The tablet is used to use the boot interface to see what s going on

This situation is generally called a firmware error, similar to the computer's system disk damage or error, even if you put it all day, or stay in that interface, solution: a computer (desktop, notebook can be), a data cable, go to the Internet to search for your tablet model's flash package or firmware package and ** to the computer (desktop or notebook), after that, generally this flash program will have 3 basic (driver, firmware, firmware installer) and sometimes there is another manual or the like, you can refer to, Under normal circumstances, the flashing is as follows, but the specific may change with you**Flashing package, you can make a reference: **Good flashing package is installed on the computer, if you need to decompress it, decompress it, and then the tablet is turned off, generally press other ** keys in addition to the boot button, press together (it is best to press with one hand, and the other hand should hold the data cable), and then in the case of pressing, connect the desktop and tablet with a data cable, after that, the computer generally shows that there is no problem with the driver of this device, After you enter this, choose to find it manually, select the driver in the folder you just flashed the package and install it, after installation, open the firmware installer, when the display is connected, just in the firmware selection there, select the firmware in your **flash package, and then select the installation in the firmware program, generally install it for 1 minute, after installation, exit the installer first, and the hand can generally be let go (generally you can let go after installing the driver, this looks at the instructions), the tablet can try to boot on, (Flashing sometimes takes 1 or 3 times to be good, this depends on how you actually flash.)

Probably flashing is like the above,Generally 1 driver 2 firmware program 3 firmware such steps,Sometimes the firmware program is opened first and then the driver is installed and then the firmware is installed,This depends on the instructions in your flashing package。 In addition to the above methods, it can only be repaired, but the maintenance place is the same as the brush, but it is just someone else's brush.

The memory is out and it restarts automatically.

Summary. Hello, the tablet has been in the boot interface, the method is 1 first remove the battery, unplug the power plug, press and hold the power button for about 5 seconds, and then plug in the power to see if it can be turned on, if it still can't be turned on, continue the following steps. 2 Remove the battery, unplug the power plug, and open the back cover screw with a Phillips screwdriver.

There is an opening on one side of the cover, and the cover can be removed by gently cocking it along the opening with a screwdriver. 3. After removing the cover, find the memory module, and use a screwdriver to gently open the clips on both sides of the memory module, so that the memory module can be released. Gently remove the memory module and wait a few moments before putting it back on.

4. Cover the cover plate in turn according to the disassembly method, install the battery, turn on the power button and turn it on again. Dear, the above is my summary of your problem, do you see if there is anything else you need me to help you with.

Hello, the tablet has been in the boot interface, the method is 1 first remove the battery, unplug the power plug, press and hold the power button for about 5 seconds, and then plug in the power to see if it can be turned on, if it still can't be turned on, continue the following steps. 2 Remove the battery, unplug the power plug, and open the back cover screw with a Phillips screwdriver. There is an opening on one side of the cover, and the cover can be removed by gently lifting it along the opening with a screwdriver.

3. After removing the cover, find the memory module, and use a screwdriver to gently open the clips on both sides of the memory module, so that the memory module can be released. Gently remove the memory Michi strip and wait a while before putting it back on. 4. Cover the cover plate in turn according to the disassembly method, install the battery, turn on the power button and turn it on again.

Dear, the above is my summary of your problem, do you see if you have anything else to ask me to help you?

These are the ones that have been flashing.

There are two possibilities, one is, you can try to take out your memory card, because the memory card is not a high-speed card, it will affect the boot, and the other is to use the button to restore the tablet to factory settings, this method is not recommended to use, the risk is too great, data loss or something is very wanton, build an imitation hail Shi you have time to play after-sales**, they will**guide how to operate correctly, go to after-sales can also, this situation is generally an upgrade or re-security system on it.

Which is the power on button.

Top right corner.

1. First charge the tablet, connect the data cable charger according to the manual, fully charge, and after the charging is completed, press the power button on the side or bottom of the tablet to turn on (the specific button position is subject to the model of different tablet computers).

2. The tablet can change the angle of use according to the usage habits, which is mainly divided into four modes of use: tablet mode, portable mode, painting mode, and notebook mode. The corresponding mode requires a keyboard, laptop case, stylus, etc.

Notebooks can choose to buy additional protective cases with their favorite Zen patterns according to different models, and whether the screen needs a protective film needs to be selected according to personal usage habits. Some screens are not suitable for screen protectors, but you need to pay extra attention to the screen during use to avoid scratches and oil stains.

3. The biggest difference between a tablet and a notebook is that the heavy computer becomes a thin and light model similar to a board, and the tablet is a touch screen, which improves the portability and sensitivity of the overall use. All programs are pre-set at the factory after booting, and if you need to add personalized programs, you need to connect to the Wi-Fi network by yourself**.

4. Connect to the wireless network and try to click Settings to personalize your tablet. According to the prompts, change the display of the screen, brightness, whether it is dormant or not, etc. one by one. Generally, the screen will have the word "return",You can touch the screen to click to return,Some models will additionally set the return button or home button on the screen frame,Similar to a mobile phone,You can return after the setting is completed。

5. The overall system operation of the tablet computer is similar to that of a notebook, so it can be well used in work, study and entertainment. You can send and receive emails, documents, take photos, record audio, chat remotely, watch movies, listen**, study courses, play games, etc. The corresponding program needs to touch the screen to enter, and multi-window operation will slow down the running speed of the tablet.