-
CPU epidermis? Do you mean that aluminum case?
Did you pry it or what?
If you pried it.
Let's change it. I don't know if I can return to the factory and paste another one for you.
Sweat. What's not to toss, toss this.
If it is a white paste or silver (hard after aging and solidification) on the surface of the CPU aluminum shell.
It's silicone grease.
Just buy one and paint it.
Ice grease of Extreme Freeze Cool is recommended.
15 lz with Raven 2? There are not many people who are willing to use the chassis well these days, I use the ANTEC P193
The work of LZ cable management needs to be strengthened
-
It shouldn't be possible for you to shave the epidermis, it's just a yellowish-white layer, not the epidermis. Add some silicone grease and see how the temperature goes! If it's still 80 degrees, it's useless to add anything!
-
Buy silicone in the computer city! Cheap, a few bucks, take off the fan, paint, install the fan.
-
Coated with thermally conductive silice, only four or five pieces a bottle. The layer of gray on the CPU is the legendary silicone grease, you cross it out and it will affect the heat conduction, it is recommended that you clean up the original silicone grease and reapply the silicone grease, the silicone grease is generally squeezed a little in the middle of the CPU, not too much, just the size of a mung bean, and then use a clean elastic plastic sheet (generally can be found at home, like the packaging shell of some goods, cut off a strip), help smear, must be even, the thickness should be as consistent as possible, Cover the entire metal surface of the CPU protruding from it, and then attach the heatsink to it.
-
Not afraid of dripping. Find someone who can pretend to rub silicone grease on it, and you're good to go.
I can't pretend it myself.
-
80c51 has 5 intermediate interrupt sources, 80c52 has 6 interrupt sources, each entry address.
0003h-000ah external bai interrupt 0 interrupt address area duzhi000bh-0012h timer.
DAO counter 0 interrupt interrupt address area.
Reset RST makes the single-chip microcomputer enter a certain initial state, and the PC value is zeroed (0000h) and each SFR is given an initial value, such as: P0-P3=offhacc=0 tho=0 tlo=0 th1=0 sp=7 psw=0···
-
1.There is something wrong with the heat dissipation, and it is recommended to install a fan in the case.
2.Too high a temperature will shorten the life of the CPU.
3.See if there is a problem with the thermally conductive silicone between the fan and the CPU, buy silicone and recoat it to install it.
-
Yes, the special effects will not get stuck at the low point, and it is very smooth!
-
Unless you use an inter board, generally all boards use inter chips, so it will not be displayed, for example, Gigabyte, ASRock and other chips are a lot of inter but at first only display, Gigabyte, ASRock, but some machines will display the CPU model and frequency according to the motherboard!
-
The inter logo will not be displayed, and the display logo is the *** that the motherboard manufacturer has pre-burned into the motherboard in the motherboard, but the CPU model and main frequency will be displayed when the parameters are displayed.
-
You have a virus, or you have too much boot software
-
It may be that the antivirus software is consumed when it starts, or the automatic IP you use will also be like this, and then it will be a problem with your system.
-
There are too many boot programs on the system, and there will be a high CPU usage when the antivirus software is launched with the system.
-
Usually you are poisoned or Trojan.
-
First check what is the process that makes you mark to 100 usage?
I'll do the same with boot, but I'm not poisoned! Because there is a Rising installed, it is a problem with Rising, but after about 5 seconds, it will be fine!
-
The problem of the power supply is relatively big, you must not try again, be careful to burn the motherboard, maybe the motherboard has been sacrificed, many times many people forget the power supply, thinking that the CPU fan is turning the light on again to think that the power supply is good, that will only hang up the motherboard. QQ group 51649892
-
First look at your connection for problems, and then look at the hardware problems.
-
The power supply is underpowered I've also encountered it.
Change the power supply.
-
1. Light up the display to see if it is normal, if it is normal, it means that the display and display circuit are normal, if it is not normal, check this equipment.
2. Enter the BIOS, see if it is successful, if it is successful, it means that the CPU, motherboard, and memory are normal, and the next step is checked, if it fails, check the three devices.
3. If the above is successful, check the hard disk, mainly in the boot area.
-
Restore the BIOS default settings to see if it works. If it doesn't work, take it and fix it.
-
That you are born to be that thing, and the hot performance is not good... You've been on the computer for a long time, and you should be able to clean up the dust, and you should be able to do the other thing, and the machine... It's time to change...
-
Is it that there is no fan installed or that the fan is too dirty? It is recommended to install a fan or clean up the CPU.
-
Change the heat dissipation, and if you don't change it, it will be unstable.
Thermal performance is a very important performance indicator for computer equipment. If the heat dissipation performance of the device is not good, it will affect the running speed of the device, resulting in poor operation of the device, crash, etc.; Worse cases can lead to equipment failure, hardware burnout, etc. >>>More
Yes, it's hanging, and the operation method is as follows: >>>More
Soak in lightly salted water for 15 minutes before rinsing with water.
If the dog only has a pimple in ** and is not accompanied by other symptoms, it should be caused by two reasons. One is that the dog has inflammation in the body, which can be solved by taking anti-inflammatory drugs. The second is the pimple that appears after the dog has been injected. >>>More
The most important thing is the stratum corneum.