What to do if the freezer compartment of the refrigerator is always frozen

If the temperature of the refrigerator is set too low, the melted water will freeze if it cannot be discharged when the refrigerator is shut down normally.

This is a common phenomenon, there is a drainage hole in the back wall of the refrigerator room, and the melted water can be discharged from here during normal shutdown, and it is blocked by a small amount of debris (or slightly) after a long time, resulting in the water cannot be discharged out of the box, and the fresh-keeping layer will accumulate water (or freeze). You can open the small lid behind the refrigerator and you can see the drain head, and blow the pipe (or blow with a gas pump) to blow out the debris! Then pour some water from the drain hole in the refrigerator (add a small amount of washing) and rinse it a few times!

Very effective! There will be no stagnant water.

1) Cause analysis.

1. There is too much frost on the evaporator, and the water overflows the water tray when it melts and flows in the refrigerator.

2. The water tray in the refrigerator is not aligned with the water receiving funnel, resulting in the water flowing in the refrigerator.

3. The drain pipe mouth is frozen, so that the defrosting water cannot flow out, and the flow accumulates in the refrigerator.

4. Cold drinking water or other beverage containers are turned over and flowed in the refrigerator, or the lid of the beverage bottle is not tightened and is placed horizontally on the food shelf, causing the beverage to flow out.

5. Usually, the refrigerator door is not closed tightly, or the sealing strip is damaged, so that the outside hot air continues to flow in and condense into water.

6. There are too many lukewarm foods stored in the refrigerator, such as hot drinks, hot tofu, mung bean soup, etc., which instantly form a large mist and water droplets in the refrigerator, which condense into water as the temperature drops.

7. The water content of the food stored in the refrigerator is large, and with the drop of temperature, the water vapor in the food evaporates, and then condenses when it is cold, and then becomes water, which flows in the refrigerator.

8. The temperature in the refrigerator is too low, causing the glass bottles of soda, beer, fruit juice and other beverages to burst, and the liquid flow box.

9. In summer, the hot air enters the refrigerator from the outlet pipe, resulting in an increase in water vapor in the refrigerator.

10. When the water in the freezer is too full, and the water freezes into ice, the water overflows the ice maker and flows in the refrigerator due to the expansion of the volume.

11. The antifreeze device of the refrigerator is damaged, and in the rainy season, the hot air condenses dew on the outer surface around the refrigerator door and flows on the ground.

Due to the influence of the above factors, when there is too much water in the refrigerator, it will flow out from the bottom edge of the refrigerator.

2) Exclusion method.

1. When using refrigerators, it is necessary to defrost frequently, which is also a measure to save electricity.

2. Adjust the water receiving funnel and align it with the position of the receiving tray.

3. The temperature in the refrigerator should not be adjusted below 0 °C, usually 2-6 °C is appropriate, so as to prevent the water from freezing.

4. When refrigerating beverages, they should be handled gently, and the plastic container with the bottle cap should be placed on the food shelf of the door leaf, and if it is placed on the food shelf, the bottle cap should be tightened to prevent the liquid from flowing out.

5. When using the refrigerator, it is an important task to open and close the door tightly, and it is necessary to be careful to prevent cold; If the sealing strip is found to be damaged, it should be repaired in time; It is also required to pay attention to whether there is dirt on the door edge and adhesive strip at all times, and if found, wipe it off immediately.

6. Hot food is not allowed to be put in the refrigerator, and it is necessary to wait for it to cool to room temperature before putting it in the refrigerator.

7. For food with a lot of moisture, it should be packed in a plastic bag, and the mouth of the bag should be tightened to prevent the evaporation of water vapor in the food and increase the amount of water in the refrigerator.

8. The temperature of the refrigerator in the refrigerator should not be lower than 0 °C, and should be controlled at 2-6 °C, so that the bottled drink will not burst.

9. In summer, put some water in the water container outside the refrigerator, and then connect a section of rubber pipe on the head of the outlet pipe in the refrigerator, and immerse the other end of the rubber tube in the water, so as to prevent the outside hot air from entering the refrigerator from condensing and dripping. 10. When freezing ice cubes or popsicles, the water in the ice maker should not be too full, and it is generally better to add 80% of the capacity.

11. Carry out maintenance.

The temperature of the refrigerator is too low. The refrigerator compartment is used to keep food fresh, and the normal temperature is usually between 3 degrees and 8 degrees. If the temperature in the refrigerator compartment is too low, the glass bottles or cans in the refrigerator will burst, and the liquid will flow into the box and it will be easy to freeze.

Therefore, when using the refrigerator, pay attention to adjusting the temperature of the refrigerator compartment to a suitable temperature range.

