Why does the network speed slow down when using 100 Gigabit fiber Internet access?

I think this may be due to insufficient quality or breakage of the fiber.

The main reason is that there are still a lot of people who use it, so it will slow down.

Maybe it's because there are a lot of people who use it, so the network speed will be slow.

Because of a certain network speed, but he will become very slow when the amount of use transitions.

Maybe it's because the population is too large, and then the rate of receiving it is very slow.

Because this one is not very stable, and there are many users who use it at the same time.

There are many reasons why this happens.

I think it's because of some glitches that make the internet speed jump around, so it's not fast.

Because everyone shares this 100 megabit fiber Internet access. Naturally, it's going to be a lot slower.

Because there are more users, it is said that many people will be slower to surf the Internet together.

Here's why:

1. Light modem. First of all, make sure that the modem sent by the operator supports Gigabit, and at the same time, ensure that the network cable leading from the modem to the router is correctly plugged into the interface of the Gigabit network.

2. Router. If the router is a gigabit router, it must also be guaranteed. If the router is connected to a computer, the LAN port should also be plugged into the Gigabit LAN port.

This is not over, go into the router settings to see, whether the gigabit mode is turned on, and the functions such as intelligent speed limit are also turned off, and the speed limit is adjusted to more than 1000m.

3. If the network cable is unqualified, the network speed will also be attenuated. Category 5 cables only support 100 Gigabit networks, while Category 5 and Category 6 network cables can run full gigabit networks, and the type of network cable will be marked on the network cable. If it is not the old Category 5 line, then replace the Category 5 or Category 6 line.

If it has been replaced, it may be that the crystal head is not ready, so try again.

4. Computer settings. Finally, there may be a situation that the mobile phone can be connected to wifi to Gigabit, but the computer is still a 100 Gigabit network. Then it may be a problem with the NIC settings.

There are several reasons why broadband internet is slow:

1. The bandwidth of the ** server accessed is narrow or the server is busy;

2. Computer-related reasons, such as low computer configuration or weak system processing power;

3. It may be a virus or Trojan horse that causes slow Internet speed.

4 Using a router to share the Internet leads to slow network speed;

5 modem device is unstable;

6. Line reasons (such as long line, noisy line, poor quality of the entrance line, change of the user's line and other factors).

If the above instructions still do not solve the problem, you can contact human customer service for processing.

100M fiber is 100Mbps, which is equivalent to the capacity concept of 1GB of a movie as we usually understand it is 100 8=

Internet speed is affected by a number of factors, such as server bandwidth, such as network congestion, etc.

Find a dedicated telecom speed test** to test the speed, if it is less than 10mb s, complain.

The moisture is there, so the home-grade routers are like this, depending on whether your current speed meets your needs. If it doesn't work, then replace the router and wireless network card, it is best to replace it with a 5G channel, which has less interference than the channel you are using now.

This is all advertised as a support protocol, which is Gigabit. In fact, it is very difficult to reach Gigabit, routers and wireless network cards need to support Gigabit, this is not easy to say if the brand is used, I do all enterprise-level wireless, and it is better to not know which one is better for home use.

As mentioned above, the main problem is the protocol and maximum speed that the router and network card can support.

This may not be able to solve it, basically the signal coverage is about the same, and if the previous coverage is not good, the replacement is also about the same. If the signal is not satisfactory, then it is necessary to add relay equipment.

Whether it is optical fiber or network cable, as long as it is based on IP network data transmission, in order to provide higher transmission quality in various transmission channels, it is inevitable to add some control signals to the transmitted bytes, such as address fields and frame check fields, the specific structure is as follows:

As can be seen from the above figure, in addition to the data column is the useful information that really needs to be transmitted, the others are all means to ensure the normal transmission of information, which is "redundant" for the data, so no matter how high the bandwidth, it is essential to waste some resources to transmit these redundant information, so that the circuit utilization rate can not reach 100%, and the actual bandwidth of 100m optical fiber is generally about 80-90m.

The broadband network speed is slow, and it can't reach the maximum speed, so the maximum speed of the optical fiber is 100 megabits.