Why does the hose connected to the bottom of the toilet old burst?

The connecting hose under the toilet is the water inlet pipe, and there are two reasons why the water inlet pipe is old and bursting.

One is that the water inlet pressure is too large, and the other is that the quality of the water inlet pipe is not good.

There are two ways to solve the problem, one is to reduce the inlet valve to make the inlet pressure a little smaller, and the other is to replace the inlet pipe with a stainless steel bellows, and it is impossible to burst if the hose is plastic and replaced with an all-metal inlet pipe.

The pressure of the water pipe is high, and the quality of the hose is not up to standard, so it will burst. This hose must be bought ***, brand.

One is that the quality is too poor, and the second is that the water pressure is too high.

Because the pressure of your tap water is too high, you can put the switch on the toilet bowl in half, or put 1 3 of the total amount, so that your pipe will not burst.

The bottom of the toilet leaks water, generally speaking, it is the leakage of the metal hose and the toilet connection, the main reason is that the metal hose bursts and then the metal hose and the toilet connection leakage, so it is necessary to replace the metal hose in time. This is that if there is a leak in the place where the metal hose is connected to the toilet, it will need to be glued with some glass glue, if it is too little and too thin, there will be gaps in long-term use. Therefore, in the case of a joint, it takes 24-48 hours and do not use the toilet.

There are several reasons for a leak at the bottom of the toilet, and it depends on what kind of situation your home belongs to, so that it will be easier to repair. 1. The toilet was not installed properly when it was installed, resulting in the misalignment of the sewage outlet on the ground with the toilet sewage caliber. In this way, yellow water, water and foul smell will come out.

2. The installation is not professional, and the flange is not installed (the flange has a good fixing and anti-spill effect) 3. Long-term use is suitable for the loosening of the toilet and the ground. 4. The problem of the toilet toilet itself, there are cracks in the ceramic (rare).

Find out the real cause of the leak at the bottom of the toilet bowl and see if it is a leak at the bottom of the toilet bowl or the toilet flush, or if there is a blockage under the toilet.

If the rim of the toilet is leaking, just scrape the glue off the rim. If a hard object clogs the toilet, you need to disassemble the toilet bowl and then glue it to fix it. Or due to the long use of time, the toilet bottom accessories are loose and leaking, then glue and replace the accessories.

1. Find out the real cause of the leakage at the bottom of the toilet, and see if it is a leak at the bottom of the toilet or the toilet flush, or a blockage under the toilet.

2. If the edge of the toilet is leaking, then scrape the edge of the glue clean.

3. If the toilet is blocked by a hard object, it needs to be disassembled and then glued and fixed.

4. Or if the toilet bottom fittings are loose and leaking due to long use, then glue and replace the fittings.

Precautions;

1. Before the installation of the toilet, you should check the levelness of the sewage pipe and the ground, check whether there is any blockage of sediment, waste paper and other debris in the pipe, and also check whether the ground is horizontal before and after the installation of the toilet.

2. Confirm the center of the sewage pipe, the confirmation method is to turn the toilet over, and then determine the center on the sewage outlet of the toilet, and at the same time draw a cross center line at the center, and the cross center line should extend to the bottom of the toilet and the feet around it.

3. First align the cross line between the toilet bowl and the ground sewage outlet, and then ensure that the toilet is installed horizontally, and then press the sealing ring tightly, and then you can install the screws and decorative caps of the anchors.

If there is a leak at the bottom, first clean the glue around it and clean up the sewage. Then recoat it with sealant so that you don't miss anything, and wait until the glue is cured.

It's good to go to the hardware market and buy a good bottle of glass glue to beat it, but wipe the water stains dry before you deal with them, and there should be no dirt on them.

When the toilet is flushed, how to repair the dirty water leaking at the bottom?

1.Check if the flush switch is reset. Some toilets have plastic flush switches that occasionally get stuck after a long period of wear and tear, and if they can't be replaced, the bottom of the toilet will leak. In general, it can be reset by repeating the switch a few times.

2.Check whether the rubber gasket at the outlet under the ball valve is aging, and whether the bottom of the toilet bowl is not tightly sealed and whether it is leaking. If any problems are found, they need to be replaced.

3.Check whether the connection between the spherical float of the water tank and the water inlet switch is loose, whether the float is in place, and whether the switch is not closed, resulting in continuous water flow. When the water is full, water will flow out of the vertical drain as long as the joint between the float and the water valve switch is tightened.

