Problems with network cables as wires? Can a network cable be used as a wire?

First of all, the network cable is the wire, you only **modem and router power supply, these two power consumption, current is not very large, under normal circumstances, it is bearable, sometimes it is inevitable to encounter special circumstances (such as power outage, power outage is when the current is concentrated).

Again, you put the network signal line and the wire together is absolutely impossible, the power line in the current through the current, will produce electromagnetic induction, the network signal is weak, weak current and strong current walking together is bound to interfere with the network signal of the network signal line, so with the line tester test may be able to pass, but when connected on the computer, it will definitely be seriously dropped, unable to access the Internet.

Finally, it is the problem of induction electricity, you know that each network cable is wrapped with glue, glue belongs to the insulator, is relative insulation, not absolute insulation, the current will produce current outward flow during the transmission process, it will produce induction electricity, when the electrical power consumption is large, the greater the current, how much current can you circulate so small copper wire, the light will lead to the inability to connect to the network normally, the heavy will burn out the copper wire inside, and then burn out the computer's network card and modem, If your network card is integrated, it will burn out the motherboard of the computer, and the consequences will be more serious.

It is recommended not to leave greater hidden dangers in order to save trouble, others are lucky not to have an accident, and it will be too late if something happens.

Absolutely not, the network cable design line is used for weak electricity, and the line is only, and it can only pass more than 20 W.

Even if it can be used, it will dry up the Internet signal, if the equipment with 220V exceeds the overcurrent of the line, it will burn the line and short circuit, at least the computer will be reimbursed, and it will not catch fire.

Mesh cables, usually made of metal or glass. It can be used to transmit information within the network. There are three types of network cables that are commonly used:

Twisted pair, coaxial and fiber optic cables (fiber). A twisted pair is a data transmission line that consists of many pairs of wires. It is characterized by being cheap, so it is widely used, such as our common **line.

It is used to connect to the RJ45 head. It has two kinds of STP and UTP, and we commonly use UTP. Coaxial cable is a cable wire that is wrapped with a copper conductor by layers of insulated wires.

Optical cable is the most advanced network cable at present, but it is more expensive and rarely used in household occasions. To connect to a local area network, a network cable is essential.

There is interference, and the induced voltage is enough to burn your network card, and it's over.

You're a little too bold.

The network cable is too thin to take on large loads. How big is the network line current? How can you use this wire to connect the load?

You can't get on the network with just a network cable.

The condition for accessing the Internet is that your network cable is connected to the network, and you need to obtain an Internet pass, that is, to handle the payment of network access services.

OK. Category 6 wires, a group of four, equivalent to a square copper wire, and a cross partition in it, are absolutely no problem for electrical appliances below two kilowatts. Don't listen to those who only know about books.

The 4 threads are not too thick, and you should be careful to burn the threads. Theoretically, the network cable can be used as a wire, but it is too thin to withstand any load. As for what you said about being restricted on the next day, this is because the IP allocation is not implemented.

Reboot the switch and take a look. You can set up an IP on your computer first, and then change it back to automatically assigning an IP address after this IP is applied, so that it will generally be connected, and if it still doesn't work, restart the switch.

It doesn't matter if the insulating skin inside the single network cable is broken, because this whole one is made of live wire,..The network cable is divided into quality, and the better one is harder and can support up to 1000W electrical appliances. Of course, that's also.

1. Dangerous, if it is a box of two or three hundred yuan of network cables, many of them are copper-plated, and the outer rubber is also very poor, which can easily cause heating or short circuit.

2. Interference, the power cord and the network cable together will form electromagnetic interference, which will cause the network signal to lose packets, resulting in slow network speed or unconnection.

Landlord: Door:

Let's look at this from another angle:

If you think about the cost, that's it.

Can wires be used as network cables?

The result is: "It's not light!" "！(This object may be a person) and your network cable as a result of the wire:

It's also "not a light burn" (this object is a thing).

