Curtain rod fixing problem, what are the fixing methods of curtain rod

There should be a matching mounting mount, ask the store. Take a look below to find out how to install it.

Installation of Roman rods.

The window is the eye of the room, and the curtain is the soul of the window;

The living room is brightened by the windows, and the windows are animated by the curtains.

What you need for installation:

Hammer drill and matching 6mm drill bit, steel tape measure, pencil, cross-shaped driver,

6mm plastic expansion tube, 4 40mm self-tapping.

Installation steps (taking open supports as an example):

1.Get ready. Check the matching of the Roman rod and its decorative heads, bearings, and lifting rings, measure the length of the Roman rod and the width of the window.

2.Lineation. Take the installed support as the standard line, and draw the support positioning line and hole position line.

For 3 supports, the middle support is located in the center of the window or wall, and the ends must be equidistant.

The supports at both ends are about 15-20 cm away from the wall or 5-10 cm away from the ends of the Roman rod.

3.Perforate. The depth of punching is 4——, and you can not run the eye or skew when punching, note: keep away from wires and water pipes. After punching the hole, knock the plastic expansion tube into the hole.

4.Mounting rods.

The bearing is fastened with self-tapping wire; The lifting ring is sleeved into the rod, and the lifting ring is divided into two, leaving 1-2 lifting rings at each end; The Roman rod is pressed into the open support and adjusted so that the distance between the decorative heads and the wall is the same.

5.Hang curtains.

Wear the curtain through the hook and fork the other end of the hook into the hole of the ring; Open and close the curtains left and right, and check whether the sliding is flexible and whether the two curtains are of equal height. Otherwise, fine-tune.

Curtain rod installation essentials.

Level. Housing prices are getting higher and worse quality, especially for some affordable housing and those under construction. I have seen roofs that are tilted by 10 cm, floors that are uneven and tiled by 5 cm, and walls that are trapezoidal. It is best to use a level or a level tube for installation.

Disclaimer: Not special! Please do not sit in the right seat!!

The high roof effect is good.

Since it is necessary to express the beauty of the exposed curtain rod, it is best to have a certain height on the top of the living room and the window, so as not to produce a feeling of compressing the vision.

When installed on the wall (referred to as wall installation), the Roman rod is about 6-12cm away from the roof or ceiling to avoid a feeling of depression and suffocation;

When installed on the roof or ceiling (referred to as roof security), the Roman rod is about 7-10cm away from the wall to prevent the curtain from rubbing against the wall and staining the curtain cloth when it is opened and closed.

Leave room The Roman rod should not be less than 6 cm longer than the window frame, so that the curtain cloth can completely cover the window;

The length of the Roman rod (excluding the decorative heads at the ends) when the curtain cloth covers the entire wall

It is about 18-22cm shorter than the net width of the room, and after installation, there is a gap of about 2cm between the decorative head of the Roman rod and the wall, which is the so-called "place to leave".

When buying curtain rods, the accessories are free to match, and the color and size of the accessories are matched. To you, the steel pipe ** is about 20 per meter with fittings. It is generally side-mounted (on the wall above the window).

If you want to match it well, the size and color are not easy to find, generally not, the curtain rod should have better accessories, but it may be worth the money, you can ask.

Go to the hardware and building materials store to buy a steel pipe support frame, there are 19cm and 25cm and then fix it on the wall.

curtain rods.

The installation method of the open rod and the dark rod is not much different, and it is basically in accordance with the process of assembly, positioning and fixation. Let's take a look at the general process and method of curtain rod installation. 1. The way to hang curtains on the curtain rodThe curtain rod is divided into those with hanging rings and those without hanging rings.

The curtain rod with hanging rings is used to hang the curtains processed by the cloth belt directly, and the finished curtains can be hung directly with four-legged hooks. The curtain rod without hanging ring is mainly used to hang the curtain with perforation or rod processing. Curtain rods with hanging rings need to be assembled before installation.

2. Before determining the installation width and height of the curtain rod, the installation position of the curtain rod should be determined. i.e. installation height and width. The width of the curtain rod can be determined by the width of the window, which is 20-30cm more on both sides than the window width.

The installation height of the curtain rod is different from the bright rod and the dark rod, the installation height of the open rod is in the middle of the ceiling to the top of the window frame, and the dark rod is at the top of the curtain box, or the side is installed in any part of the curtain box. 3. Positioning and punching take into account the firmness of fixing, to avoid the spacing of the fixing parts is too large to withstand the tensile force, it is necessary to calculate the fixed hole distance first, and the separation distance of the general fixing parts is not more than 50cm, and then draw a line for positioning. Once the installation position is set, it is necessary to drill holes and fill in the expansion screws.

If it is a wooden base, there is no need to drill holes, and it can be fixed directly with self-tapping screws. 4. Install the curtain rod For the Roman rod, after the hole is drilled, the mounting frame can be fixed first, and then the rod can be placed on the mounting frame. In the case of curtain rails, the assembled curtain rails are directly fixed to the wall or ceiling with side or top codes.

When the hole is bigger, you can tighten the wooden screws with a wooden plug, which is stronger than the general plastic expansion plug. So simple question! In the case of a hollow insulation wall, a special expansion plug in the shape of an airplane with wings is used.

Stuff some pieces of wood in the holes and fix them, or simply paste them with cement and wait until they are completely dry, and then beat them again.

Kiss! Hello, happy to answer your <>

The use of pro-telescopic curtain rod is as follows: 1. Measure the size, and the distance from the screw must be within the use distance. 2. According to the hole spacing at the end of the bracket, draw a point to drill holes.

3. Fix the bracket on the wall with screws 4. Adjust the tube to the desired distance, the tube can be completely pulled out and hung with curtains. 5. Install the curtain rod on the bracket and screw it. One:

Clarify the structure of the structural telescopic curtain rod including the outer sleeve, the inner sleeve, the spring support and the bracket support. To figure out the installation skills of the telescopic curtain rod, the first thing to be clear is the structure of the telescopic curtain rod, if the structure is not clearly understood, then there will be a lot of jokes when installing the telescopic curtain rod. Two:

Therefore, it is good to check whether the telescopic curtain rod is in good condition when installing the telescopic curtain rod in the early stage, and determine the location that needs to be installed, so as not to be in a hurry during the installation, or find that the product has a problem after the installation, which will waste a lot of manpower and financial resources. Three: installation tips In fact, the installation process of the telescopic curtain rod and the aluminum shutter track is almost the same, and the installation of the telescopic curtain rod is easier and faster than the installation of the aluminum shutter track, and you only need to let the inner casing be sleeved in the outer casing.

Even if you're just a rookie in decoration, you're guaranteed to learn it as soon as you learn it. Four: free adjustment according to the needs because the telescopic curtain rod has a freely adjustable length, the vertical and horizontal position of the telescopic rod can be adjusted by the installation bracket, so it is loved by the majority of consumers, then you must not miss this function, and you must adjust freely according to your actual needs when installing.

Hope mine can help you <>

Do you have any other questions?