How to load the printing paper in the stability inspection cabinet?

1.Press firmly down on the paper recorder cardboard and the paper deck will automatically pop up.

2.Open the paper recorder paper box lid with the thermal side facing up, load the thermal paper, keep both sides of the thermal paper neatly around the glue stick, and then insert the cardboard.

1.Single-page printing, feeding paper from the front of the printer. 2.Perforated paper prints continuously, feeding from the back of the machine. Jam the hole of the paper on the jam tray at the rear of the printer. See figure.

Stability inspection to print, just better according to the procedures of the printing room to install it.

The printing paper of the text wire examination sentence is packed with a four sheets.

Stability to examine the specific time of his construction, you can do your filial piety by giving you some specific things. And then each of them has different rules, and each one has a different experience.

Stability archaeological expedition expensive printing paper can we also install, or can it bring us all good use and help?

It is very difficult to install the printer model.

How to install the printing strip of the stability inspection cabinet? This should be checked and go to a professional place to find out about this.

The printer paper of the stability inspection cabinet can be installed.

Stability Survey: How to Load Your Printing Paper, How to Install Stability Survey, How to Install Stability Paper, How to Load Printing Paper.

How to load the printing paper in the stability inspection cabinet? The stability is high, the printing paper of the tea cabinet is still very easy to install, and there is a hidden mirror shell under his transfer machine.

It is generally called the paper slot.

When using the host computer to issue samples, the printer does not work. When the printer was turned on and found that there were no foreign objects in it and the temperature was not high, Chachong needed to check whether the internal parts of the printer were damaged or damaged.

1. The paper parts are damaged.

Each part of the paper channel of the printer is equipped with a paper jam check switch or sensor, the printer should check the passing status of the paper regularly when working, if the paper is not sent away in time in a certain part, or the paper roller does not absorb the paper, it will also report the paper jam error, the common reason is that the paper roller is damaged, the paper motor is damaged or the circuit is damaged. This failure can only be repaired or replaced.

2. The paper path sensor is faulty.

The sensor is very important in the paper feeding channel, and if the sensor itself is damaged, contaminated by low-quality toner, dust, or blocked by confetti wheels, the sensor will not work properly, so that the machine will always be in a jammed state. In this case, you should first check whether the paper feed detection sensor and the paper discharge detection sensor are damaged. Shake the paper feeding detection sensor rod to detect whether the voltage of the connector on the circuit board of the DC controller changes between 0 5V, if not, there is a problem with the high-voltage power supply, and the high-voltage power supply circuit board needs to be replaced; If so, proceed to check the DC controller circuit and the paper discharge sensor.

Also, be sure to use a high-quality professional toner.

3. The driving parts are out of order.

Drive clutch, gear and shaft slippage can cause paper transfer to be disrupted, resulting in paper jams. If the electromagnetic clutch does not engage and cannot drive the suction roller to rotate, use a multimeter to measure whether there is voltage at its input terminal to determine whether it is a fault of the clutch itself or a front-end power failure. If the paper roller rotates and does not feed the paper, you need to check whether the paper tray is installed in place, the suction roller is too dirty or there is oil to reduce the friction, and it cannot be fed, and it should be cleaned with a damp cloth or alcohol.

4. Failure of separation parts.

The function of the separating claw is to separate the paper from the surface of the drum, if the separating claw is damaged or the spring of the separating jaw is deformed, etc., the paper can not be separated, resulting in paper jams, which is also one of the common causes of paper jams in printers. Damaged separator jaws can also damage the drum, so it must be cleaned and inspected frequently.

Through the above analysis, we should pay more attention to regularly inspecting all parts of the printer, and do a good job of cleaning, ventilation and paper selection.