4.If the rubber ball valve is damaged, the seal is not tight, and the bottom of the toilet is leaking, it needs to be replaced immediately.

5.A leak at the bottom of the toilet bowl is basically a drain valve problem. Check the condition of the rubber plug at the outlet of the water tank.

If the rubber plug at the water outlet is damaged or blocked by foreign objects, it means that the rubber plug is not tightly sealed, and it will also cause the toilet to run water. If the water supply pipe in the tank is not placed correctly, it will affect it to a greater or lesser extent.

6.The sealing flange connecting the toilet spout to the floor drain is not in place. Glass glue.

It only plays the role of fixing the position of the toilet on the ground, and it cannot be drained when the toilet is draining. If the sewer main drains smoothly, it will not leak out even if the flange is slightly misaligned. In response to this situation, we need to disassemble the toilet for repair, or buy a new flange to reinstall it, and then fix the toilet with glass glue.

7.The bottom of the toilet is leaking. Water inlet metal hose.

There is usually a leak in the connection with the toilet. The main reason is that the metal hose bursts, and then the connection between the metal hose and the toilet leaks, and the metal hose needs to be replaced in time. That is, if there is a leak in the connection between the metal hose and the toilet, it needs to be glued with some glass glue.

If it is too little or too thin, cracks will appear in long-term use. Therefore, in the case of combined surgery, it takes 24-48 hours. Don't use the toilet.

The leakage at the bottom of the bathroom must be repaired in time so as not to affect the normal life of the family. In general, we should pay attention to maintenance when using the toilet. We can use toilet cleaner to clean the toilet regularly to keep the bathroom clean and hygienic, so that the family will have a better toilet environment.

The above is all about how to repair the dirty water leakage at the bottom when the toilet is flushed, I hope it will help you!

We must shovel the original glue clean, and then clean the surroundings, and then use glass glue to seal the edge, you can also choose the sewing agent to seal the edge, you can use water without leakage to seal the edge.

Be sure to remove the base of the toilet, find the root cause of the problem, replace it in time if the pipe breaks, and also pay attention to the connection between the toilet and the sewer pipe.

From the back of the toilet away from the side of the water inlet pipe, hold a wrench, and unscrew it to replace it by feeling.

No, it doesn't matter if the one-piece toilet is close to the back wall, only the distance between the left (water inlet) wall, too close to the construction, call a professional try, the wrench may be upright by feel.

If you can put glass glue on the cracked place, wait for the glass glue to dry and see if you can stop the leakage.

I've also installed countless toilets, and I haven't had a situation where I can't replace them.

If the operating space is too small, then it can only be discontinued, moved and reinstalled. Remember to use a better hose this time.

Find a capable man, what's the difficulty, but also buy a good hose, find the most expensive one, just a few dollars more.

In this case, you can judge that the flange of the bottom is broken. (If the contact between the toilet outlet and the drain is combined with a flange, it will leak if it is broken, and it has nothing to do with the glue that fixes the toilet).

Mr. Ma from Baoshan South Road called to say that the toilet at home could not be closed tightly for some reason, and he could only watch the water flow away. At Mr. Xiong's house in Baiyun District, the toilet switch could not be turned off and could not be used normally. There are also many citizens who report that the water bill has risen, but they don't know where the water leaks to.

To find out the cause of a leaking toilet, there are three things that can be checked. "96811 convenience master Zeng analyzed: one is to detect the water tank accessories, if the water meter no longer runs after closing the triangle valve, it means that there is a problem with the water tank accessories.

The "core" in the tank is the main heart of the toilet, and it depends on it for water intake and drainage. Many water tank leaks are due to corrosion and aging of accessories: the sealing gasket is stiff and will not be sealed, the spring embroidery of the switch is not flexible, the water inlet valve cannot be automatically closed when it reaches a certain water level, the water level exceeds the drainage line, the switch fails, the sewage flows backwards, and the flush is not clean.

To solve this leakage problem, you don't need to replace the entire toilet, just change the "core" of the water tank.

There is also the bottom of the toilet that is leaking or clogged. Master Zeng went on to introduce that the bottom leakage makes the floor always wet, mostly due to moldy materials or the water outlet is not aligned with the nozzle and the seal is not done well. After a long time, the accessories are aging, and foreign objects fall on the base to block the toilet, which needs to be disassembled and reinstalled.