The refrigerator door seal is not tight. The refrigerator door has a sealing strip on it, which is designed to ensure that the hot air outside the refrigerator does not enter the refrigerator and ensure that the temperature inside the refrigerator is constant. If the seal on the refrigerator door is not tight, the hot air from the outside of the refrigerator will flow into the refrigerator, and when the refrigerator is cold, the hot air will condense into water, which will cause the refrigerator compartment to freeze.

Therefore, if the refrigerator room freezes, pay attention to check the refrigerator seal to see if it is caused by its looseness.

The thermostat is faulty. The thermostat is the key to controlling the temperature of the refrigerator compartment, if the thermostat itself is faulty, the compressor will not work for a long time. This causes the temperature in the refrigerator compartment to continue to drop, which in turn leads to the freezing of the refrigerator.

Food is close to the back liner. When the refrigerator refrigerator is refrigerated, the back wall is frosted, and the food is placed too close to the back wall of the refrigerator, and the food is placed too close to the inner tank of the back, because there is a refrigeration line in the back, which will cause freezing. At this time, just unplug the refrigerator and clean up the ice water when the ice cubes have dissolved.

Freezing in the refrigerator may be due to the temperature being set too low, and then the sewer pipe in the refrigerator freezes and the stored water freezes.

There are many reasons for freezing in the refrigerator room, specifically the following points: 1. The temperature of the refrigerator is too low, and the temperature of the refrigerator should be set between 4-8 degrees. If the thermostat is mechanical, the gear should be adjusted reasonably according to the temperature of the season, the gear should be adjusted to 1-2 gear in summer, 3 gear in spring and autumn, and 4-5 gear in winter, keep the temperature of the freezer at about minus 18 degrees, and the temperature of the refrigerator between 0-10 degrees, preferably between 6-8 degrees.

2. The door seal is not tightly sealed or the door is opened frequently or the door is opened for too long, resulting in serious loss of cold air in the refrigerated room. If the seal is not tightly sealed, the new door seal should be repaired or replaced in time, and the number or time of opening the door should be minimized. 3. The thermostat itself is faulty, resulting in the compressor working for a long time without stopping.

If it is a mechanical thermostat, there are three reasons: 1. If the thermostat is loosening and displaced, the loose thermostat should be restored to its original position and fixed, so that it can be in close contact with the evaporator in the back wall of the refrigerator; 2. The internal contacts of the thermostat are sticky, and the emergency treatment method is: first cut off the power supply of the refrigerator, rotate the thermostat knob to 0 gear, and then rotate to the highest gear, so that the contacts can be separated by rotating a few more times, and then adjust the gear to 1-2 gears, and then turn on the power supply test machine after 5 minutes of power failure, if the compressor can be shut down, it is troubleshooting.

3. If the thermostat temperature sensor tube is damaged and leaked, the thermostat should be replaced with a new one, and the general electronic market refrigeration component store is about 25 yuan. In case of emergency, you can also buy an external refrigerator bosom friend (about 10 yuan), that is, the refrigerator compressor start-stop time controller, and set the start-stop time of the compressor according to the seasonal temperature, but it needs to be adjusted frequently and is not suitable for long-term use. Generally, the working time of the compressor can be set between 10-30 minutes, and the downtime of the compressor is adjusted according to the temperature of the season

between 1 and 1:2; It is around 1:3 in spring and autumn, and 1:3 in winter

Between 5 and 1:10, it is fine to keep the temperature inside the refrigerator within the normal range. When the compressor is working, frosting on the back wall of the refrigeration room is a normal phenomenon, because the back wall of the refrigeration room is an evaporator, and when the compressor is working, the temperature of the evaporator is very low, which cools down the refrigeration of the refrigeration room, so it is normal for frosting to occur.

You should check whether the compressor is working properly, if the compressor does not stop working for a long time, it is either caused by the refrigerator temperature being adjusted too low, or the thermostat is faulty.

1.We can buy defroster and put it in the fridge.

2.With the power of the refrigerator cut off, take out the food from the refrigerator and put a basin of hot water in the refrigerator.

3.Close the refrigerator door in the refrigerator room and wait about 10-15 minutes. The temperature of the hot water will cause the ice in the refrigerator to melt very quickly, and the water will flow out of the refrigerator.

The reason why the refrigerator is thick and cold:

1.There is a small hole at the bottom of the refrigerator that is the exit of the refrigerator. If it is not cleaned for a long time, a thick layer of limescale will accumulate in the outlet. When the scale is too thick, it will directly affect the drainage of the refrigerator, resulting in the problem of freezing in the refrigerator.

2.The refrigerator should be placed more than 10 cm from the wall. If the refrigerator is placed too close to the wall, it will affect the heat dissipation of the refrigerator, and the excessive temperature difference between the inside and outside will also cause such a problem.

3.The door of the refrigerator will close, which will also cause ice to build up inside. Refrigerator seals can also have the problem of insufficient adhesion after being used for a period of time. Once the seal is aged, we also need to replace it in time to avoid affecting the normal service life of the refrigerator.

