!When the hook is reset, don't be careful, don't break the glass when the hook is reset!This will generally solve the problem!

Third, the wiper knife edge problem, aging or defective products, the sound is sharp and trembling, back and forth can not be scraped clean (abnormal situation) generally used for a long time, after the wiper strip is oxidized, 30% of the situation will be similar!However, if the new wiper has such a situation, it must be a wiper problem, and you need to return it to help you replace the wiper.

1. First find out what kind of wiper type your car uses, you can refer to the car manual to see the wiper model indicated on it.

2. Pay attention to whether the way the struts are connected to the wiper rocker arm matches. Some of the arms are screwed to the rocker arm, while others are locked with a buckle.

3. Pull up the wiper and touch it with your fingers on the cleaned rubber wiper to check whether there is any damage and the elasticity of the rubber blades. If the blades are aged, hardened, and cracked, the wiper is unqualified.

4. During the test, place the wiper switch at various speed positions to check whether the wiper maintains a certain speed at different speeds. Especially in the intermittent working state, it is also necessary to pay attention to whether the wiper maintains a certain speed when it is in motion.

5. Check the wiping status and whether the wiper rod has uneven swing or missing scraping. If the following three conditions occur, this wiper is not qualified. First, the swing is not smooth, and the wiper is not beating normally;The second is that the contact surface of the rubber and the glass surface can not be completely fitted, resulting in wiping residue;Third, after wiping, the glass surface presents a water film state, and fine stripes, fog and linear residues are produced on the glass.

6. During the test, attention should be paid to whether the motor has abnormal noise, especially when the wiper motor "buzzes" and does not rotate. This indicates that the mechanical transmission part of the wiper is rusted or stuck, and the wiper switch should be turned off immediately to prevent the motor from being burned.

7. Some people think that the longer the length of the wiper blade, the larger the area of the brush, and the better the field of vision. In fact, wiper blades are not always better. Although lengthening the length of the wiper blades can increase the visible range, it will also increase the burden on the wiper motor and wiper lever.

Of course, it is possible to lengthen it, but it must be guaranteed that it must not interfere with the normal operation of the wipers.

The angle is wrong, just break it.

There are several causes and solutions for the abnormal sound of wiper shaking. I look forward to helping your life, not necessarily complete, but it is also my personal experience, please correct.

1. Some people have such an experience: when driving with a wiper, they find that the wiper shakes badly. Many people are puzzled.

According to this situation, there is a possibility that the wiper swing arm and the rocker arm shaft are not fixed well or the fixed position is improper, resulting in poor contact between the wiper blades and the windshield, and the angle is wrong, resulting in abnormal noise. This can be solved by adjusting the position of the swing arm and installing the wiper blades in place. So it is important to install it correctly and check whether the connection between the wiper and the wiper arm fits firmly.

2. It is also possible that the swing arm is not completely parallel to the windshield. You can remove the wiper first, then attach the wiper bracket to the glass, check if the wiper bracket is completely parallel to the glass, if it is not flat, you can adjust the wiper blade with hand or wire cutter until it is parallel, and finally install the wiper. 3. Also check whether the glass surface is too dirty and has foreign objects.

At this time, glass water comes in handy, properly apply glass water to the glass and clean it with a rag.

4. It is recommended that you can also try to adjust the wiper swing arm. Because the wiper swing arm is not parallel to the windshield, the abnormal sound can also be used to pry the wiper swing arm with a change cone or other tools, and adjust it until the plane of the wiper swing arm is in complete contact with the windshield, and the sound can be eliminated.

5. If the wiper blade is in contact with the windshield too tightly, it may also cause abnormal noise, and the angle of the wiper arm must be adjusted. Finally, remind everyone that the sound of the wiper is generally caused by the aging of the rubber strip, the foreign matter on the glass surface, and the poor stability of the wiper.

Hello, let me tell you a situation, this is caused by the dirty surface of your car glass, you can refer to it.

