What should I do if the hand of the Vacheron Constantin watch does not move

In fact, there are many reasons why mechanical watches do not go, such as: bumps, movement gear misalignment, magnetization of the watch, shelving for a long time, sludge drying, etc., generally divided into two kinds, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch.

Therefore, don't panic too much when you find that the mechanical watch is not leaving, and first distinguish which kind of big one it belongs to.

1. Insufficient power reserve. You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of speed and slowness, if it is still recommended to go to the store for testing.

2. The power is insufficient. If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy.

3. Having been beaten or impacted. The watch is very tight, if it is hit or dropped, it may cause loose damage to the internal parts, and it may also cause time problems, so it is recommended to go to the store for testing.

4. Maintenance is required. A lack of oil or wear and tear of the internal parts of the movement can cause time-keeping problems and require maintenance.

5. Under the influence of ambient temperature, the watch is magnetized: if the hairspring of the watch is magnetized, the watch will not be accurate. The influence of the wearer's usage habits may cause an increase in the error of the time, which will be sent to the store.

Note: 1. Mechanical watches vary according to the model and manufacturing quality of the movement, and the error of the general watch within 30 seconds per day is within the normal range. Some of the higher precision movements can reach around 10 seconds.

Hello, the reason why the pointer does not go could be:

1. Insufficient power: If the quartz watch suddenly finds that it is slow, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

2. Insufficient power reserve: You need to check whether the power is sufficient, if the amount of exercise is very small, the automatic watch may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of fast and slow.

3. The watch is magnetized: If the hairspring of the mechanical watch is magnetized, the watch will not be accurate.

4. Need for maintenance: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, and it needs to be sent to the designated maintenance point for maintenance services.

5. Hit or impacted: The watch is very precise, if it is hit or hit, it may cause loose damage to internal parts, and it may also cause time problems.

6. In addition to the above common situations, the influence of some ambient temperature and the wearer's usage habits may cause an increase in the timing error.

Recommendations for the use of mechanical watches:

1. Watches with manual winding movements should be wound at the same time every day as far as possible so that the watch has enough energy to operate in the next 24 hours.

2. The energy of the watch with automatic movement is ** in the movement of the wearer's arm, so there is no need to manually wind it under normal wearing, only when the wearer's exercise is not enough to replenish enough energy to the mainspring, it can be compensated by manual winding, and the crown rotation is controlled within 20 laps when winding.

3. For a self-winding watch that has not been worn for more than 40 hours, the crown should be turned 20 times to reactivate the movement when worn again.

4. In order to prevent moisture from penetrating into the case and maintain the waterproof performance of the watch, please make sure that the crown is locked at all times.

Hello, the problem of the watch not going can be considered from the following aspects:

1.The power of the table is insufficient.

An automatic watch only needs to be wound by moving your arm, but if you don't exercise much, or if you don't wear your watch for too long, the watch may not be able to run out of time or stop due to lack of power. Of course, you don't have to throw your arms as a hula hoop in order to wind your watch, just move normally.

2.Wearing time is too short.

If it's really caused by too little exercise, don't worry, just take off your watch and shake it horizontally for about 2 minutes before going to bed, and of course you can also shake it for 4 minutes, because then it can walk longer. If your watch can be wound, you can also wind it clockwise. In order for your watch to last longer, it is recommended to have him wear it on your wrist for at least 6 to 8 hours a day.

3.Hairspring failure.

If neither of the above two reasons is the case, it may be the cause of the hairspring. If you exercise too much, the clockwork will be tighter. If it is really a lack of power caused by the winding, usually between 9 and 12 o'clock in the evening, the "calendar function table" at this time his needle wheel began to drive the calendar wheel, the load is large, the watch is tired, at this time if the power is insufficient and no one pushes it, it is easy to stop.

During this time, don't reverse the dial, many mechanical watches have a plastic calendar wheel, and if you are not careful, you will break the gear, if you break the tooth, it will be stuck at this time every day, or it will no longer jump until a fixed date. That's why the mechanical watch stopped.

4.Bump failure.

The parts of the watch are very delicate and small, if you are careless and accidentally bump into it, or if you are healthy and bump into it. This can easily cause the movement parts to fall off or break directly.

All automatic watches must be worn or wound regularly in order to function properly. If the mechanism stops working for a long time, it will cause the watch to deteriorate for a long time. Generally speaking, the power reserve of a large three-hand watch is probably no more than 38 hours, which means that if you do not wear the watch for more than 45 hours, the watch will eventually stop due to the exhaustion of the mainspring.

Hello! I don't know what type of watch your watch is, whether it's a quartz watch or a mechanical watch, the quartz watch hand doesn't go away may be out of power. In the case of mechanical watches, it is necessary to detect to determine the reason why the watch hand does not go, and there is a multi-functional watch, the chronograph hand generally does not go, but the small seconds hand is walking!

If your watch encounters a fault, you can go to our store for free testing!

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

There will be after-sales ** on your warranty link, call after-sales ** to inquire about the after-sales address.

First of all, you look at your hand to indicate whether it is manually wound or automatic, and there are several reasons why the watch does not go in general

First: mechanical watches need to be cleaned and maintained within 2-3 years of wearing.

Second: If the watch type is fully automatic winding, there may be a reason for the lack of power that causes the watch not to go.

Third: it is a problem with the movement, it is recommended to go to a professional maintenance place to check it.

If the watch hand is lost or damaged, it can be replaced, so please don't worry too much. Since the hands are installed in layers, and the top tube is connected to the second hand, the second hand is usually lost. If the hands of the watch are dropped, the crown should be pulled out in time to stop moving, so as to prevent the hands from scratching the watch, dial or breaking themselves.

