What to do if the guitar strings are too high? How to adjust the height of the guitar strings

People in big shopping malls are definitely yes, if you want to ask, you have to get a professional piano shop to ask.

On this issue, it can be adjusted, it depends on whether you are a few frets high in front or a few frets in the back, if the first few frets are higher, it is recommended to grind the pillow, if it is a few frets high, it is recommended to grind the string bridge. If the whole feels high, then grind both sides. Don't be afraid, take more time, grind a little less at a time, grind a little, give it a try, there will be no risk, just be careful.

You can add me.

If you are not familiar with it, it is best not to grind it yourself, you have to see first, whether your neck is normal straight, if the neck has curvature, you don't want to grind the pillow by yourself, you have to take it to the place where the piano is repaired by the piano shop to get the neck down, if not, you have to change the piano.

If the neck is fine, and the other parts are normal, you can grind the pillow, that is, each string has a concave place at the pillow, just grind there, don't use too coarse tools to grind, grind two or three times to play, don't grind too much at once, you can also use sandpaper.

Contact me again if you have questions.

There are 2 ways to lower the pitch by one degree, and pressing it softer can effectively solve the problem.

Polishing the pillow can be made for 10 yuan at the piano store, or it is best to change a pillow with yak bones if you can get it.

Change the piano, the strings are high and you can't play at all, your hands will hurt very much, the guitar you buy is definitely not expensive, whether you are a professional guitar or not, it is recommended not to buy a cheap guitar, at least more than 500 can be used. Otherwise, the sound quality is not good, the strings are high, and the tone is not accurate.

The guitar has a high string pitch, and it is necessary to turn the wrench in the direction of the 1st string to "tighten" the neck, and there is an irregular bend after the neck is "twisted", which is generally horizontal or vertical's'bend, in this case, you need to find a professional to repair it.

Don't loosen the string when adjusting the neck, the string needs to be tightened after the string is sent to the Zen call shed, and the string is repeatedly tightened to the string. When adjusting the neck, the amplitude of the wrench can not be too large, the amplitude of the adjustment can not exceed 45 degrees, and the guitar can be erected after turning, which can reduce the force on the neck, and there will be an adaptation process between the neck and the steel bar, which can be adjusted many times.

Guitar. If the guitar does not adjust the neck for a long time, there may be a situation where the wrench will not move, so it is best to find a professional piano store to adjust it when adjusting it to avoid damaging the neck. It is very normal for the guitar to have one or two frets in general, which may be affected by humidity and temperature, in this case, it is necessary to determine whether the strings are damaged by external factors.

When the strings are installed, the new strings and the old strings also need to be adapted, so it is necessary to distinguish some situations correctly. The guitar strings are too high.

You can use an Allen wrench to lower it.

Make adjustments. The guitar hex wrench is mainly used to adjust the neck, and the general guitar neck has a steel bar inside, and there is a screw with a hexagonal at the end of the steel bar at the guitar sound hole, and the guitar hex wrench is here to screw this steel bar.

Guitar. If the guitar fret, or the string pitch is too high, you can adjust this steel bar to solve, when using, insert the hex wrench into the hexagon of the guitar steel bar, rotate clockwise, the string distance will become lower, at this time the headstock is tilted back, counterclockwise rotation, the distance between the string and the fingerboard will become higher. The string pitch is the distance between the string and the fingerboard, the lower the string pitch, the better it is to press, but if it is too low, it will hit the fret, and if the string distance is high, it will be laborious to press, affecting the feel and affecting the performance.

Guitar Pitch Height Adjustment Method:

1. Neck adjustment:

The neck adjustment is relatively easy to operate, and we can insert the metal hex wrench that comes with the purchase of the guitar into the adjustment jack at the guitar sound hole. Rotate clockwise (in the direction of 3) and the neck will convex, lowering the string spacing. Rotate counterclockwise (in the direction of 2) and the neck will be concave and the string pitch will be raised.

In general, the slow string pitch is too high due to the forward bending of the neck, and clockwise adjustment is sufficient.

Note: The strings do not need to be fully relaxed, the strings are kept pulling, and we can see the effect immediately when adjusting. The single adjustment amplitude should not be too large to avoid damage to the neck.

2. Chord pillow adjustment:

The adjustment of the string pillow is divided into the upper string pillow of the headstock part and the lower string pillow carried by the piano yard below the sound hole, the operation is slightly cumbersome, there is a certain degree of difficulty, it is recommended that experienced friends try, beginners try to find experienced friends to help, but the replacement cost of the string pillow is not too high, and friends who want to try it can also get started and experience.

The adjustment of the string pillow is mainly to reduce the height of the chord pillow by grinding the bottom of the chord pillow through fine sandpaper, so as to achieve the purpose of reducing the chord distance.

Note: When sanding, it should be polished as a whole, the bottom of the chord pillow should be kept smooth, not uneven, and the sandpaper should also be selected as a finer one, and tested in time to avoid overheating.

The correct way to measure chord pitch:

The standard guitar string spacing is: 6 strings, 1 fret string, 1 fret string accumulates, and it should be measured with a thickness gauge difference shed volt); 6-string, 12-string, 12-fret veneer guitar standard, plywood appropriately heightened).

The guitar strings are too tall and can be lowered by adjusting the guitar bridge or neck.

Here's a detailed look at how to reduce the high slag of guitar strings and what to look out for.

1. Adjust the guitar neck

To lower the height of a guitar string, you first need to check its spacing. If the string spacing is too large, the guitar neck needs to be adjusted. You can use a guitar caliper or use your own fingers to measure.

Generally speaking, starting at the position where the current string should be at the 12th fret and going to the first fret of the guitar less than 1 16 inches (about millimeters) is too small, and more than 1 8 inches (about millimeters) is too large.

Next, loosen all the strings and use a guitar tuning wrench to open the adjustment screws attached to the guitar neck to loosen. Then, carefully observe the distance between the string and the fretboard and adjust it step by step until you get the desired spacing.

This can be time-consuming and patient, so attention to detail is required to determine when the string height is the right one.

2. Adjust the guitar bridge

Another way is to reduce the height of the guitar strings by adjusting the height of the guitar bridge. On some guitars, you can directly adjust the height of the bridge section to control the string height. This can be fine-tuned by rotating the adjustment screw, or using a screwdriver.

If you want to refine the string height on top of the bridge height shout, the best way to do this is to remove the electronics of an electric or semi-electric guitar, don't forget to loosen the strings completely before making adjustments, and save them in the correct position before breaking. When you're done adjusting, reassemble all the electronics.

3. Precautions

When it comes to adjusting the guitar neck or bridge, you need to be very careful. Too much force can disrupt the bridge's center of gravity and disrupt the entire sound system. Also, be especially careful when adjusting your guitar neck, as over-tuning may result in too much physical stress, which can lead to a broken neck.

Fourth, please find a professional to help

Finally, if you want to lower the height of the guitar strings, you must be cautious if you have no relevant experience. If you are experiencing technical difficulties, you can also seek advice and assistance from professionals.

Some guitar shops or repair studios can provide you with tuning services tailored to your guitar to help you find the best string height to play better.