Generally, the glass is not clean, and there is an atmospheric oil film and the like. It's useless to change the wipers, it's a waste of money, go to TB to collect the aotebas wiper and clean it.

Hello! Glad for your question.

1. Wiper blade aging: two wiper blades are rubber products, which will be aged and hardened after a period of time, and it is more significant in winter. Most wiper blades are recommended to be replaced every one to two years.

2. There is a foreign object in the middle of the wiper blade: when the wiper is bent, there will be a sharp sound of friction between the wiper blade and the front windshield, and the car owner can detect and remove the foreign object on the wiper blade or the bottom of the two scrapers to ensure that the position of the two wiper blades is clean.

3. The installation angle of the two wiper arms is wrong: it will affect the wiper blades to jump on the windshield, then it will cause a sound. If the two wiper blades are normal, you need to adjust the angle of the wiper arm, and the two wiper blades should be buried directly at the windshield level.

1.If it rings when going up, then it means that the wiper holder is twisted upward, let the wiper stop in the middle position (pull the wiper control handle towards the steering wheel after the car is turned off), and then gently pull it up, wrap the steel frame with a cloth or soft thing, use a wrench or pliers to grip the wrapped part and twist it downward, scrape it after resetting, is the abnormal sound a little smaller? If so, repeat once until the squeak is eliminated.

If it starts to ring when it becomes downward, it means that the wrench has been overturned and needs to be wrenched in the opposite direction. Until the squeak is eliminated!

2.If it rings when going down, then it means that the wiper holder is twisted downward, let the wiper stop in the middle position and pull it up, wrap the steel frame with a cloth or soft thing, use a wrench or pliers to clamp the wrapped part and twist it upwards a few times, scrape and try after resetting, is the abnormal noise a little smaller? If so, repeat once until the squeak is eliminated.

If it starts to ring when it becomes up, it means that the wrench has been twisted too much and needs to be twisted in the opposite direction. Until the squeak is eliminated!

3.Careful and patient operation is required. It is best not to be afraid of trouble, and operate the boneless wiper after removing it.

If you don't have any experience in this area, you should go to the 4S store and let them adjust according to this principle, which will generally solve the problem.

4. If a single wiper blade has an abnormal sound when going up and down, then it is really time to change the wiper blade.

The way to deal with the wiper scraping sound, let the wiper stop in the middle position, gently pull it up with your hand, then wrap the steel frame with a cloth or soft object, and use a wrench or pliers to clamp the wrapped part and twist it down a few times until the abnormal sound is eliminated.

After many car owners buy a car, the wipers may not be replaced frequently, so in the case of long-term exposure to the sun or rain and wind, there may be some aging phenomena, or some deformation, etc. A phenomenon like this may also cause some foreign objects in the windshield, so in this case, many people also consider whether to change the wiper blade.

In fact, you can first check whether there are some other foreign objects between the wiper strip and the windshield, and if there are some other foreign objects, it is likely to cause some shape deformation of the wiper and so on. The other is to raise the wipers, as for such a maintenance position, you can check which parts of the wiper strip have some hardening, or some burr notches and so on.

If the wiper blade looks very old or does it crack, it can be replaced in time. In addition, many people will also find that some windshields may also have some oil films, and oil films like this may also make the wipers age. In addition, such a windshield can be tested in the rain, some people may feel in the process of daily driving, that the vision looks very unclear, thinking that the wipers are not clean.

The line of sight looks very unclear, but in fact, it is not, and in some cases, it may be because the windshield is drenched in water for a long time or some of the oil film is spent in the process of long-term use. Therefore, in this case, it is necessary to clean the windshield accordingly to make the whole glass look clearer. In addition, in the process of using this water test, we will see if the water on the windshield will disperse quickly.

If it spreads out quickly, it means that there is still an oil film on the glass, which can cause some shaking or abnormal noise of the wiper blades.