Broadband and router conflict, will the two routers conflict?

What a mess of information you've provided. Hope it helps.

Start by setting up your router with broadband disconnected. Only connect the computer to the router LAN and dial all the others.

Open first to find the LAN settings, and you will see Replace it with something else, for example.

The route then prompts you to restart the app, Restart.

Re-open the LAN address is what you just changed).

The rest of the settings follow the normal routing settings, you didn't say anything. That's it. If you don't understand, you can continue to ask.

Yes, some broadband needs some operation to support, I hope you can do what I say and add a color to the New Year.

3: Login. 4: Enter the correct password and password in the Internet access password, the password is the user name, which is displayed in the broadband handling form.

5: Restart the route.

Problems with route relays! Route relay may not be supported!

Switchboard??? Not a router??

If you set it up, you won't.

Wireless router to wireless router, the second router setup, there are two ways (provided that the first router has been set up and can surf the Internet normally):

The first method: dynamic IP mode (the first route is the primary route, and the second route is the slave route).

1. Plug in the router and do not connect the LAN port of the main router first, and reset the slave router (restore the factory);

2. Connect the computer from any LAN port of the router to enter the settings page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the LAN port of the main router to the WAN port from the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router first, and change the IP address of the slave router. For example, most router addresses are, we just need to change from router IP address to that;

2. Turn off the DHCP function from the router in the settings;

3. Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

Sometimes one router is not enough, we will use two or three routers to connect and use together, but sometimes when you connect the second and third routers, the second and third routers cannot be used and cannot work properly, so do you know what to do if the two routers conflict? Here's a list of some information I've compiled about two routers that conflict.

Resolution of a conflict between two routersPress Enter to enter the router login page. Enter the username and password (the router manual has the username and password), and then click OK to enter the router page.

Go to the Router page and select network parameters.

Select LAN port settings from the drop-down list.

Click Save, then the router will restart, and then you have to enter the router settings in the browser to enter the address you just changed.

1.Workarounds for IP address conflicts caused by routers.

2.What should I do if there is a conflict between 2 router IP addresses?

3.How to Solve the Problem of Signal Interference Between Two Wireless Routers4What should I do if multiple router addresses conflict.

1. If the line access conflicts, it is necessary to check the main hall and the slave router, or both are from the router, that is, from the main router;

2. If there is a master router and a slave router, the normal correct connection method is that the WAN port of the main router is connected to the optical modem terminal, and at the same time, it is necessary to ensure that the gateways of the routers connected to the network cable are different;

3. If the network cable of the main router is connected to the LAN port of the main router to surf the Internet, and there is no access to the WAN port, then the DHCP of the main router needs to be closed, and the DHCP of the slave router should also be turned off to avoid gateway conflicts;

4. The gateway setting conflict, the gateway of the master router and the slave router are the same, or the gateway conflict between the slave router and the optical modem, this situation can only be solved by setting the gateway differently one by one, and at the same time, it is necessary to check whether the wiring is wrong. Change pants.