In addition, when the hose and the water tank interface leak or the filter does not enter the water, the hose is broken and aging, and the junction is not dense, it is good to replace it with a new hose.

When encountering problems such as toilet running, rising, dripping, and leaking, find a 96811 professional convenience master to come to the door for inspection and maintenance, and you don't have to worry about the "guerrillas" spending money in vain, and the after-sales service is guaranteed.

Answer reason 1: The inlet valve does not have a filter. If there are too many impurities in the water, it will cause blockage to the sealing ring in the water inlet valve, so that the water inlet valve will not be closed when it is working. Due to the loose sealing of the joint, the water of the non-disposable formed drain valve flows into the toilet through the overflow pipe through the interface gap under the action of water pressure, resulting in water leakage.

If the sealing ring is not tightly matched with the pipe wall, the lifting inlet valve that can change the height freely will often cause reason 3 and the design of the water tank is not good. For example, when the water tank is discharged, the float and the float rod will affect the normal reset of the flap and cause water leakage. In addition, the float rod is too long, and the float is too large, which causes friction between the water tank wall, affects the free lifting of the float, and leads to seal failure and water leakage.

Reason 4: The float in the tank is not buoyant enough. Nowadays, many toilet tanks are small, so that although water can be saved, the buoyancy of the float is not enough, so that the float can not turn off the inlet valve after being flooded, so it leaks. In this case, the float will need to be changed, but before changing, calculate the pressure required by the float, and then choose what kind of float according to this.

Reason 5: Inferior material. Some manufacturers blindly reduce production costs, and choose inferior materials to cause cracking at the outlet of the water inlet valve and the water inlet pipe itself during injection molding, resulting in sealing failure, and the water in the water tank flows into the toilet through the overflow pipe of the drain valve, resulting in "long flowing water".

1.Close the angle valve under the toilet tank (some people call it the "figure-eight door"); 2.Drain the toilet tank with water.

Hello dear, there should be limescale in the tap water pipe, because there is a filter at the screw of the hose connecting the toilet, you can unscrew the hose and take the filter out to remove the impurities inside. 1. Use special toilet tools to dredge the first thing to know what causes the blockage, if it is caused by soft materials such as rags, women's paper, rags, etc., you must go to the hardware store or supermarket to buy special toilet tools to dredge. This tool is very simple to use, just face the toilet mouth with one end and squeeze it down forcefully to unclog the toilet bowl through pressure.

1. Before choosing a toilet on the market, first determine the size of the water in the seat (i.e., the distance from wall to wall). Before installation, please make sure that the product accessories you choose, completed, please carefully review this manual and learn about some products.

2. Determine the height of the drain according to the condition of the toilet and cut off the rest of the part. The goal is to make the plumbing and toilet bottom more consistent. Start by using a hacksaw or cornea for the sewer according to the horizontal height of the centimeter, because the flange of the toilet bowl is soft.

If it is not centimeters high, there may be water seepage problems, and centimeters are more tightly fitted.

3. Measure the pit distance. Before choosing a toilet, first determine the size of the water inside the house, that is, the distance from the wall to the water. When using a toilet, if you want to decorate the tiles, you must measure the pit distance after applying the tiles. Otherwise, the toilet will be bought back and cannot be installed.

4. Install the flange ring provided with the toilet at the drain. Remember to press hard to ensure the compaction of the flange ring and toilet drain. Place the flange on the toilet drain.

Then carefully align the lower hose and lower it smoothly. At this point, the wall of the sewer pipe is inserted into the viscous clay of the flange for sealing.

5. After the water test is completed, start to install the cover.

6. Glue around the toilet, this step is also very important, not only to stabilize the toilet, but also to prevent the smell of the net from being released from the toilet. Therefore, we will not only fight, but also four whole weeks. At the intersection of the toilet bowl and the outer surface of the floor, since the toilet bowl and the floor are not one, a joint seal transparent sealant can be used for agitation, and the outer opening of the toilet bowl is sealed to maintain the integrity of the floor.

Some bathroom water can clog around the toilet bowl. Note: If you need to install the set screws, first apply a special sealant installed in the toilet bowl evenly over the outside 2cm of the toilet base.

The drain of the toilet bowl should be pulled towards the center of the drain. Expansion bolts are located on the left and right sides of the toilet, remove the toilet, punch holes and raised bolts.

7. Install or debug the water tank accessories.

8. After installing the toilet, wait until the glass glue (putty) or cement mortar has solidified before releasing water. The curing time is usually 24 hours.