Dual hard disks now want to disassemble a disk down, how to deal with the hard disk data

Hello buddy,This situation,Buddy thinks it's also good,If the data is larger,But that thing,You need a mobile hard disk,If the buddy has a mobile hard disk,It's easier to do,There will be 1 disk and 2 disks that need data or key data to be copied to the mobile hard disk,But the number of data you don't want depends on the buddy,It's easier to do it with a mobile hard disk,Confirm that they are all copied,Just install the two hard disks directly in the two computers,Direct partition reinstallation of the system is the result。 But if there is no mobile hard disk, then copy the data of 1 disk to 2 disks, and then install 1 disk in another computer to partition and reinstall the system, after installing the system, reload 2 disks and then load 2 disks into 1 disk, and then install 2 disks into another computer partition, reinstall the system, after installing the system, remove it and install it on 1 disk of that computer, copy the data of the original 2 disks again, and then install 2 disks back to another computer, this method has a limitation is 320 that hard disk, It can accommodate all the data of 1 disk and 2 disks, and the operation is still a little troublesome, but don't borrow other USB flash drives or mobile hard disks, buddy consider it, can it be completed, thank you!

If you don't have anything important on the 1T disk, it is directly divided into 5 zones (note that the first main partition is activated, each zone is larger than your 320g corresponding partition) and then directly use Ghost's partition to partition to copy it, so that you can continue to maintain the use of the 320G disk If there are too many private collections on the 1T, then I didn't say it.

This problem is the reason why the motherboard can't recognize which is the main hard disk, and some motherboards need to jump a line when they install dual hard disks back, and the connection to the motherboard must be connected correctly, and it will not work if it is not connected correctly.

You first check if the motherboard of a host is equipped with dual hard disks, whether it jumps the wire, which pair to jump, and then after the operation, install the hard disk of the system disk, be sure to pay attention to the belt connected to the motherboard, generally speaking, the remote port is the main port, and the middle port is the main port, start the computer, if passed, then shut down and install the second hard disk.

You put down the battery of the motherboard, try it, and see if the master and slave of your two hard disks are wrong, if not, just connect one by one, and see if the system is on that hard disk.

Summary. Hello, dear. You only have two hard drives left, and one disk inside each of them, and how you read your data depends on your specific needs and hardware conditions.

Here are a few ways: RAID recovery: You have previously used a RAID (Redundant Disk Array) configuration to organize your data, and only two of these hard drives are currently available, you can try using a RAID recovery tool to restore your data.

This requires the use of specific software or hardware tools and requires a certain amount of expertise. Data recovery services: If you are not familiar with data recovery, or your attempts to recover on your own have not been successful, you can consider contacting a professional data recovery service provider.

They have specialized equipment and technology to be able to extract data from corrupted hard drives. Professional Tools: There are some commercially available data recovery software that can do data recovery on a single hard drive.

You are able to confirm that both disks are working and that there are no other special configurations such as RAID, and you can try to use these software to read and recover data.

Hello, dear. You only have two hard drives left, and one disk inside each of them, and how you read your data depends on your specific needs and hardware conditions. Here are a few ways to do it:

RAID recovery: You have previously used a RAID (Independent Redundant Disk Array) configuration to organize your data, and only two of these hard drives are currently available, you can try using a RAID recovery tool to restore your data. This requires the use of specific software or hardware tools and requires a certain amount of expertise.

Data recovery services: If you are not familiar with data recovery, or if you have tried to recover on your own without success, you may consider contacting a professional data recovery service provider. They have specialized equipment and technology to be able to extract data from corrupted hard drives.

Professional Tools: There are some commercially available data recovery software that can perform data recovery on a single Sen's hard drive. You are able to confirm that both disks are working and that there are no other special configurations such as RAID, and you can try to use these software to read and recover data.

Hello, dear. Whichever option you choose, keep in mind the following: Back up your current hard drive mirroring bridge or original data before proceeding to prevent further damage or data loss.

Try to avoid physical dispersion of the hard disk to avoid further damage to the surface of the disk or internal components. If you are not sure of your abilities, please seek professional help as soon as possible to improve the success rate of data recovery.