No, the ** line can be used as a network cable.

No, there is a layer of metal skin in the network cable, which can conduct electricity, and the heart is glass wire, so it cannot be used as a wire.

The network cable conducts electricity. However, it cannot be used as a wire.

Yes, but the power of the electrical appliances should not be too large, and it is still possible within 100 watts.

The wire is the wire, if your question is whether the weak current of the wire can be used for strong electricity, the answer is no.

OK. I've used it. The inside of the network cable is also a copper wire. However, when it comes to wires, you need to use two network cables.

Strip the plastic skin of the 8 thin cores in the network cable and screw them together, and you can probably top a 3 square millimeter copper wire.

Of course!

After connecting, it can be wrapped with waterproof tape and insulating tape. That's how I connected the network cable of our unit, but it must be aligned with the color, and the crystal heads at both ends must be in the same order.

No, because the network cable is a weak wire, so the internal copper wire is relatively thin. Charging is a strong electricity, the charging current is relatively large, and the wires required are relatively thick. The network cable cannot carry the high current when the battery is charging. It is easy to burn out or cause a disaster.

That's absolutely not allowed, the wire is composed of 2 or 3 parts, and the wire composed of 2 parts is: the live wire and the neutral line. Then the wire composed of 3 parts is the live wire, the neutral wire, and the ground wire.

So do you have these 2 or 3 inner wires in your network cable, even if there is, the copper core wire of the network cable is so thin that it can't carry the 220V AC current. Don't take any chances. This can be dangerous.

Or go buy AC wire.

The network cable is very thin, and it is definitely not possible to eat 220v, you can choose more than a dozen winding and parallel connections, and it is estimated that it can, I guess, I am not responsible for the network cable on fire.

Don't! The insulation level of the network cable is very low, and it is easy to break down. Or use wires!!

1. It depends on what kind of network cable it is.

a.Now some network cables are inferior goods, 4 aluminum, 4 iron, such network cables, don't think about being a power cable.

Identification method: cut out a little bit, and it can be attracted with a magnet, which is this kind of poor line.

2.If it is a network cable of copper wire.

You use 4 lamps, you can light a 40W lamp, more than enough, 2 as the neutral line, 2 as the live wire.

Of course, you can use 8 to get more power; 4 as the neutral line, the other 4 as the live line;

3.On 60w, don't use it, hehe, the insulating glue is too thin, easy to burn off, and it's okay to light a single lamp (30w 40w).

If you need to use telecommunications, please buy it at a regular store.

That's definitely not going to work.,How big is the current of 2000W?,How much current can a network cable withstand?,Although you merge the four into a group,But it can't actually withstand it.,Brother.。 For the sake of safety, don't save that little wire money, electricity is not a joke, take it seriously! Don't be sloppy.

Can you give up the money or buy the national standard.

Yes, I've seen someone take a network cable to connect an electric drill! The kind that drills holes in the wall!

Cow, hehe, nothing at all.

It can be used as a wire, but if your power is too great, don't use it, the network cable is very thin and will burn out.

Yes, but 2000 watts is too big and definitely not, and the copper wire in the network cable is estimated to be 200 watts.

Network cables are more expensive than wires, so don't waste them.

The company provides funeral activities and regular customer discounts.

When you only need 100m connections yes, the other two pairs are kept not used. When you want to connect to a 1000m network, all 8 wires need to be used. Therefore, the network cable is connected according to the standard 8 wires. In the future, it can be connected to 1000m at any time, and there is no need to move the line.

The rest is spare... It can also be used separately as another network...

Two pairs of internet speeds in China are sufficient, and the other two pairs are spare.

It is illegal to tie it to the household AC power, it is not safe, in case the AC wire heats, short circuit and other faults, the network cable will be scalded or burned, and the computer will be damaged in serious cases.

There is a slight effect, it is recommended to separate a certain distance....

It won't affect ah, how can it be affected.