Every time you have to power off and restart the tplink route, the music pad can connect to the Inte

Hello. We apologize for the impact on your use. Due to the brief description of your problem and our remote base, we are unable to understand your actual model and doubts, please understand!

If you have other wireless networks nearby, please try to compare:

a. Other networks can be directly connected normally, you can judge that the mobile phone system and hardware function are normal, please try as follows:

1. Signal of wireless network: When the wireless signal signal is weak, it may lead to the inability to connect normally or the application cannot be connected to the network normally, it is recommended to move the mobile device to the strong wireless network signal to try;

2. Abnormal wireless network parameters: In order to avoid abnormal connection due to abnormal wireless network parameters such as DNS, it is recommended that you try to set the wireless network as a static IP assignment.

3. If the above suggestions still cannot be improved, it is not excluded that the compatibility between the routing equipment and the product is caused, and it is recommended that you replace the wireless network or routing equipment to use it;

b. If other networks cannot be directly connected normally, it may be caused by abnormal system or hardware functions

1. Please back up the fuselage data and try to restore factory settings;

2. If it still cannot be improved after recovery, please take the time to go to the local maintenance site to test and process the system and hardware.

If the conditions are limited and you cannot compare with other wireless networks, it is recommended that you conduct a simple investigation based on the above suggestions, and if it cannot be improved, please send it to the repair site in time.

Repair site information can be found at:

For the problem of the router itself, you can set the Lepad fixed IP, which directly corresponds to the router's DNS.

You can consider buying a router with a good point.

Seven times five eighths plus two-thirds divided by eight fifths = 125/48

After the tplink router is reset, it can go to the Internet for a while, and it is disconnected, hello dear! Cause 1: The network line is faulty.

Home network environment wiring]: 1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer. Reason 2:

The router has an incorrect Internet configuration and you need to reconfigure the router. Solution: Reset the router and set dialing again.

How to reset the router: Method, there is a button [RESET] button behind the router, press and hold for 5 seconds, and the indicator light on the router panel will be off and then on, which means that the router has been reset. Set up router dialing:

The IP and DNS settings of the computer are automatically obtained. 1. Open the browser - enter the general router address is this or view the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin). 2. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter your Internet username and password according to the prompts, and save.

3. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit. Reason 3:

Router hardware is damaged. Workaround: Replace the router with a new one.

Cause: A problem with the router.

1. First reset the router. Press the reset key on your router. If you don't have a network after restarting, follow the steps below to set up the network again.

2. Enter or enter in the browser.

3. Enter your administrator password after entering. It's generally admin.

4. Find the "Setup Wizard".

5. Then click "Next".

6. Select the second virtual dial pointed by the arrow.

7. Enter your Internet access and password in the box that pops up. I don't know myself and the password to call ** to install broadband or optical fiber customer service for you.

8. Then enter your wireless network password in the box that pops up. That is, your wifi password.

9. Finally, click Done. So we're all set. Turn the broadband connection back on and you're ready to connect to the Internet.

Summary. 1. If you are using a router, disconnect the router for stand-alone dial-up test first.

2. If you have a modem device, you need to pay attention to whether the device is overheating, you can turn it off for a few minutes and then restart it.

3. If the connection is dropped when running the program alone (compared to if it is dropped when playing games), it is recommended to restart the computer to try or reinstall the program;

4. If the entire network is disconnected, please check whether the access cable and the network cable are loose or in poor contact, and try to reseat the line.

5. Check and filter the disconnection caused by computer viruses and scan the whole disk.

After the tplink router is reset, it can go online for a while and then it is disconnected.

1. If you are using a router, disconnect the router for stand-alone dial-up test first. 2. If you have a modem device, you need to pay attention to whether the device is overheating, you can turn it off for a few minutes and then restart it. 3. If the connection is dropped when running the program alone (compared to if it is dropped when playing games), it is recommended to restart the computer to try or reinstall the program; 4. If the entire network is disconnected, please check whether the access cable and the network cable are loose or in poor contact, and try to reseat the line. 5. Check and filter the disconnection caused by computer viruses and scan the whole disk.

I hope mine can help you, take protective measures during the epidemic, wear a mask, and protect yourself. If it's convenient, please give a 5-star like, I wish you good health! All the best for the new year!

