When going downhill to the top of the slope, use low or high beams

At night, the vehicle should be 150 meters away from each other to close the high beam, switch to low beam, and at the same time should reduce the speed of the vehicle (generally with medium speed), choose a wide and straight place to meet, and when the two cars will be in the wrong place, you can turn on the high beam. When meeting cars on narrow roads, when the two cars are about 50 meters apart and the low beams are still dazzling, the low beams should be turned off and the small lights should be used to ensure safety. After switching to low beam or turning off low beam, if the road surface is unclear, you need to observe the distance situation, and you can continue to turn on the low beam or high beam for observation, but the time should not be too long (method:

A flash is sufficient) so as not to dazzle the driver of the opposite car. However, when intersecting with non-motorized vehicles on narrow roads and narrow bridges, intermittent lights cannot be used to prevent cyclists from dazzling and accidents occur. Effectively control the speed of the vehicle during the day, due to the good line of sight, the speed of the vehicle is easy to control.

However, when driving at night, due to factors such as fewer vehicles, darkness at night, lack of references, and rushing to the road, the speed of the vehicle will accelerate unknowingly. It is extremely dangerous to drive too fast at night, or even at high speed. Because the distance of the car's lights is limited (the high beam is about 150 meters), it is impossible to see beyond this distance.

In particular, when meeting a car, only low beams can be used, and the illumination distance of low beams is only about 30 meters. According to the experiment, when driving at a speed of 55 kilometers per hour at night, the brakes were immediately applied when the situation was found, and the stopping distance was exactly 30 meters.

That is, when the situation is found within the range of low beam illumination, it stops immediately, and there is no gap between the car and the object. Of course, this is when the vehicle condition, road conditions and the driver's response are good, if the speed is higher than this, the vehicle condition, road conditions are poor and the driver's fatigue reaction time is long, the result can be imagined. Therefore, it is important to control the speed of the vehicle when driving at night.

When using high beams on a flat, wide, well-sighted road, the speed of the vehicle can be appropriately accelerated; And when the car encounters uneven road surface or turning or bridges or narrow roads or intersections and other complex situations, it should slow down and slow down, and the speed is generally controlled within 40 kilometers per hour.

When going downhill, you can use low beam or high beam, the key is that you can see the road in front of you, the use of these two lights, the key is not to use high beams when the opposite car is coming to use low beams, so as to avoid the other driver not being able to see the road clearly.

Use high beams when driving at night when approaching the top of an uphill slope. Use high beams when going uphill at night, and replace high beams with low beams when the vehicle approaches the top of the slope. Traffic regulations stipulate that when passing through the top of a slope or at an intersection that is not controlled by a traffic light, the high and low beams should be used alternately.

When driving at night, the headlights are an indispensable aid, and you should not only pay attention not to turn on the fog lights and headlights at the same time, but also know how to use and change the lights.

Precautions for using high beams when driving a motor vehicle at night near the uphill slope crest

When driving the car into the top of the uphill road at night, you should alternately change the high and low beams, so that you can remind the car on the opposite slope, because the car on the slope can not see you, and at the same time you must reasonably control the speed, driving at night, the lights are an indispensable auxiliary tool, not only to pay attention not to turn on the fog lights and headlights together, but also to know how to use and change the lights. When driving at night, low beams should be used when the speed is less than 30 km/h, and the lights can shine more than 30 meters under normal conditions.

Can I use the high beams when driving uphill at night? Yes, because the irradiation distance of the high beam is longer than the low beam, and its irradiation distance is about 100 meters, while the irradiation distance of the low beam is only about 40 meters. And the high beam has a wider irradiation range.

Do you hate "high beam dogs" when driving at night? I hate encountering high beams, the opposite high beams will dazzle your eyes, so you can't see the road clearly, which greatly increases the probability of accidents, so try to use low beams when driving at night. However, high beams are required for high-speed running, and some car owners also use low beams for high-speed running at night.

So do you use low or high beams for high-speed running at night? Traffic police: Don't be brainless, play with your own life.

If you drive on the highway at night, it is best to turn on the high beams. First of all, most of the highway sections have separation belts, and ordinary family cars and SUVs can use high beams without affecting oncoming cars, so they can be used with confidence. Secondly, most of the highway sections do not have street lights.

If low beams are used, the lighting situation will be poor. If the speed of the car is fast, it may not be able to react to any situation on the road, which is easy to cause accidents.