After pulling out the crown, please repair it in time to prevent the watch from dusting. In general, if there is no damage to the inside of the watch, it is relatively easy to repair, but if the wheel tube is deformed, broken or the parts are worn, the repair will be slightly more difficult.

Hello, glad to answer for you!

Reasons for inaccurate time: insufficient kinetic energy reserve of the watch, insufficient battery of the watch, the watch has been hit or hit by an external source, the watch has not been maintained for a long time, and the watch is affected by magnetic fields.

Solution: It is necessary to go to the after-sales center for testing and maintenance.

1.Please use and adjust the watch correctly, the automatic watch must be wound before the first use, but remember not to over-wind, so as not to damage the movement and jam the machinery, pay attention to adjust the head of the watch to gently push and push, not strong, after the adjustment to confirm the return, to avoid waterproof failure caused by the head is not tightened!

2.All mechanical watches have a run-in period, if there is a positive or negative difference of one minute within 24 hours during the run-in period, it is normal, and after the run-in period enters a stable stage and then makes a second adjustment!The run-in period is generally set at three months!

Adjustments can be made to the local watch line, or you can contact customer service to send ** whole!

3.The multi-function type should be careful not to press the head of the computer at will, and remember not to press too continuously!The multi-menu cannot be used when the winding is over-full, and the crystal sapphire glass cannot be rubbed against diamonds or glass!If you are unclear or have any questions in use, please contact customer service in time!

4.Date watch time adjustment method: a

First of all, pull out the watch handle to the time adjustment position, adjust the hand in the clockwise direction to stop after the jump, this is 24 o'clock at night, if you adjust before 12 noon, please adjust the hour and minute hand to the desired time;If the hour is adjusted after 12 noon, adjust the hour and minute hands to the desired time. b.I use a quick pull button to adjust a calendar, a week to the desired date, the week.

c.The weekly calendar change time is allowed to be completed within 4 hours after the calendar change. d.

Single-date watches are not allowed to use the quick-pull button to adjust the day from 11 p.m. to 1 a.m. every night. Dual-date watches are not allowed to use the quick-pull button to adjust the day from 11 p.m. to 5 a.m. every night.

Stop, there may be the following reasons:

1. See if the crown is pulled out, the crown is pulled out, and the watch stops.

2. Whether the second hand touches the glass, there will be a circle mark on the glass.

3. Whether the three watch hands are not well balanced, causing contact and causing stopping.

4. Whether the battery is exhausted or not, it generally needs to be replaced in 1-2 years.

1. The balance wheel touches the fork splint: the lower shaft tenon of the pendulum shaft is broken; The lower shock absorber is loose, and the shock spring falls off or is not pressed into the spring groove; The end face of the balance wheel jumps greatly caused by the deformation of the balance wheel; The fork splint is deformed or the fork splint screws are loose.

2. The escapement fork touches the main splint or the lower shock absorber: the lower fork drill is loose or the lower fork drill is thicker; The fork head is deformed or the fork head nail is deformed and touches the shock absorber; The shellac under the fork tile is too thick, touching the main splint.

3. Impact disc crossing plane: The impact disc collision plane is loose due to the interference between the double disc and the pendulum shaft is too small, resulting in the impact disc collision plane.

If there is a problem with the watch, it is recommended to go to the regular point of after-sales maintenance, not only the technician is more professional, the instrument is also more precise, and the **transparent is not messy**. My personal advice is to pass as soon as possible, otherwise the longer the time, the greater the problem with the watch, and the greater the economic loss. The main thing is that it is still more troublesome, and the repair time will become longer.

If it is an electronic watch, it may be that the watch is out of power, try to change the battery to see, if it has just been replaced or there is a problem, it is recommended to send it to the place where the watch is repaired to see if the watch is flooded.

If it is quartz, some large seconds are not gone, generally the three-eyed chronograph hand watch usually has a long second hand does not go, only the timing goes, a small plate in the three small plates has been walking is the second hand of the time, this is a power-saving design, most of the chronograph watches are like this, please see the manual for details.

If it is a mechanical watch, the time error is relatively large, and it is not as accurate as a quartz watch. It is recommended to swing the watch from side to side in a horizontal state for about 10 minutes before putting it down at night to replenish the winding and ensure normal time.

A fully automatic watch is self-winding by the swing of the arm, so it must be worn for at least 12 hours a day to ensure accurate timekeeping. The easiest way is to take it to repair, but it may be the following situations: the card is on the Xuan, the second hand is loose, shake a few times to see if it works, if it doesn't work, you can only send it over for repair.

The reason for the inaccurate timing of the watch is mostly due to the magnetization of the watch, lack of maintenance, watch balance spring failure, escapement system failure, parts slippage and other mechanical failures may cause the watch to appear fast and slow.

So what are the problems that can cause the watch to go inaccurately?

1. The watch is not powered enough.

2. Whether it is affected by magnetic field.

3. The surface oil dries up.

4. Damaged parts.

5. It is recommended to send it to a professional repair shop for processing.

Hehe, you are too rich, and you are too careless, it is equivalent to carrying a mid-level car in your hand and losing your tires. Vacheron Constantin lists special watches in the world, except for Patek Philippe and Audemars Piguet, and the entry-level is more than 100,000. You can lose the pointer, you are too careless, it is estimated that if this needle is lost, it will be lost for thousands of yuan.

It's no wonder that this watch can also lose the pointers. Unless it's an imitation.

It's a bit of a joke, if you really want to match, there is definitely no one in China, you have to buy it, and the merchant will send it to the original factory in Switzerland to match it for you.