The temperature of the refrigerator should not be set below 0°C, generally 1-5°C, to prevent the water from turning into ice. Then check that the gasket on the door is well sealed. You can cut a piece of paper and put it between the door and the refrigerator to see if it will get stuck, and the position that cannot be clamped indicates that the seal is poor.

It is also possible to add sponge strips on the inside of the door seal to strengthen the withered seal.

There are many reasons why ice can form in the fridge:

1. There is too much frost in the evaporator. The frost turns into water, which then flows through the drip tray and into the refrigerator.

2. The water bowl in the refrigerator is not aligned with the funnel, causing the water to flow into the refrigerator.

3. Freezing of the drain prevents condensation from flowing out, but it will accumulate in the refrigerator.

4. The bottle with water without tightening the cap was placed horizontally in the refrigerator, and the water in the bottle was spilled directly on the glass plate and left in the refrigerator.

5. If the refrigerator door is not closed tightly, the sealing tape may be damaged, and the hot air will flow in from the outside and condense into ice.

6. There are too many warm foods in the refrigerator, such as hot drinks, hot tofu or mung bean soup, etc., which will immediately produce a large amount of mist and water droplets in the refrigerator, which will condense into water and drop in temperature.

7. The food in the refrigerator has too much moisture. When the temperature drops, the water vapor in the food evaporates. When it's cold, it condenses and then turns into water and goes into the refrigerator.

8. The temperature in the refrigerator is too low, causing glass bottles of soda, beer, juice and other beverages to rush into the liquid flow box.

9. The temperature is high in summer, and the hot air enters the refrigerator from the air outlet pipe, which increases the humidity in the refrigerator.

10. The fridge is too full of water. If the water freezes, the water will flow over the ice maker into the refrigerator due to its volumetric expansion.

There may be a deviation in the water receiving funnel, so that the water receiving funnel of the refrigerator needs to be adjusted, so that the receiving water funnel can be aligned with the position of the receiving tray, and then the excess water will flow into the receiving tray accurately. If the temperature of the refrigerator compartment is too low, then it is necessary to carry out relevant adjustments, do not always adjust it below 0 degrees, but need to adjust the refrigerator to 2 6, so that the storage of more high-quality leakage blind items, but also to prevent the refrigerator from freezing.

If the refrigerator freezer room is always frozen, then it needs to be treated, first of all, defrosting should be done in the solution process, which is also a measure to protect the refrigerator. You can take out the refrigerator of the refrigerator, then clean the frozen ice inside, and at the same time the refrigerator is powered off, wipe the inside and outside of the refrigerator clean, and then use. During use, the empty refrigerator can be run first, and no items can be placed in it, and then loaded when the refrigeration link meets the qualified requirements.

During the daily maintenance of the refrigerator, it is necessary to wash and ventilate frequently, so that the items can be stored in the refrigerator better, and the actual benefits of the refrigerator will be greater.

There are generally a few freezers in the refrigerator:

1. The gear adjustment of the refrigerator room thermostat is not suitable, and the larger the number of the thermostat, the lower the temperature.

2. The food in the refrigeration room is placed at the back, close to the inner tank of the back, because the current condenser is on both sides, and the refrigeration pipeline in the back will cause freezing.

3. That is, the thermostat is abnormal, and it cannot accurately sense the change in the temperature of the melon cover for the ingot stack.

4. The more serious thing is that the refrigeration pipeline on the back is too close to the gold liner, which causes freezing.

Note: You can solve it at home, and you need to contact the maintenance department to ask professional personnel to deal with it.

1. The air humidity in the refrigerator or freezer room is high, and the temperature of the evaporator in the refrigerator is low, which leads to the problem of freezing in the refrigerator. 2. There is water vapor in the air outside the refrigerator, when the refrigerator door is opened, the new air will bring a part of the water vapor into the refrigerator, and the temperature of the evaporator in the refrigerator is very low, and the water vapor will condense into frost after entering the refrigerator, resulting in the problem that the refrigerator room is always freezing. Qiaoyuan Suggested treatment method:

1. Use hot water de-icing method. What is the reason for the problem of reducing the freezer in the refrigerator and the freezer room is always freezing. To operate, you should turn off the refrigerator switch, then put two bowls of hot water in the refrigerator, and at the same time close the refrigerator door and let it stand for 15 minutes.

After 15 minutes, open the refrigerator door again, so that the problem of the refrigerator becoming thicker is solved.

2. Fan defrosting method for lidani liquid. Open the refrigerator and freezer doors, turn on the switch of the electric mold wide fan, blow at the refrigerator, and wait for a while for the ice on the refrigerator to dissolve.

3. How to increase the temperature of the refrigerator itself. Turn up the temperature of the refrigerator itself and wait quietly for 2 to 3 hours so that the ice in the refrigerator will melt naturally. The refrigerator is very thick and the problem is solved.