As we all know, most highways are designed with a split lane in the middle, that is, there is a separation in the middle of the lane opposite you. And this isolation facility basically has a light isolation facility. For example, there is a row of street trees in the middle, for example, there are light barriers in some narrow places, basically you don't have to worry too much about the traffic safety of the lane opposite you, because the lights are basically blocked after passing, so you can use it with confidence.

Even if there is occasional light leakage in some places, it is much better than seeing the road clearly with low beams.

The advantage of turning on high beams on the highway is very great, because the irradiation distance of high beams is longer than that of low beams, which is about 100 meters, while the irradiation distance of low beams is only about 40 meters. And the high beam has a wider irradiation range. We can find the traffic signs on the road ahead with our high beams in advance, and then do a good job in advance** to avoid illegal driving.

In addition, we would like to remind everyone that you should never use headlights because the road is well lit. The vehicle's headlights have two functions. First, it is necessary for others to see you.

Second, it's natural to light the way ahead, especially in a tunnel. It is advisable to turn on your headlights to avoid accidents caused by other vehicles not being able to see your car when changing lanes. The rational use of lights, the scientific use of lights, and the standardized use of lights can ensure the safety of car travel, and I hope it will be helpful to new and old drivers.

When driving uphill at night, you should use high beams, you can warn surrounding vehicles to avoid unnecessary trouble, but after going uphill, you should change to low beams.

Yes, if the lighting conditions are not very good, you can use high beams, so as to ensure the safety of driving.

If the lighting conditions are not very good, make high beams and drive.

When driving on the highway at night, do you turn on the high beams or low beams? Whether it is for old drivers or novice drivers, the three words "Yuanguang Dog" can be described as "deeply rooted in the hearts of the people"! Many new and old drivers have this question - do they use high beams or low beams when driving at high speeds at night?

Xiao Wan is here to tell you that if you are driving at high speed at night, it is best to turn on the high beams. First of all, most of the high-speed sections have isolation belts, and the use of high beams in general family cars and SUVs will not affect the oncoming cars on the opposite side, so you can use them with confidence. However, most of the high-speed sections do not have street lights, if you use low beams, the lighting situation will be poor, in the case of fast speed, what conditions on the road may not have time to react, easy to cause accidents.

Of course, if you pass through a highway section without a separation zone, when there is an oncoming car on the opposite side, you still have to switch to low beam to avoid obstructing the view of the oncoming traffic. After the interaction between the cars, switch to the high beams and continue driving. If the other party's high beam gets in the way, you can switch the high and low beam three times in a row to remind the other party that if the other party cuts the low beam, you can also cut the low beam, and if the other party does not react, you can also continue to use the high beam, there is no need to be humble in this situation.

Apart from the highway, what sections of the road are it necessary to use high beams?

If the road lighting is not good in the non-high-speed section, you can use the high beam first, and the opposite car will switch in time to ensure safety.

In addition, I would like to remind everyone to pay attention to one point, do not use headlights because the road lighting is sufficient, and the headlights of the vehicle have two functions, the first is to let others see you, and the second is to illuminate the road in front of you, especially in the tunnel, it is recommended to turn on the headlights, so as not to cause accidents when other vehicles can not see your car when changing lanes. Rational use of lights, scientific use of lights, and standardized use of lights, so as to ensure the safety of car travel.

Turn on the high beams when going uphill, and replace the high beams with low beams when the vehicle approaches the top of the slope.

Traffic laws stipulate that headlights must be turned on when driving at night.

When there is no central isolation facility or no center line on the road to meet traffic, high beams cannot be used within 150 meters from oncoming traffic in the opposite direction;

High beams cannot be used when meeting non-motorized vehicles on narrow bridges and narrow roads without central isolation facilities or center lines;

When a motor vehicle is driving at night without street lights, poor lighting, or in low visibility conditions such as fog, rain, snow, and dust, the high beam cannot be used when the rear vehicle driving in the same direction is driving in close proximity to the vehicle in front.

3.Alternate high and low beams should be used for sharp curves, slopes, arch bridges, pedestrian crossings, or intersections that are not controlled by traffic lights.

4.Remember to turn off the high beams when you will be driving at night

Under normal circumstances, the lighting conditions of urban roads are better, and you can use low beams at night, and you basically don't need high beams. If the lighting is not good, the driver can also use the high beams. However, be sure to turn off your high beams when meeting a car.

If there is any violation of the above behavior, a fine will be imposed and points will be deducted.