How to maintain and maintain the display?

1. Avoid burning out the inside of the screenCRT display can burn out due to long-term work, and the same is true for LCD, so you must pay attention to it, if you don't use it, you must turn off the display, or reduce the display brightness of the display, otherwise it will lead to internal burnout or aging for a long time. This damage, once it occurs, is permanent and irreparable. In addition, if a fixed content is displayed continuously for a long time, it may cause some LCD pixels to overheat, which may cause internal burnout.

2. Pay attention to maintaining humidity, generally keep the humidity between 30% and 80%, the display can work normally, but once the indoor humidity is higher than 80%, condensation will occur inside the display. The power transformer and other coils inside it are also prone to leakage after being wet, and may even cause short circuits in the wiring; The high-voltage part of the display is very prone to discharge; The components in the machine are prone to rust and corrosion, and in severe cases, the circuit board will be short-circuited. Therefore, the LCD display must pay attention to moisture-proof, and the display that has not been used for a long time can be powered on regularly for a period of time, so that the heat generated by the display when it is working will drive out the moisture in the machine.

Also, don't let anything with moisture properties get into the LCD. If you find a fog, gently wipe it off with a soft cloth before you can turn it on. If the moisture has already entered the LCD, it must be placed in a warmer place to allow the moisture and organics to evaporate.

Powering an LCD with humidity can cause corrosion of the liquid crystal electrodes, which can cause permanent damage.

3. Clean the surface of the display screen correctly If you find that there are stains on the surface of the display, you can gently wipe it off with a soft cloth stained with a little water, do not spill the water directly on the surface of the display, water entering the LCD will cause a short circuit on the screen.

4. Avoid impacting the LCD screen is very fragile, so avoid strong impact and vibration, LCD contains a lot of glass and sensitive electrical components, falling to the floor or other similar strong blows will cause damage to the LCD screen and some other units. Also be careful not to put pressure on the LCD display surface.

5. There is a rule for not taking the automator privately: never disassemble the LCD. Even after being turned off for a long time, the CFL inverter in the background lighting component can still carry a high voltage of about 1000V, which can cause serious personal injury.

So never try to disassemble or alter the LCD display to avoid high pressure. Unauthorized repairs and changes can result in the display temporarily or even permanently rendering it unfunctional. So when your hands and feet are really idle, don't touch the delicate and dangerous LCD!

Stay safe!

Pay attention to dustproof, waterproof and pressure-proof, and cover the monitor with a cloth when shutting down; To keep the display screen clean, you can use a soft cloth to wipe the dust and stains on the screen, be careful not to wipe it with water, it is best to use LCD screen cleaner, spray an appropriate amount of detergent on the cloth to gently wipe the screen, do not spray directly on the screen.

1. The computer monitor is exposed to the air, and if it is used for a long time, it will cause a large amount of dust on its surface, which will seriously affect the daily use. It is important to know that the high pressure generated in the display is more than 10kV, which is very easy to absorb dust particles. Therefore, you can usually use a computer cover to protect the display and block dust.

2. Try not to contact the computer display screen with water, otherwise it is easy to damage the internal components of the computer. Generally speaking, it is relatively safe to keep the moisture on the monitor below 80%, once the stool lead exceeds this value, there may be condensation, resulting in moisture in the internal transformer, and leakage, bringing danger.

3. The computer monitor should pay attention to its heat dissipation, if the heat dissipation function is not good, resulting in too high internal temperature, there may be damage to the picture tube and reduce the service life. At the same time, if the temperature is too high, it will also cause some solder joints to melt, and the display will not work properly, which will burn other components inside.