After resetting the TPLink router, it is set to automatically obtain IP, and the TP router can access the Internet at first, but it will be disconnected in a few minutes. The network of the optical modem is normal, is the router broken? Yes.

The tp-link wireless router is often disconnected, and it is good to restart

There may be a strong source of signal interference next to the wireless router.

The router firmware and hardware do not match.

Wi-Fi optimization is enabled on the phone.

The wifi transmission power of the wireless router is too small or the device is too far away from the router, and there is a shield in the middle.

Having multiple wireless routers nearby can make a difference.

The hardware of the router's wifi transmitter module or mobile phone's wifi receiving module is faulty.

TP-Link wireless router is often disconnected from the network, and restarting it is good to solve the problem:

Keep your wireless router away from these sources of interference.

Update or roll back the wireless router firmware to find the best firmware version.

Disable Wi-Fi optimization, Disable Do not use unhealthy connections, and select Keep Wi-Fi connections in hibernation.

Set the maximum power of the wireless router to shorten the distance between the wireless router and the device used, and minimize the obstacles between the wireless router and the device.

Change the router channels to 1, 6, and 9 channels to reduce the interaction caused by signal overlap.

Replace your wireless router or phone.

This is generally caused by the defective firmware of the router itself, if you directly find a merchant to change it during the warranty period, I have encountered more than one or two tp-link routers with this problem, and I have used a similar one myself, I can't stand it the next day and return it directly, and now I basically use a fast router.

Routers such as tp-link d-link basically have this problem when used for a long time.

The main thing is that the stability of its firmware is not very good, so it is recommended to check the corresponding model firmware on the official website to upgrade it and try to see if it is stable.

If the landlord is still using the old router that he bought three or five years ago, it is recommended that the landlord replace it directly, after all, the country's network speed has increased very quickly in the past three or five years, and it is directly 100 trillion 200 trillion to start, plus the popularity of smart phones. Smart home devices began to enter thousands of households, more and more networking devices in the home, if it is the kind of low-end old router three or five years ago, it is difficult to meet the current use needs, and it is normal to crash often.

Reasons why the TP-Link router cannot connect to the Internet after powering off:

1. The port response is slow;

2. The router is set to idle time, and the network will be automatically disconnected when the router has no traffic to the set time;

3. There is a problem with the DHCP function of the router;

4. Overheating of the router will cause the router to crash;

5. It is defective or aging.

Solution: Slow port response: you can wait for about half an hour before boarding it, if you can connect it, disconnect it in the computer before shutting down, and the next dial will be easy to dial.

If the router overheats and causes the router to crash: turn off the router for a while before turning on and connecting to the Internet.

The router itself is defective or aging: take it for repair or replace it with a new one.

The router I bought on Jingdong also has this question.,Check it for a long time.,Found that the router DHCP function is unstable.。

That is, it is caused by an error in the router assigning the IP).

If you don't know if you're in this problem, you can follow the steps below to verify God and take a look.

1.If you can't access the Internet, click Start - Run - Enter cmd - and in the command prompt that appears, type ipconfig all

2.Check if the IP4 (or IPv4) IP address is an address like that, if it's an IP error, if it's an IP like that, then it proves that it's not a DHCP problem.

If there is an IP error, the solution is as follows: disable the DHCP function of the router and manually configure the IP in the computer

Manual IP: is a number between 100 and 255.

Subnet Mask: Gateway: Preferred DNS Server Rock Track:

I've never had a disconnection since I clicked on this setting, good luck.

1.Try to specify the IP and DNS manually, when you can access the Internet, start --run --cmd--ipconfig all, you can view the IP address and DNS plus gateway, and manually enter the local connection attributes.

2.Restore factory settings, and then reset the router can have a chance to recover, or you can achieve a more stable purpose by upgrading the router configuration before the travel photograph, please back up the original file first for configuration file upgrade, in case of emergency, the configuration file can be obtained by searching for the router model on the TP official website.

3.Replace the new router, and the hardware of the original router is aging, resulting in the instability of Lianhuixian's connection.

I use a virtual dial-up Internet access,Brought 6 computers to the Internet,Recently, it's always dropped for no reason.、After dropping the line, you can first change a good router to try to let it.,If you can bring it up, it's a router problem.,If it's still a feast.。