Konka E5838 how to connect to the wireless network of the notebook

You put the signal out and you're ready to connect. I use the conn software. It's been cracked now, and it's good to use.

Dear users:

Hello! Thank you for your support of Konka products! The wireless stool of the TV needs a wireless network card and a wireless router for networking, but the TV has requirements for the rough chip model of the wireless network card, and the chip models that can support the wireless network card are RTL8191SU, RTL3070, and RTL8712.

There is no need to install a wireless network, the TV has purchased a wireless network, turn on the wireless function, and the connection can be:

1. Use the TV remote control to open the settings.

2. Select network or wireless or wifi. The TV models are not the same, the versions are not the same, there are slight differences.

3. Then select the wifi you want to connect to, enter the password to connect. The process is basically similar to that of a mobile phone.

If the manual can be connected to a wireless network,There should be a built-in network card inside the TV,You don't have to buy it again;

I helped you check the parameter list of this TV,It says that there is a network interface。

Dear users:

Hello, sorry for the inconvenience caused by the production of regret products!

According to your feedback, it may be a problem with the wireless router settings, 6100 series TVs, built-in wifi function, the wireless router settings that our TVs can recognize are:

Using the WEP encryption method, the settings are as follows: open for authentication mode, 64bit for wep encryption, ASCII for key mode, any one key can be set, and the password needs to be set to 5 digits. The WPA encryption method is used for selling, and the settings are as follows:

Set the password type to TKIP, select psk for PSK EAP, and set 8 digits for the password. Passwords are recommended to be purely numeric.

Please refer to Resetting the Router;

TV manual regret Li has this one to check the steps before the operation,This to buy a VGA cable to connect the computer and the TV,For detailed steps, you can search for TV connection to the computer The first webpage is introduced。

If you don't buy a cable,You can also directly use the electric eggplant as a computer,Plug the network cable into the port behind the TV,The TV can be set up again to access the Internet。

Dear users:

Hello, sorry for the inconvenience! It is recommended to use a VGA cable to connect the TV and the notebook, first adjust the screen resolution of the notebook to 1024*768, adjust the refresh rate to 60 Hz, use the VGA cable to connect the TV and the notebook, and then turn on the TV first, select the TV signal source to the VGA computer status confirmation, and then turn on the computer. If only the notebook is displayed, and the TV is not displayed, it is recommended to adjust the output mode of the following notebook, and the specific method can be consulted by the computer after-sales service.

1. Open Settings - Network Settings - Wireless Settings - Find WiFi at Home - Connect - Enter Password - OK!

2. If you don't have built-in wifi: spend 50 yuan to buy a universal wifi receiver.

Plug the universal wifi receiver into the computer first--take out the driver disk of the universal wifi receiver and install the driver--plug it into the TV after success--repeat step 1! --ok

No, you're sorry for me: 1. I'm professional.

2. I am pure hand-played.

3. I really want to help you.

You need to have a wireless router at home, and a TV needs to have wifi or a wireless network card that can be plugged in.

2. After entering the router settings page, turn on the wireless function, and set the wireless network login username and password.

3、Turn on the TV and find the wifi or wireless network card according to the instruction manual and open its login interface,Enter the user name and password set in the router into the corresponding position,Then click connect or OK。 It's best to set it up here to automatically log in later.

Dear users:

Hello, thank you for your support to Konka. If your home TV needs wired networking, you need to use a router and network cable connection, if your home TV needs wireless networking, you need to use a wireless router and wireless network card at home, such as the TV has built-in wireless wifi, no need to be equipped with a wireless network card.

It's just that all the wires are unplugged, and it's wireless.

Seems to need a router.

Generally, TVs do not recognize advanced encryption methods, so try to change to web authentication.

It should be that the password was entered incorrectly. I also just bought the R6100 on the National Day, my WPA2 encrypted wireless, at first the password was entered incorrectly, and it couldn't be connected, and then re-entered, and it was soon fine.

You first make sure that your TV has a wood and wifi function.

Network-Wireless-WiFi is turned on,Search for the wireless router signal,Enter the password,Click to automatically get the IP address to connect,In addition, the TV also has requirements for the setting of the wireless router。 The wireless router settings that the TV can recognize are:Use WEP encryption,The settings are as follows:

The method of recognition and burial of the secret certificate is open, the wep encryption method is 64bit, the key method is ASCII, the secret key key can be set to any one, and the password needs to be set to 5 digits. WPA encryption is used, and the settings are as follows: TKIP is set to password type, PSK ESP is set to PSK, and the password must be set to 8 digits.